Some busses, like I2C, strictly need to have the line handled
as open drain, i.e. not actively driven high. For this reason
the i2c-gpio.c bit-banged I2C driver is reimplementing open
drain handling outside of gpiolib.
This is not very optimal. Instead make it possible for a
consumer to explcitly express that the line must be handled
as open drain instead of allowing local hacks papering over
this issue.
The descriptor tables, whether DT, ACPI or board files, should
of course have flagged these lines as open drain. E.g.:
enum gpio_lookup_flags GPIO_OPEN_DRAIN for a board file, or
gpios = <&foo 42 GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN>; in a
device tree using <dt-bindings/gpio/gpio.h>
But more often than not, these descriptors are wrong. So
we need to make it possible for consumers to enforce this
open drain behaviour.
We now have two new enumerated GPIO descriptor config flags:
GPIOD_OUT_LOW_OPEN_DRAIN and GPIOD_OUT_HIGH_OPEN_DRAIN
that will set up the lined enforced as open drain as output
low or high, using open drain (if the driver supports it)
or using open drain emulation (setting the line as input
to drive it high) from the gpiolib core.
Cc: linux-gpio@vger.kernel.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the GPIO-based I2C-driver to using GPIO
descriptors instead of the old global numberspace-based
GPIO interface. We:
- Convert the driver to unconditionally grab two GPIOs
from the device by index 0 (SDA) and 1 (SCL) which
will work fine with device tree and descriptor tables.
The existing device trees will continue to work just
like before, but without any roundtrip through the
global numberspace.
- Brutally convert all boardfiles still passing global
GPIOs by registering descriptor tables associated with
the devices instead so this driver does not need to keep
supporting passing any GPIO numbers as platform data.
There is no stepwise approach as elegant as this, I
strongly prefer this big hammer over any antsteps for this
conversion. This way the old GPIO numbers go away and
NEVER COME BACK.
Special conversion for the different boards utilizing
I2C-GPIO:
- EP93xx (arch/arm/mach-ep93xx): pretty straight forward as
all boards were using the same two GPIO lines, just define
these two in a lookup table for "i2c-gpio" and register
these along with the device. None of them define any
other platform data so just pass NULL as platform data.
This platform selects GPIOLIB so all should be smooth.
The pins appear on a gpiochip for bank "G" as pins 1 (SDA)
and 0 (SCL).
- IXP4 (arch/arm/mach-ixp4): descriptor tables have to
be registered for each board separately. They all use
"IXP4XX_GPIO_CHIP" so it is pretty straight forward.
Most board define no other platform data than SCL/SDA
so they can drop the #include of <linux/i2c-gpio.h> and
assign NULL to platform data.
The "goramo_mlr" (Goramo Multilink Router) board is a bit
worrisome: it implements its own I2C bit-banging in the
board file, and optionally registers an I2C serial port,
but claims the same GPIO lines for itself in the board file.
This is not going to work: there will be competition for the
GPIO lines, so delete the optional extra I2C bus instead, no
I2C devices are registered on it anyway, there are just hints
that it may contain an EEPROM that may be accessed from
userspace. This needs to be fixed up properly by the serial
clock using I2C emulation so drop a note in the code.
- KS8695 board acs5k (arch/arm/mach-ks8695/board-acs5.c)
has some platform data in addition to the pins so it needs to
be kept around sans GPIO lines. Its GPIO chip is named
"KS8695" and the arch selects GPIOLIB.
- PXA boards (arch/arm/mach-pxa/*) use some of the platform
data so it needs to be preserved here. The viper board even
registers two GPIO I2Cs. The gpiochip is named "gpio-pxa" and
the arch selects GPIOLIB.
- SA1100 Simpad (arch/arm/mach-sa1100/simpad.c) defines a GPIO
I2C bus, and the arch selects GPIOLIB.
- Blackfin boards (arch/blackfin/bf533 etc) for these I assume
their I2C GPIOs refer to the local gpiochip defined in
arch/blackfin/kernel/bfin_gpio.c names "BFIN-GPIO".
The arch selects GPIOLIB. The boards get spiked with
IF_ENABLED(I2C_GPIO) but that is a side effect of it
being like that already (I would just have Kconfig select
I2C_GPIO and get rid of them all.) I also delete any
platform data set to 0 as it will get that value anyway
from static declartions of platform data.
- The MIPS selects GPIOLIB and the Alchemy machine is using
two local GPIO chips, one of them has a GPIO I2C. We need
to adjust the local offset from the global number space here.
The ATH79 has a proper GPIO driver in drivers/gpio/gpio-ath79.c
and AFAICT the chip is named "ath79-gpio" and the PB44
PCF857x expander spawns from this on GPIO 1 and 0. The latter
board only use the platform data to specify pins so it can be
cut altogether after this.
- The MFD Silicon Motion SM501 is a special case. It dynamically
spawns an I2C bus off the MFD using sm501_create_subdev().
We use an approach to dynamically create a machine descriptor
table and attach this to the "SM501-LOW" or "SM501-HIGH"
gpiochip. We use chip-local offsets to grab the right lines.
We can get rid of two local static inline helpers as part
of this refactoring.
Cc: Steven Miao <realmz6@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Wu, Aaron <Aaron.Wu@analog.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For devices not instantiated through ACPI the i2c-client's device-name
gets set to <busnr>-<addr> by default, e.g. "0-0022" this means that
the device-name is dependent on the order in which the i2c-busses are
enumerated.
In some cases having a predictable constant device-name is desirable,
for example on non device-tree platforms the link between a regulator
and its consumers is specified by the platform code by setting
regulator_init_data.consumers. This array identifies the regulator's
consumers by dev_name and supply(-name). Which requires a constant
dev_name.
