commit 3c3c8e88c8 upstream.
There have been reports of approximately a 0.9%-1.7% failure rate in SMU
communication timeouts with s0i3 entry on some OEM designs. Currently
the design in amd-pmc is to try every 100us for up to 20ms.
However the GPU driver which also communicates with the SMU using a
mailbox register which the driver polls every 1us for up to 2000ms.
In the GPU driver this was increased by commit 055162645a ("drm/amd/pm:
increase time out value when sending msg to SMU")
Increase the maximum timeout used by amd-pmc to 2000ms to match this
behavior. This has been shown to improve the stability for machines
that randomly have failures.
Cc: stable@kernel.org
Reported-by: Julian Sikorski <belegdol@gmail.com>
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1629
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20210914020115.655-1-mario.limonciello@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d453ceb654 ]
Add trace event to report samples and their timestamp coming from the
EC. It allows to check if the timestamps are correct and the filter is
working correctly without introducing too much latency.
To enable these events:
cd /sys/kernel/debug/tracing/
echo 1 > events/cros_ec/enable
echo 0 > events/cros_ec/cros_ec_request_start/enable
echo 0 > events/cros_ec/cros_ec_request_done/enable
echo 1 > tracing_on
cat trace_pipe
Observe event flowing:
irq/105-chromeo-95 [000] .... 613.659758: cros_ec_sensorhub_timestamp: ...
irq/105-chromeo-95 [000] .... 613.665219: cros_ec_sensorhub_filter: dx: ...
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36d4a1d75 ]
When numa is used to map CPU to PCI device, the optimized path to read
from cached data is not working and still calls _isst_if_get_pci_dev().
The reason is that when caching the mapping, numa information is not
available as it is read later. So move the assignment of
isst_cpu_info[cpu].numa_node before calling _isst_if_get_pci_dev().
Fixes: aa2ddd2425 ("platform/x86: ISST: Use numa node id for cpu pci dev mapping")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210727165052.427238-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The gpiod_lookup_table.table passed to gpiod_add_lookup_table() must
be terminated with an empty entry, add this.
Note we have likely been getting away with this not being present because
the GPIO lookup code first matches on the dev_id, causing most lookups to
skip checking the table and the lookups which do check the table will
find a matching entry before reaching the end. With that said, terminating
these tables properly still is obviously the correct thing to do.
Fixes: f8eb0235f6 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210806115515.12184-1-hdegoede@redhat.com
360 degree hinges devices with dual KIOX010A + KIOX020A accelerometers
always have both a KIOX010A and a KIOX020A ACPI device (one for each
accel).
Theoretical some vendor may re-use some DSDT for a non-convertible
stripping out just the KIOX020A ACPI device from the DSDT. Check that
both ACPI devices are present to make the check more robust.
Fixes: 153cca9caa ("platform/x86: Add and use a dual_accel_detect() helper")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210802141000.978035-1-hdegoede@redhat.com
Various 360 degree hinges (yoga) style 2-in-1 devices use 2 accelerometers
to allow the OS to determine the angle between the display and the base of
the device.
On Windows these are read by a special HingeAngleService process which
calls undocumented ACPI methods, to let the firmware know if the 2-in-1 is
in tablet- or laptop-mode. The firmware may use this to disable the kbd and
touchpad to avoid spurious input in tablet-mode as well as to report
SW_TABLET_MODE info to the OS.
Since Linux does not call these undocumented methods, the SW_TABLET_MODE
info reported by various pdx86 drivers is incorrect on these devices.
Before this commit the intel-hid and thinkpad_acpi code already had 2
hardcoded checks for ACPI hardware-ids of dual-accel sensors to avoid
reporting broken info.
And now we also have a bug-report about the same problem in the intel-vbtn
code. Since there are at least 3 different ACPI hardware-ids in play, add
a new dual_accel_detect() helper which checks for all 3, rather then
adding different hardware-ids to the drivers as bug-reports trickle in.
Having shared code which checks all known hardware-ids is esp. important
for the intel-hid and intel-vbtn drivers as these are generic drivers
which are used on a lot of devices.
