[ Upstream commit 9f1168cf26 ]
The Intel IXP4xx PCI controller is only present on Intel IXP4xx
XScale-based network processor SoCs.
Add a dependency on ARCH_IXP4XX, to prevent asking the user about this
driver when configuring a kernel without support for the XScale
processor family.
Link: https://lore.kernel.org/r/6a88e55fe58fc280f4ff1ca83c154e4895b6dcbf.1624972789.git.geert+renesas@glider.be
Fixes: f7821b4934 ("PCI: ixp4xx: Add a new driver for IXP4xx")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1de58802f ]
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09c24094b2 ]
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 02bcec3ea5 upstream.
Measurements in different conditions showed that aardvark hardware PIO
response can take up to 1.44s. Increase wait timeout from 1ms to 1.5s to
ensure that we do not miss responses from hardware. After 1.44s hardware
returns errors (e.g. Completer abort).
The previous two patches fixed checking for PIO status, so now we can use
it to also catch errors which are reported by hardware after 1.44s.
After applying this patch, kernel can detect and print PIO errors to dmesg:
[ 6.879999] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100004
[ 6.896436] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
[ 6.913049] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100010
[ 6.929663] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100010
[ 6.953558] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100014
[ 6.970170] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100014
[ 6.994328] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
Without this patch kernel prints only a generic error to dmesg:
[ 5.246847] advk-pcie d0070000.pcie: config read/write timed out
Link: https://lore.kernel.org/r/20210722144041.12661-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da81 ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcb461e2bc upstream.
There is an issue that when PCIe switch is connected to an Armada 3700
board, there will be lots of warnings about PIO errors when reading the
config space. According to Aardvark PIO read and write sequence in HW
specification, the current way to check PIO status has the following
issues:
1) For PIO read operation, it reports the error message, which should be
avoided according to HW specification.
2) For PIO read and write operations, it only checks PIO operation complete
status, which is not enough, and error status should also be checked.
This patch aligns the code with Aardvark PIO read and write sequence in HW
specification on PIO status check and fix the warnings when reading config
space.
[pali: Fix CRS handling when CRSSVE is not enabled]
Link: https://lore.kernel.org/r/20210722144041.12661-2-pali@kernel.org
Tested-by: Victor Gu <xigu@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # b1bd571447 ("PCI: aardvark: Indicate error in 'val' when config read fails")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64f160e19e upstream.
In commit 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window configuration")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When both the old and the new PCI drivers are enabled
in the same kernel, there are a couple of namespace
conflicts that cause a build failure:
drivers/pci/controller/pci-ixp4xx.c:38: error: "IXP4XX_PCI_CSR" redefined [-Werror]
38 | #define IXP4XX_PCI_CSR 0x1c
|
In file included from arch/arm/mach-ixp4xx/include/mach/hardware.h:23,
from arch/arm/mach-ixp4xx/include/mach/io.h:15,
from arch/arm/include/asm/io.h:198,
from include/linux/io.h:13,
from drivers/pci/controller/pci-ixp4xx.c:20:
arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h:221: note: this is the location of the previous definition
221 | #define IXP4XX_PCI_CSR(x) ((volatile u32 *)(IXP4XX_PCI_CFG_BASE_VIRT+(x)))
|
drivers/pci/controller/pci-ixp4xx.c:148:12: error: 'ixp4xx_pci_read' redeclared as different kind of symbol
148 | static int ixp4xx_pci_read(struct ixp4xx_pci *p, u32 addr, u32 cmd, u32 *data)
| ^~~~~~~~~~~~~~~
Rename both the ixp4xx_pci_read/ixp4xx_pci_write functions and the
IXP4XX_PCI_CSR macro. In each case, I went with the version that
has fewer callers to keep the change small.
Fixes: f7821b4934 ("PCI: ixp4xx: Add a new driver for IXP4xx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: soc@kernel.org
Link: https://lore.kernel.org/r/20210721151546.2325937-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
- Fix multi-MSI base vector number allocation (Sandor Bodo-Merle)
- Restrict multi-MSI support to uniprocessor kernel (Sandor Bodo-Merle)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Support multi-MSI only on uniprocessor kernel
PCI: iproc: Fix multi-MSI base vector number allocation
- Decode PIO Posted/Non-posted Request correctly in error logging (Pali
Rohár)
- Work around incorrect Vendor ID in Marvell Armada 3700 (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Implement workaround for the readback value of VEND_ID
PCI: aardvark: Fix checking for PIO Non-posted Request
- Register IRQ handlers after device and data are ready (Javier Martinez
Canillas)
* pci/host/rockchip:
PCI: rockchip: Register IRQ handlers after device and data are ready
An IRQ handler may be called at any time after it is registered, so
anything it relies on must be ready before registration.
rockchip_pcie_subsys_irq_handler() and rockchip_pcie_client_irq_handler()
read registers in the PCIe controller, but we registered them before
turning on clocks to the controller. If either is called before the clocks
are turned on, the register reads fail and the machine hangs.
Similarly, rockchip_pcie_legacy_int_handler() uses rockchip->irq_domain,
but we installed it before initializing irq_domain.
Register IRQ handlers after their data structures are initialized and
clocks are enabled.
Found by enabling CONFIG_DEBUG_SHIRQ, which calls the IRQ handler when it
is being unregistered. An error during the probe path might cause this
unregistration and IRQ handler execution before the device or data
structure init has finished.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210608080409.1729276-1-javierm@redhat.com
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Pull hyperv updates from Wei Liu:
"Just a few minor enhancement patches and bug fixes"
* tag 'hyperv-next-signed-20210629' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
PCI: hv: Add check for hyperv_initialized in init_hv_pci_drv()
Drivers: hv: Move Hyper-V extended capability check to arch neutral code
drivers: hv: Fix missing error code in vmbus_connect()
x86/hyperv: fix logical processor creation
hv_utils: Fix passing zero to 'PTR_ERR' warning
scsi: storvsc: Use blk_mq_unique_tag() to generate requestIDs
Drivers: hv: vmbus: Copy packets sent by Hyper-V out of the ring buffer
hv_balloon: Remove redundant assignment to region_start
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Marvell Armada 3700 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in aardvark driver for both PCI vendor id and PCI
subsystem vendor id.
This change affects and fixes PCI vendor id of emulated PCIe root bridge.
After this change emulated PCIe root bridge has correct vendor id.
Link: https://lore.kernel.org/r/20210624222621.4776-5-pali@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