This commit adds a dev_name field to i2c_board_info allowing
platform code to set a contstant dev_name so that the device can
be identified by its dev_name in other platform code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org> (live at ELCE17)
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (live at ELCE17)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull irq fixes from Thomas Gleixner:
"A set of small fixes mostly in the irq drivers area:
- Make the tango irq chip work correctly, which requires a new
function in the generiq irq chip implementation
- A set of updates to the GIC-V3 ITS driver removing a bogus BUG_ON()
and parsing the VCPU table size correctly"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: generic chip: remove irq_gc_mask_disable_reg_and_ack()
irqchip/tango: Use irq_gc_mask_disable_and_ack_set
genirq: generic chip: Add irq_gc_mask_disable_and_ack_set()
irqchip/gic-v3-its: Add missing changes to support 52bit physical address
irqchip/gic-v3-its: Fix the incorrect parsing of VCPU table size
irqchip/gic-v3-its: Fix the incorrect BUG_ON in its_init_vpe_domain()
DT: arm,gic-v3: Update the ITS size in the examples
Pull networking fixes from David Miller:
"A little more than usual this time around. Been travelling, so that is
part of it.
Anyways, here are the highlights:
1) Deal with memcontrol races wrt. listener dismantle, from Eric
Dumazet.
2) Handle page allocation failures properly in nfp driver, from Jaku
Kicinski.
3) Fix memory leaks in macsec, from Sabrina Dubroca.
4) Fix crashes in pppol2tp_session_ioctl(), from Guillaume Nault.
5) Several fixes in bnxt_en driver, including preventing potential
NVRAM parameter corruption from Michael Chan.
6) Fix for KRACK attacks in wireless, from Johannes Berg.
7) rtnetlink event generation fixes from Xin Long.
8) Deadlock in mlxsw driver, from Ido Schimmel.
9) Disallow arithmetic operations on context pointers in bpf, from
Jakub Kicinski.
10) Missing sock_owned_by_user() check in sctp_icmp_redirect(), from
Xin Long.
11) Only TCP is supported for sockmap, make that explicit with a
check, from John Fastabend.
12) Fix IP options state races in DCCP and TCP, from Eric Dumazet.
13) Fix panic in packet_getsockopt(), also from Eric Dumazet.
14) Add missing locked in hv_sock layer, from Dexuan Cui.
15) Various aquantia bug fixes, including several statistics handling
cures. From Igor Russkikh et al.
16) Fix arithmetic overflow in devmap code, from John Fastabend.
17) Fix busted socket memory accounting when we get a fault in the tcp
zero copy paths. From Willem de Bruijn.
18) Don't leave opt->tot_len uninitialized in ipv6, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
stmmac: Don't access tx_q->dirty_tx before netif_tx_lock
ipv6: flowlabel: do not leave opt->tot_len with garbage
of_mdio: Fix broken PHY IRQ in case of probe deferral
textsearch: fix typos in library helpers
rxrpc: Don't release call mutex on error pointer
net: stmmac: Prevent infinite loop in get_rx_timestamp_status()
net: stmmac: Fix stmmac_get_rx_hwtstamp()
net: stmmac: Add missing call to dev_kfree_skb()
mlxsw: spectrum_router: Configure TIGCR on init
mlxsw: reg: Add Tunneling IPinIP General Configuration Register
net: ethtool: remove error check for legacy setting transceiver type
soreuseport: fix initialization race
net: bridge: fix returning of vlan range op errors
sock: correct sk_wmem_queued accounting on efault in tcp zerocopy
bpf: add test cases to bpf selftests to cover all access tests
bpf: fix pattern matches for direct packet access
bpf: fix off by one for range markings with L{T, E} patterns
bpf: devmap fix arithmetic overflow in bitmap_size calculation
net: aquantia: Bad udp rate on default interrupt coalescing
net: aquantia: Enable coalescing management via ethtool interface
...
Pull input fixes from Dmitry Torokhov:
- joydev now implements a blacklist to avoid creating joystick nodes
for accelerometers found in composite devices such as PlaStation
controllers
- assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-psu - check if CDC union descriptor is sane
Input: joydev - blacklist ds3/ds4/udraw motion sensors
Input: allow matching device IDs on property bits
Input: factor out and export input_device_id matching code
Input: goodix - poll the 'buffer status' bit before reading data
Input: axp20x-pek - fix module not auto-loading for axp221 pek
Input: tca8418 - enable interrupt after it has been requested
Input: stmfts - fix setting ABS_MT_POSITION_* maximum size
Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
Input: synaptics - disable kernel tracking on SMBus devices
Pull ARM SoC fixes from Arnd Bergmann:
"Here is another set of bugfixes for ARM SoCs, mostly harmless:
- a boot regression fix on ux500
- PCIe interrupts on NXP i.MX7 and on Marvell Armada 7K/8K were wired
up wrong, in different ways
- Armada XP support for large memory never worked
- the socfpga reset controller now builds on 64-bit
- minor device tree corrections on gemini, mvebu, r-pi 3, rockchip
and at91"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: Fix regression while init PM domains
ARM: dts: fix PCLK name on Gemini and MOXA ART
arm64: dts: rockchip: fix typo in iommu nodes
arm64: dts: rockchip: correct vqmmc voltage for rk3399 platforms
ARM: dts: imx7d: Invert legacy PCI irq mapping
bus: mbus: fix window size calculation for 4GB windows
ARM: dts: at91: sama5d2: add ADC hw trigger edge type
ARM: dts: at91: sama5d2_xplained: enable ADTRG pin
ARM: dts: at91: at91-sama5d27_som1: fix PHY ID
ARM: dts: bcm283x: Fix console path on RPi3
reset: socfpga: fix for 64-bit compilation
ARM: dts: Fix I2C repeated start issue on Armada-38x
arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
arm64: dts: salvator-common: add 12V regulator to backlight
ARM: dts: sun6i: Fix endpoint IDs in second display pipeline
arm64: allwinner: a64: pine64: Use dcdc1 regulator for mmc0
SK_SKB BPF programs are run from the socket/tcp context but early in
the stack before much of the TCP metadata is needed in tcp_skb_cb. So
we can use some unused fields to place BPF metadata needed for SK_SKB
programs when implementing the redirect function.