The BOSC0200 hardware-id requires special handling, because often it is
used for a single-accelerometer setup. Only in a few cases it refers to
a dual-accel setup, in which case there will be 2 I2cSerialBus resources
in the device's resource-list, so the helper checks for this.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209011
Reported-and-tested-by: Julius Lehmann <julius@devpi.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210729082134.6683-1-hdegoede@redhat.com
Fix 2 possible memleaks on error-exits from tlmi_analyze():
1. If the kzalloc of pwd_power fails, then not only free the atributes,
but also the allocated pwd_admin struct.
2. Freeing the attributes should also free the possible_values strings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210717143607.3580-3-hdegoede@redhat.com
tlmi_sysfs_init() calls tlmi_release_attr() on errors which calls
kobject_put() for attributes created by tlmi_analyze(), but if we
bail early because of an error, then this means that some of the
kobjects will not have been initialized yet; and we should thus not
call kobject_put() on them.
Switch from using kobject_init_and_add() inside tlmi_sysfs_init() to
initializing all the created kobjects directly in tlmi_analyze() and
only adding them from tlmi_sysfs_init(). This way all kobjects will
always be initialized when tlmi_release_attr() gets called.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210717143607.3580-2-hdegoede@redhat.com
Move the pending_reboot node under attributes dir where it should live, as
documented in: Documentation/ABI/testing/sysfs-class-firmware-attributes.
Also move the create / remove code to be together with the other code
populating / cleaning the attributes sysfs dir. In the removal path this
is necessary so that the remove is done before the
kset_unregister(tlmi_priv.attribute_kset) call.
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210717143607.3580-1-hdegoede@redhat.com
It was reported that on i386 config
------
on i386:
ld: drivers/platform/x86/amd-pmc.o: in function `s0ix_stats_show':
amd-pmc.c:(.text+0x100): undefined reference to `__udivdi3'
-------
The reason for this is that 64-bit integer division is not supported
on 32-bit architecture. Use do_div macro to fix this.
Fixes: b9a4fa6978 ("platform/x86: amd-pmc: Add support for logging s0ix counters")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org> # and build-tested
Link: https://lore.kernel.org/r/20210716153802.2929670-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Even the FCH SSC registers provides certain level of information
about the s0ix entry and exit times which comes handy when the SMU
fails to report the statistics via the mailbox communication.
This information is captured via a new debugfs file "s0ix_stats".
A non-zero entry in this counters would mean that the system entered
the s0ix state.
If s0ix entry time and exit time don't change during suspend to idle,
the silicon has not entered the deepest state.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210629084803.248498-6-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SMU provides a way to dump the s0ix debug statistics in the form of a
metrics table via a of set special mailbox commands.
Add support to the driver which can send these commands to SMU and expose
the information received via debugfs. The information contains the s0ix
entry/exit, active time of each IP block etc.
As a side note, SMU subsystem logging is not supported on Picasso based
SoC's.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210629084803.248498-5-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It was lately understood that the current mechanism available in the
driver to get SMU firmware info works only on internal SMU builds and
there is a separate way to get all the SMU logging counters (addressed
in the next patch). Hence remove all the smu info shown via debugfs as it
is no more useful.
Fixes: 156ec4731c ("platform/x86: amd-pmc: Add AMD platform support for S2Idle")
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210629084803.248498-3-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The protocol to submit a job request to SMU is to wait for
AMD_PMC_REGISTER_RESPONSE to return 1,meaning SMU is ready to take
requests. PMC driver has to make sure that the response code is always
AMD_PMC_RESULT_OK before making any command submissions.
When we submit a message to SMU, we have to wait until it processes
the request. Adding a read_poll_timeout() check as this was missing in
the existing code.
Also, add a mutex to protect amd_pmc_send_cmd() calls to SMU.