This allows us to drop the preempt disable logic. It does however
require an API change so sk_redirect_map() has been updated to
additionally provide ctx_ptr to skb. Note, we do however continue to
disable/enable preemption around actual BPF program running to account
for map updates.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull key handling fixes from James Morris:
"This includes a fix for the capabilities code from Colin King, and a
set of further fixes for the keys subsystem. From David:
- Fix a bunch of places where kernel drivers may access revoked
user-type keys and don't do it correctly.
- Fix some ecryptfs bits.
- Fix big_key to require CONFIG_CRYPTO.
- Fix a couple of bugs in the asymmetric key type.
- Fix a race between updating and finding negative keys.
- Prevent add_key() from updating uninstantiated keys.
- Make loading of key flags and expiry time atomic when not holding
locks"
* 'fixes-v4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
commoncap: move assignment of fs_ns to avoid null pointer dereference
pkcs7: Prevent NULL pointer dereference, since sinfo is not always set.
KEYS: load key flags and expiry time atomically in proc_keys_show()
KEYS: Load key expiry time atomically in keyring_search_iterator()
KEYS: load key flags and expiry time atomically in key_validate()
KEYS: don't let add_key() update an uninstantiated key
KEYS: Fix race between updating and finding a negative key
KEYS: checking the input id parameters before finding asymmetric key
KEYS: Fix the wrong index when checking the existence of second id
security/keys: BIG_KEY requires CONFIG_CRYPTO
ecryptfs: fix dereference of NULL user_key_payload
fscrypt: fix dereference of NULL user_key_payload
lib/digsig: fix dereference of NULL user_key_payload
FS-Cache: fix dereference of NULL user_key_payload
KEYS: encrypted: fix dereference of NULL user_key_payload
Because many of RCU's files have not been included into docbook, a
number of errors have accumulated. This commit fixes them.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduces a "register private expedited" membarrier command which
allows eventual removal of important memory barrier constraints on the
scheduler fast-paths. It changes how the "private expedited" membarrier
command (new to 4.14) is used from user-space.
This new command allows processes to register their intent to use the
private expedited command. This affects how the expedited private
command introduced in 4.14-rc is meant to be used, and should be merged
before 4.14 final.
Processes are now required to register before using
MEMBARRIER_CMD_PRIVATE_EXPEDITED, otherwise that command returns EPERM.
This fixes a problem that arose when designing requested extensions to
sys_membarrier() to allow JITs to efficiently flush old code from
instruction caches. Several potential algorithms are much less painful
if the user register intent to use this functionality early on, for
example, before the process spawns the second thread. Registering at
this time removes the need to interrupt each and every thread in that
process at the first expedited sys_membarrier() system call.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let's allow matching input devices on their property bits, both in-kernel
and when generating module aliases.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out and export input_match_device_id() so that modules may use it.
It will be needed by joydev to blacklist accelerometers in composite
devices.
Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull sound fixes from Takashi Iwai:
"We've got slightly more fixes than wished, but heading to a good
shape. Most of changes are about HD-audio fixes, one for a buggy code
that went into 4.13, and another for avoiding a crash due to buggy
BIOS.
Apart from HD-audio, a sequencer core change that is only for UP
config (which must be pretty rare nowadays), and a USB-audio quirk as
usual"
* tag 'sound-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix incorrect TLV callback check introduced during set_fs() removal
ALSA: hda: Remove superfluous '-' added by printk conversion
ALSA: hda: Abort capability probe at invalid register read
ALSA: seq: Enable 'use' locking in all configurations
ALSA: usb-audio: Add native DSD support for Pro-Ject Pre Box S2 Digital
Pull "mvebu fixes for 4.14 (part 2)" from Gregory CLEMENT
Two device tree related fixes:
- One on Armada 38x using a other compatible string for I2C in order
to cover an errata.
- One for Armada 7K/8K fixing a typo on interrupt-map property for
PCIe leading to fail PME and AER root port service initialization
And the last one for the mbus fixing the window size calculation when
it exceed 32bits
* tag 'mvebu-fixes-4.14-2' of git://git.infradead.org/linux-mvebu:
bus: mbus: fix window size calculation for 4GB windows
ARM: dts: Fix I2C repeated start issue on Armada-38x
arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
The commit 99b5c5bb9a ("ALSA: hda - Remove the use of set_fs()")
converted the get_kctl_0dB_offset() call for killing set_fs() usage in
HD-audio codec code. The conversion assumed that the TLV callback
used in HD-audio code is only snd_hda_mixer_amp() and applies the TLV
calculation locally.
Although this assumption is correct, and all slave kctls are actually
with that callback, the current code is still utterly buggy; it
doesn't hit this condition and falls back to the next check. It's
because the function gets called after adding slave kctls to vmaster.
By assigning a slave kctl, the slave kctl object is faked inside
vmaster code, and the whole kctl ops are overridden. Thus the
callback op points to a different value from what we've assumed.
More badly, as reported by the KERNEXEC and UDEREF features of PaX,
the code flow turns into the unexpected pitfall. The next fallback
check is SNDRV_CTL_ELEM_ACCESS_TLV_READ access bit, and this always
hits for each kctl with TLV. Then it evaluates the callback function
pointer wrongly as if it were a TLV array. Although currently its
side-effect is fairly limited, this incorrect reference may lead to an
unpleasant result.
For addressing the regression, this patch introduces a new helper to
vmaster code, snd_ctl_apply_vmaster_slaves(). This works similarly
like the existing map_slaves() in hda_codec.c: it loops over the slave
list of the given master, and applies the given function to each
slave. Then the initializer function receives the right kctl object
and we can compare the correct pointer instead of the faked one.
Also, for catching the similar breakage in future, give an error
message when the unexpected TLV callback is found and bail out
immediately.
Fixes: 99b5c5bb9a ("ALSA: hda - Remove the use of set_fs()")
Reported-by: PaX Team <pageexec@freemail.hu>
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Consolidate KEY_FLAG_INSTANTIATED, KEY_FLAG_NEGATIVE and the rejection
error into one field such that:
(1) The instantiation state can be modified/read atomically.
(2) The error can be accessed atomically with the state.
(3) The error isn't stored unioned with the payload pointers.
This deals with the problem that the state is spread over three different
objects (two bits and a separate variable) and reading or updating them
atomically isn't practical, given that not only can uninstantiated keys
change into instantiated or rejected keys, but rejected keys can also turn
into instantiated keys - and someone accessing the key might not be using
any locking.
The main side effect of this problem is that what was held in the payload
may change, depending on the state. For instance, you might observe the
key to be in the rejected state. You then read the cached error, but if
the key semaphore wasn't locked, the key might've become instantiated
between the two reads - and you might now have something in hand that isn't
actually an error code.
The state is now KEY_IS_UNINSTANTIATED, KEY_IS_POSITIVE or a negative error
code if the key is negatively instantiated. The key_is_instantiated()
function is replaced with key_is_positive() to avoid confusion as negative
keys are also 'instantiated'.
Additionally, barriering is included:
(1) Order payload-set before state-set during instantiation.
(2) Order state-read before payload-read when using the key.
Further separate barriering is necessary if RCU is being used to access the
payload content after reading the payload pointers.
Fixes: 146aa8b145 ("KEYS: Merge the type-specific data with the payload data")
Cc: stable@vger.kernel.org # v4.4+
Reported-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
register_netdevice() could fail early when we have an invalid
dev name, in which case ->ndo_uninit() is not called. For tun
device, this is a problem because a timer etc. are already
initialized and it expects ->ndo_uninit() to clean them up.
We could move these initializations into a ->ndo_init() so
that register_netdevice() knows better, however this is still
complicated due to the logic in tun_detach().
Therefore, I choose to just call dev_get_valid_name() before
register_netdevice(), which is quicker and much easier to audit.
And for this specific case, it is already enough.
Fixes: 96442e4242 ("tuntap: choose the txq based on rxq")
Reported-by: Dmitry Alexeev <avekceeb@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull irqchip updates for 4.14-rc5 from Marc Zyngier:
- Fix unfortunate mistake in the GICv3 ITS binding example
- Two fixes for the recently merged GICv4 support
- GICv3 ITS 52bit PA fixes
- Generic irqchip mask-ack fix, and its application to the tango irqchip
Pull char/misc driver fixes from Greg KH:
"Here are 4 patches to resolve some char/misc driver issues found these
past weeks.
One of them is a mei bugfix and another is a new mei device id. There
is also a hyper-v fix for a reported issue, and a binder issue fix for
a problem reported by a few people.
All of these have been in my tree for a while, I don't know if
linux-next is really testing much this month. But 0-day is happy with
them :)"
* tag 'char-misc-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix use-after-free in binder_transaction()
Drivers: hv: vmbus: Fix bugs in rescind handling
mei: me: add gemini lake devices id
mei: always use domain runtime pm callbacks.
The pci-rcar driver is enabled for compile tests, and this has shown that
the driver cannot build without CONFIG_OF, following the inclusion of
commit f8f2fe7355 ("PCI: rcar: Use new OF interrupt mapping when possible"):
drivers/pci/host/pcie-rcar.c: In function 'pci_dma_range_parser_init':
drivers/pci/host/pcie-rcar.c:1039:2: error: implicit declaration of function 'of_n_addr_cells' [-Werror=implicit-function-declaration]
parser->pna = of_n_addr_cells(node);
^
As pointed out by Ben Dooks and Geert Uytterhoeven, this is actually
supposed to build fine, which we can achieve if we make the declaration
of of_irq_parse_and_map_pci conditional on CONFIG_OF and provide an
empty inline function otherwise, as we do for a lot of other of
interfaces.
This lets us build the rcar_pci driver again without CONFIG_OF for build
testing. All platforms using this driver select OF, so this doesn't
change anything for the users.
[akpm@linux-foundation.org: be consistent with surrounding code]
Link: http://lkml.kernel.org/r/20170911200805.3363318-1-arnd@arndb.de
Fixes: c25da47788 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Any usage of the irq_gc_mask_disable_reg_and_ack() function has
been replaced with the desired functionality.
The incorrect and ambiguously named function is removed here to
prevent accidental misuse.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_gc_mask_disable_reg_and_ack() function name implies that it
provides the combined functions of irq_gc_mask_disable_reg() and
irq_gc_ack(). However, the implementation does not actually do
that since it writes the mask instead of the disable register. It
also does not maintain the mask cache which makes it inappropriate
to use with other masking functions.