Fixes: 156ec4731c ("platform/x86: amd-pmc: Add AMD platform support for S2Idle")
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210629084803.248498-2-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
Pull HID updates from Jiri Kosina:
- patch series that ensures that hid-multitouch driver disables touch
and button-press reporting on hid-mt devices during suspend when the
device is not configured as a wakeup-source, from Hans de Goede
- support for ISH DMA on Intel EHL platform, from Even Xu
- support for Renoir and Cezanne SoCs, Ambient Light Sensor and Human
Presence Detection sensor for amd-sfh driver, from Basavaraj Natikar
- other assorted code cleanups and device-specific fixes/quirks
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (45 commits)
HID: thrustmaster: Switch to kmemdup() when allocate change_request
HID: multitouch: Disable event reporting on suspend when the device is not a wakeup-source
HID: logitech-dj: Implement may_wakeup ll-driver callback
HID: usbhid: Implement may_wakeup ll-driver callback
HID: core: Add hid_hw_may_wakeup() function
HID: input: Add support for Programmable Buttons
HID: wacom: Correct base usage for capacitive ExpressKey status bits
HID: amd_sfh: Add initial support for HPD sensor
HID: amd_sfh: Extend ALS support for newer AMD platform
HID: amd_sfh: Extend driver capabilities for multi-generation support
HID: surface-hid: Fix get-report request
HID: sony: fix freeze when inserting ghlive ps3/wii dongles
HID: usbkbd: Avoid GFP_ATOMIC when GFP_KERNEL is possible
HID: amd_sfh: change in maintainer
HID: intel-ish-hid: ipc: Specify that EHL no cache snooping
HID: intel-ish-hid: ishtp: Add dma_no_cache_snooping() callback
HID: intel-ish-hid: Set ISH driver depends on x86
HID: hid-input: add Surface Go battery quirk
HID: intel-ish-hid: Fix minor typos in comments
HID: usbmouse: Avoid GFP_ATOMIC when GFP_KERNEL is possible
...
This function returns negative error codes, zero (to indicate that
everything has been completed successfully) and one (to indicate that
more resources need to be handled still).
This code prints an uninitialized error message when the function
returns one which potentially leads to an Oops.
Fixes: 5de691bffe ("platform/x86: Add intel_skl_int3472 driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/YNXTkLNtiTDlFlZa@mwanda
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We must not free the possible_values string before we have called
sysfs_remove_group(kobj, &tlmi_attr_group) otherwise there is a race
where a sysfs read of possible_values could reference the free-ed
memory.
Move the kfree(setting->possible_values) together with the free of the
actual tlmi_attr_setting struct to avoid this race.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently attributes will show things like:
`BootOrderLock,Disable`
rather than just
`Disable`.
Of course this works, but the attribute is intended to be read by
userspace tools and not require further processing. That is a userspace
tool can display a drop down of `possible_values` and `current_value` is
one of them from the list.
This also aligns `think-lmi` with how `dell-wmi-sysman` works.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20210622200755.12379-3-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On an AMD based Lenovo T14, I find that the module doesn't work at
all, and instead has a traceback with messages like:
```
sysfs: cannot create duplicate filename '/devices/virtual/firmware-attributes/thinklmi/attributes/Reserved'
```
Duplicate and reserved values showing up appear to be a firmware bug,
but they shouldn't make the driver explode. So catch them and skip
them.
Fixes: a40cd7ef22 ("platform/x86: think-lmi: Add WMI interface support on Lenovo platforms")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20210622200755.12379-2-mario.limonciello@amd.com
[hdegoede@redhat.com: Add missing kfree(tlmi_priv.setting[i])]
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit 0ddcf3a6b4 ("platform/x86: think-lmi: Avoid potential read before
start of the buffer") moved the length == 0 up to before stripping the '\n'
which typically gets added when users echo a value to a sysfs-attribute
from the shell.
This avoids a potential buffer-underrun, but it also causes a behavioral
change, prior to this change "echo > kbdlang", iow writing just a single
'\n' would result in an EINVAL error, but after the change this gets
accepted setting kbdlang to an empty string.
Fix this by replacing the manual '\n' check with using strchrnul() to get
the length till '\n' or terminating 0 in one go; and then do the
length != 0 check after this.
Fixes: 0ddcf3a6b4 ("platform/x86: think-lmi: Avoid potential read before start of the buffer")
Reported-by: Juha Leppänen <juha_efku@dnainternet.net>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210621193648.44138-1-hdegoede@redhat.com