In addition, commit 659fb32d1b ("genirq: replace irq_gc_ack() with
{set,clr}_bit variants (fwd)") effectively renamed irq_gc_ack() to
irq_gc_ack_set_bit() so this function probably should have also been
renamed at that time.
The generic chip code currently provides three functions for use
with the irq_mask member of the irq_chip structure and two functions
for use with the irq_ack member of the irq_chip structure. These
functions could be combined into six functions for use with the
irq_mask_ack member of the irq_chip structure. However, since only
one of the combinations is currently used, only the function
irq_gc_mask_disable_and_ack_set() is added by this commit.
The '_reg' and '_bit' portions of the base function name were left
out of the new combined function name in an attempt to keep the
function name length manageable with the 80 character source code
line length while still allowing the distinct aspects of each
combination to be captured by the name.
If other combinations are desired in the future please add them to
the irq generic chip library at that time.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The current ITS driver works fine as long as normal memory and GICR
regions are located within the lower 48bit (>=0 && <2^48) physical
address space. Some of the registers GICR_PEND/PROP, GICR_VPEND/VPROP
and GITS_CBASER are handled properly but not all when configuring
the hardware with 52bit physical address.
This patch does the following changes to support 52bit PA.
-Handle 52bit PA in GITS_BASERn.
-Fix ITT_addr width to 52bits, bits[51:8].
-Fix RDbase width to 52bits, bits[51:16].
-Fix VPT_addr width to 52bits, bits[51:16].
Definition of the GITS_BASERn register when ITS PageSize is 64KB:
-Bits[47:16] of the register provide bits[47:16] of the table PA.
-Bits[15:12] of the register provide bits[51:48] of the table PA.
-Bits[15:00] of the base physical address are 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull sound fixes from Takashi Iwai:
"It's been a busy week for defending the attacks from fuzzer people.
This contains various USB-audio driver fixes and sequencer core fixes
spotted by syzkaller and other fuzzer, as well as one quirk for a
Plantronics USB audio device"
* tag 'sound-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: caiaq: Fix stray URB at probe error path
ALSA: seq: Fix use-after-free at creating a port
ALSA: usb-audio: Kill stray URB at exiting
ALSA: line6: Fix leftover URB at error-path during probe
ALSA: line6: Fix NULL dereference at podhd_disconnect()
ALSA: line6: Fix missing initialization before error path
ALSA: seq: Fix copy_from_user() call inside lock
ALSA: usb-audio: Add sample rate quirk for Plantronics P610
At least the Armada XP SoC supports 4GB on a single DRAM window. Because
the size register values contain the actual size - 1, the MSB is set in
that case. For example, the SDRAM window's control register's value is
0xffffffe1 for 4GB (bits 31 to 24 contain the size).
The MBUS driver reads back each window's size from registers and
calculates the actual size as (control_reg | ~DDR_SIZE_MASK) + 1, which
overflows for 32 bit values, resulting in other miscalculations further
on (a bad RAM window for the CESA crypto engine calculated by
mvebu_mbus_setup_cpu_target_nooverlap() in my case).
This patch changes the type in 'struct mbus_dram_window' from u32 to
u64, which allows us to keep using the same register calculation code in
most MBUS-using drivers (which calculate ->size - 1 again).
Fixes: fddddb52a6 ("bus: introduce an Marvell EBU MBus driver")
CC: stable@vger.kernel.org
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Eric reported a sysbench regression against commit:
3fed382b46 ("sched/numa: Implement NUMA node level wake_affine()")
Similarly, Rik was looking at the NAS-lu.C benchmark, which regressed
against his v3.10 enterprise kernel.
PRE (current tip/master):
ivb-ep sysbench:
2: [30 secs] transactions: 64110 (2136.94 per sec.)
5: [30 secs] transactions: 143644 (4787.99 per sec.)
10: [30 secs] transactions: 274298 (9142.93 per sec.)
20: [30 secs] transactions: 418683 (13955.45 per sec.)
40: [30 secs] transactions: 320731 (10690.15 per sec.)
80: [30 secs] transactions: 355096 (11834.28 per sec.)
hsw-ex NAS:
OMP_PROC_BIND/lu.C.x_threads_144_run_1.log: Time in seconds = 18.01
OMP_PROC_BIND/lu.C.x_threads_144_run_2.log: Time in seconds = 17.89
OMP_PROC_BIND/lu.C.x_threads_144_run_3.log: Time in seconds = 17.93
lu.C.x_threads_144_run_1.log: Time in seconds = 434.68
lu.C.x_threads_144_run_2.log: Time in seconds = 405.36
lu.C.x_threads_144_run_3.log: Time in seconds = 433.83
POST (+patch):
ivb-ep sysbench:
2: [30 secs] transactions: 64494 (2149.75 per sec.)
5: [30 secs] transactions: 145114 (4836.99 per sec.)
10: [30 secs] transactions: 278311 (9276.69 per sec.)
20: [30 secs] transactions: 437169 (14571.60 per sec.)
40: [30 secs] transactions: 669837 (22326.73 per sec.)
80: [30 secs] transactions: 631739 (21055.88 per sec.)
hsw-ex NAS:
lu.C.x_threads_144_run_1.log: Time in seconds = 23.36
lu.C.x_threads_144_run_2.log: Time in seconds = 22.96
lu.C.x_threads_144_run_3.log: Time in seconds = 22.52
This patch takes out all the shiny wake_affine() stuff and goes back to
utter basics. Between the two CPUs involved with the wakeup (the CPU
doing the wakeup and the CPU we ran on previously) pick the CPU we can
run on _now_.
This restores much of the regressions against the older kernels,
but leaves some ground in the overloaded case. The default-enabled
WA_WEIGHT (which will be introduced in the next patch) is an attempt
to address the overloaded situation.
Reported-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jinpuwang@gmail.com
Cc: vcaputo@pengaru.com
Fixes: 3fed382b46 ("sched/numa: Implement NUMA node level wake_affine()")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull networking fixes from David Miller:
1) Fix object leak on IPSEC offload failure, from Steffen Klassert.
2) Fix range checks in ipset address range addition operations, from
Jozsef Kadlecsik.
3) Fix pernet ops unregistration order in ipset, from Florian Westphal.
4) Add missing netlink attribute policy for nl80211 packet pattern
attrs, from Peng Xu.
5) Fix PPP device destruction race, from Guillaume Nault.
6) Write marks get lost when BPF verifier processes R1=R2 register
assignments, causing incorrect liveness information and less state
pruning. Fix from Alexei Starovoitov.
7) Fix blockhole routes so that they are marked dead and therefore not
cached in sockets, otherwise IPSEC stops working. From Steffen
Klassert.
8) Fix broadcast handling of UDP socket early demux, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan
net: thunderx: mark expected switch fall-throughs in nicvf_main()
udp: fix bcast packet reception
netlink: do not set cb_running if dump's start() errs
ipv4: Fix traffic triggered IPsec connections.
ipv6: Fix traffic triggered IPsec connections.
ixgbe: incorrect XDP ring accounting in ethtool tx_frame param
net: ixgbe: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
Revert commit 1a8b6d76dc ("net:add one common config...")
ixgbe: fix masking of bits read from IXGBE_VXLANCTRL register
ixgbe: Return error when getting PHY address if PHY access is not supported
netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'
netfilter: SYNPROXY: skip non-tcp packet in {ipv4, ipv6}_synproxy_hook
tipc: Unclone message at secondary destination lookup
tipc: correct initialization of skb list
gso: fix payload length when gso_size is zero
mlxsw: spectrum_router: Avoid expensive lookup during route removal
bpf: fix liveness marking
doc: Fix typo "8023.ad" in bonding documentation
ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real
...
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix packet drops due to incorrect ECN handling in IPVS, from Vadim
Fedorenko.
2) Fix splat with mark restoration in xt_socket with non-full-sock,
patch from Subash Abhinov Kasiviswanathan.
3) ipset bogusly bails out when adding IPv4 range containing more than
2^31 addresses, from Jozsef Kadlecsik.
4) Incorrect pernet unregistration order in ipset, from Florian Westphal.
5) Races between dump and swap in ipset results in BUG_ON splats, from
Ross Lagerwall.
6) Fix chain renames in nf_tables, from JingPiao Chen.
7) Fix race in pernet codepath with ebtables table registration, from
Artem Savkov.
8) Memory leak in error path in set name allocation in nf_tables, patch
from Arvind Yadav.
9) Don't dump chain counters if they are not available, this fixes a
crash when listing the ruleset.
10) Fix out of bound memory read in strlcpy() in x_tables compat code,
from Eric Dumazet.
11) Make sure we only process TCP packets in SYNPROXY hooks, patch from
Lin Zhang.
12) Cannot load rules incrementally anymore after xt_bpf with pinned
objects, added in revision 1. From Shmulik Ladkani.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2c16d60332 ("netfilter: xt_bpf: support ebpf") introduced
support for attaching an eBPF object by an fd, with the
'bpf_mt_check_v1' ABI expecting the '.fd' to be specified upon each
IPT_SO_SET_REPLACE call.
However this breaks subsequent iptables calls:
# iptables -A INPUT -m bpf --object-pinned /sys/fs/bpf/xxx -j ACCEPT
# iptables -A INPUT -s 5.6.7.8 -j ACCEPT
iptables: Invalid argument. Run `dmesg' for more information.
That's because iptables works by loading existing rules using
IPT_SO_GET_ENTRIES to userspace, then issuing IPT_SO_SET_REPLACE with
the replacement set.
However, the loaded 'xt_bpf_info_v1' has an arbitrary '.fd' number
(from the initial "iptables -m bpf" invocation) - so when 2nd invocation
occurs, userspace passes a bogus fd number, which leads to
'bpf_mt_check_v1' to fail.
One suggested solution [1] was to hack iptables userspace, to perform a
"entries fixup" immediatley after IPT_SO_GET_ENTRIES, by opening a new,
process-local fd per every 'xt_bpf_info_v1' entry seen.
However, in [2] both Pablo Neira Ayuso and Willem de Bruijn suggested to
depricate the xt_bpf_info_v1 ABI dealing with pinned ebpf objects.
This fix changes the XT_BPF_MODE_FD_PINNED behavior to ignore the given
'.fd' and instead perform an in-kernel lookup for the bpf object given
the provided '.path'.
It also defines an alias for the XT_BPF_MODE_FD_PINNED mode, named
XT_BPF_MODE_PATH_PINNED, to better reflect the fact that the user is
expected to provide the path of the pinned object.
Existing XT_BPF_MODE_FD_ELF behavior (non-pinned fd mode) is preserved.
References: [1] https://marc.info/?l=netfilter-devel&m=150564724607440&w=2
[2] https://marc.info/?l=netfilter-devel&m=150575727129880&w=2
Reported-by: Rafael Buchbinder <rafi@rbk.ms>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The event handler in the virmidi sequencer code takes a read-lock for
the linked list traverse, while it's calling snd_seq_dump_var_event()
in the loop. The latter function may expand the user-space data
depending on the event type. It eventually invokes copy_from_user(),
which might be a potential dead-lock.
The sequencer core guarantees that the user-space data is passed only
with atomic=0 argument, but snd_virmidi_dev_receive_event() ignores it
and always takes read-lock(). For avoiding the problem above, this
patch introduces rwsem for non-atomic case, while keeping rwlock for
atomic case.
Also while we're at it: the superfluous irq flags is dropped in
snd_virmidi_input_open().
Reported-by: Jia-Ju Bai <baijiaju1990@163.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull SCSI fixes from James Bottomley:
- a couple of serious fixes: use after free and blacklist for WRITE
SAME
- one error leg fix: write_pending failure
- one user experience problem: do not override max_sectors_kb
- one minor unused function removal
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvscsis: Fix write_pending failure path
scsi: libiscsi: Remove iscsi_destroy_session
scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
scsi: sd: Do not override max_sectors_kb sysfs setting
scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
Pull watchddog clean-up and fixes from Thomas Gleixner:
"The watchdog (hard/softlockup detector) code is pretty much broken in
its current state. The patch series addresses this by removing all
duct tape and refactoring it into a workable state.
The reasons why I ask for inclusion that late in the cycle are:
1) The code causes lockdep splats vs. hotplug locking which get
reported over and over. Unfortunately there is no easy fix.
2) The risk of breakage is minimal because it's already broken
3) As 4.14 is a long term stable kernel, I prefer to have working
watchdog code in that and the lockdep issues resolved. I wouldn't
ask you to pull if 4.14 wouldn't be a LTS kernel or if the
solution would be easy to backport.
4) The series was around before the merge window opened, but then got
delayed due to the UP failure caused by the for_each_cpu()
surprise which we discussed recently.
Changes vs. V1:
- Addressed your review points
- Addressed the warning in the powerpc code which was discovered late
- Changed two function names which made sense up to a certain point
in the series. Now they match what they do in the end.
- Fixed a 'unused variable' warning, which got not detected by the
intel robot. I triggered it when trying all possible related config
combinations manually. Randconfig testing seems not random enough.
The changes have been tested by and reviewed by Don Zickus and tested
and acked by Micheal Ellerman for powerpc"
* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
watchdog/core: Put softlockup_threads_initialized under ifdef guard
watchdog/core: Rename some softlockup_* functions
powerpc/watchdog: Make use of watchdog_nmi_probe()
watchdog/core, powerpc: Lock cpus across reconfiguration
watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
watchdog/hardlockup/perf: Cure UP damage
watchdog/hardlockup: Clean up hotplug locking mess
watchdog/hardlockup/perf: Simplify deferred event destroy
watchdog/hardlockup/perf: Use new perf CPU enable mechanism
watchdog/hardlockup/perf: Implement CPU enable replacement
watchdog/hardlockup/perf: Implement init time detection of perf
watchdog/hardlockup/perf: Implement init time perf validation
watchdog/core: Get rid of the racy update loop
watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
watchdog/sysctl: Clean up sysctl variable name space
watchdog/sysctl: Get rid of the #ifdeffery
watchdog/core: Clean up header mess
watchdog/core: Further simplify sysctl handling
watchdog/core: Get rid of the thread teardown/setup dance
...
Pull device mapper fixes from Mike Snitzer:
- a stable fix for the alignment of the event number reported at the
end of the 'DM_LIST_DEVICES' ioctl.
- a couple stable fixes for the DM crypt target.
- a DM raid health status reporting fix.
* tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix incorrect status output at the end of a "recover" process
dm crypt: reject sector_size feature if device length is not aligned to it
dm crypt: fix memory leak in crypt_ctr_cipher_old()
dm ioctl: fix alignment of event number in the device list
Pull sound fixes from Takashi Iwai:
"A collection of small fixes, mostly with stable ones:
- X32 ABI fix for PCM; likely not so many people suffer from it, but
still better to fix
- Two minor kernel warning fixes on USB audio devices spotted by
syzkaller
- Regression fix of echoaudio due to its inconsistent dimension
- Fix for HBR support on Intel DP audio, on some recent chips
- USB-audio quirk for yet another Plantronics devices
- Fix for potential double-fetch in ASIHPI FIFO queue"
* tag 'sound-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usx2y: Suppress kernel warning at page allocation failures
Revert "ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members"
ALSA: usb-audio: Check out-of-bounds access by corrupted buffer descriptor
ALSA: pcm: Fix structure definition for X32 ABI
ALSA: usb-audio: Add sample rate quirk for Plantronics C310/C520-M
ALSA: hda - program ICT bits to support HBR audio
ALSA: asihpi: fix a potential double-fetch bug when copying puhm
ALSA: compress: Remove unused variable
Pull networking fixes from David Miller:
1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
from Sara Sharon.
2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
Kasiviswanathan.
3) Fix session and tunnel release races in l2tp, from Guillaume Nault
and Sabrina Dubroca.
4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.
5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
cap check, invalid memory access in IPoIB support, etc.)
6) tun_get_user() should bail if skb->len is zero, from Alexander
Potapenko.
7) Fix RCU lookups in inetpeer, from Eric Dumazet.
8) Fix locking in packet_do_bund().
9) Handle cb->start() error properly in netlink dump code, from Jason
A. Donenfeld.
10) Handle multicast properly in UDP socket early demux code. From Paolo
Abeni.
11) Several erspan bug fixes in ip_gre, from Xin Long.
12) Fix use-after-free in socket filter code, in order to handle the
fact that listener lock is no longer taken during the three-way TCP
handshake. From Eric Dumazet.
13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.
14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: 8021q: skip packets if the vlan is down
bpf: fix bpf_tail_call() x64 JIT
net: stmmac: dwmac-rk: Add RK3128 GMAC support
rndis_host: support Novatel Verizon USB730L
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
mlxsw: spectrum_router: Track RIF of IPIP next hops
mlxsw: spectrum_router: Move VRF refcounting
net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
net: mvpp2: Fix clock resource by adding an optional bus clock
r8152: add Linksys USB3GIGV1 id
l2tp: fix l2tp_eth module loading
ip_gre: erspan device should keep dst
ip_gre: set tunnel hlen properly in erspan_tunnel_init
ip_gre: check packet length and mtu correctly in erspan_xmit
ip_gre: get key from session_id correctly in erspan_rcv
tipc: use only positive error codes in messages
ppp: fix __percpu annotation
udp: perform source validation for mcast early demux
IPv4: early demux can return an error code
...
Pull ARM SoC fixes from Olof Johansson:
"Our first batch of fixes this release cycle, unfortunately a bit
noisier than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents
between the old format and the new. This could arguably be moved to
the next merge window but it also seemed relatively harmless to
include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these
kind of changes. The platform is actively being upstreamed so
there's a few things in flight, we've seen this happen before and
sometimes it's hard to catch in time.
Besides that there is the usual mix of minor fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
ARM: defconfig: update Gemini defconfig
ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARM: dts: da850-evm: add serial and ethernet aliases
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
...
This patch addresses the following bugs in the current rescind handling code:
1. Fixes a race condition where we may be invoking hv_process_channel_removal()
on an already freed channel.
2. Prevents indefinite wait when rescinding sub-channels by correctly setting
the probe_complete state.
I would like to thank Dexuan for patiently reviewing earlier versions of this
patch and identifying many of the issues fixed here.
Greg, please apply this to 4.14-final.
Fixes: '54a66265d675 ("Drivers: hv: vmbus: Fix rescind handling")'
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Cc: stable@vger.kernel.org # (4.13 and above)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rework of the core hotplug code triggers the WARN_ON in start_wd_cpu()
on powerpc because it is called multiple times for the boot CPU.
The first call is via:
start_wd_on_cpu+0x80/0x2f0
watchdog_nmi_reconfigure+0x124/0x170
softlockup_reconfigure_threads+0x110/0x130
lockup_detector_init+0xbc/0xe0
kernel_init_freeable+0x18c/0x37c
kernel_init+0x2c/0x160
ret_from_kernel_thread+0x5c/0xbc
And then again via the CPU hotplug registration:
start_wd_on_cpu+0x80/0x2f0
cpuhp_invoke_callback+0x194/0x620
cpuhp_thread_fun+0x7c/0x1b0
smpboot_thread_fn+0x290/0x2a0
kthread+0x168/0x1b0
ret_from_kernel_thread+0x5c/0xbc
This can be avoided by setting up the cpu hotplug state with nocalls and
move the initialization to the watchdog_nmi_probe() function. That
initializes the hotplug callbacks without invoking the callback and the
following core initialization function then configures the watchdog for the
online CPUs (in this case CPU0) via softlockup_reconfigure_threads().
Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
In may, Steven sent a patch deleting the bounce buffer handling
and the CONFIG_MMC_BLOCK_BOUNCE option.
I chose the less invasive path of making it a runtime config
option, and we merged that successfully for kernel v4.12.
The code is however just standing in the way and taking up
space for seemingly no gain on any systems in wide use today.
Pierre says the code was there to improve speed on TI SDHCI
controllers on certain HP laptops and possibly some Ricoh
controllers as well. Early SDHCI controllers lacked the
scatter-gather feature, which made software bounce buffers
a significant speed boost.
We are clearly talking about the list of SDHCI PCI-based
MMC/SD card readers found in the pci_ids[] list in
drivers/mmc/host/sdhci-pci-core.c.
The TI SDHCI derivative is not supported by the upstream
kernel. This leaves the Ricoh.
What we can however notice is that the x86 defconfigs in the
kernel did not enable CONFIG_MMC_BLOCK_BOUNCE option, which
means that any such laptop would have to have a custom
configured kernel to actually take advantage of this
bounce buffer speed-up. It simply seems like there was
a speed optimization for the Ricoh controllers that noone
was using. (I have not checked the distro defconfigs but
I am pretty sure the situation is the same there.)
Bounce buffers increased performance on the OMAP HSMMC
at one point, and was part of the original submission in
commit a45c6cb816 ("[ARM] 5369/1: omap mmc: Add new
omap hsmmc controller for 2430 and 34xx, v3")
This optimization was removed in
commit 0ccd76d4c2 ("omap_hsmmc: Implement scatter-gather
emulation")
which found that scatter-gather emulation provided even
better performance.
The same was introduced for SDHCI in
commit 2134a922c6 ("sdhci: scatter-gather (ADMA) support")
I am pretty positively convinced that software
scatter-gather emulation will do for any host controller what
the bounce buffers were doing. Essentially, the bounce buffer
was a reimplementation of software scatter-gather-emulation in
the MMC subsystem, and it should be done away with.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Steven J. Hill <Steven.Hill@cavium.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Suggested-by: Steven J. Hill <Steven.Hill@cavium.com>
Suggested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reset controller fixes for v4.14
- Remove misleading HSDK v1 suffix, as there is no v2 planned
- Add missing DT binding documentation for HSDK reset driver
- Fix HSDK reset driver dependencies
* tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux:
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
Signed-off-by: Olof Johansson <olof@lixom.net>
