When reading pinconf-pins from debugfs it fails to get the configured pull
type on RK3568, "unsupported pinctrl type" error messages is also reported.
Fix this by adding support for RK3568 in rockchip_get_pull, including a
reverse of the pull-up value swap applied in rockchip_set_pull so that
pull-up is correctly reported in pinconf-pins.
Also update the workaround comment to reflect affected pins, GPIO0_D3-D6.
Fixes: c0dadc0e47 ("pinctrl: rockchip: add support for rk3568")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20230110172955.1258840-1-jonas@kwiboo.se
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sppctl_gpio_inv_get is only used from the debugfs code inside
of an #ifdef, so we get a warning without that:
drivers/pinctrl/sunplus/sppctl.c:393:12: error: 'sppctl_gpio_inv_get' defined but not used [-Werror=unused-function]
393 | static int sppctl_gpio_inv_get(struct gpio_chip *chip, unsigned int offset)
| ^~~~~~~~~~~~~~~~~~~
Replace the #ifdef with an IS_ENABLED() check that avoids the warning.
Fixes: aa74c44be1 ("pinctrl: Add driver for Sunplus SP7021")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20221215163822.542622-1-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"The two large chunks is the header clean-up from Andy and the Qualcomm
DT bindings clean-up from Krzysztof. Each which could give rise to
conflicts, but I haven't seen any.
The YAML conversions happening around the device tree is the biggest
item in the series and is the result of Rob Herrings ambition to
autovalidate these trees against strict schemas and it is paying off
in lots of bugs found and ever prettier device trees. Sooner or later
the transition will be complete, Krzysztof is fixing up all of the
Qualcomm stuff, which is pretty voluminous.
Core changes:
- minor but nice and important documentation clean-ups
New drivers:
- subdriver for the Qualcomm SDM670 SoC
- subdriver for the Intel Moorefield SoC
- trivial support for the NXP Freescale i.MXRT1170 SoC
Other changes and improvements
- major clean-up of the Qualcomm pin control device tree bindings by
Krzysztof
- major header clean-up by Andy
- some immutable irqchip clean-up for the Actions Semiconductor and
Nuvoton drivers
- GPIO helpers for The Cypress cy8c95x0 driver
- bias handling in the Mediatek MT7986 driver
- remove the unused pins-are-numbered concept that never flew"
* tag 'pinctrl-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (231 commits)
pinctrl: thunderbay: fix possible memory leak in thunderbay_build_functions()
dt-bindings: pinctrl: st,stm32: Deprecate pins-are-numbered
dt-bindings: pinctrl: mediatek,mt65xx: Deprecate pins-are-numbered
pinctrl: stm32: Remove check for pins-are-numbered
pinctrl: mediatek: common: Remove check for pins-are-numbered
pinctrl: qcom: remove duplicate included header files
pinctrl: sunxi: d1: Add CAN bus pinmuxes
pinctrl: loongson2: Fix some const correctness
pinctrl: pinconf-generic: add missing of_node_put()
pinctrl: intel: Enumerate PWM device when community has a capability
pwm: lpss: Rename pwm_lpss_probe() --> devm_pwm_lpss_probe()
pwm: lpss: Allow other drivers to enable PWM LPSS
pwm: lpss: Include headers we are the direct user of
pwm: lpss: Rename MAX_PWMS --> LPSS_MAX_PWMS
pwm: Add a stub for devm_pwmchip_add()
pinctrl: k210: call of_node_put()
pinctrl: starfive: Use existing variable gpio
dt-bindings: pinctrl: semtech,sx150xq: fix match patterns for 16 GPIOs matching
pinconf-generic: fix style issues in pin_config_param doc
pinctrl: pinctrl-loongson2: fix Kconfig dependency
...
The thunderbay_add_functions() will free memory of thunderbay_funcs
when everything is ok, but thunderbay_funcs will not be freed when
thunderbay_add_functions() fails, then there will be a memory leak,
so we need to add kfree() when thunderbay_add_functions() fails to
fix it.
In addition, doing some cleaner works, moving kfree(funcs) from
thunderbay_add_functions() to thunderbay_build_functions().
Fixes: 12422af819 ("pinctrl: Add Intel Thunder Bay pinctrl driver")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20221129120126.1567338-1-cuigaosheng1@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v6.2-2
* Enable PWM feature on Intel pin control IPs
The following is an automated git shortlog grouped by driver:
intel:
- Enumerate PWM device when community has a capability
pwm:
- lpss: Rename pwm_lpss_probe() --> devm_pwm_lpss_probe()
- lpss: Allow other drivers to enable PWM LPSS
- lpss: Include headers we are the direct user of
- lpss: Rename MAX_PWMS --> LPSS_MAX_PWMS
- Add a stub for devm_pwmchip_add()
The kernel robot using sparse is complaining like this:
drivers/pinctrl/pinctrl-loongson2.c:212:21: sparse:
sparse: incorrect type in argument 1 (different address spaces) @@
expected void const volatile [noderef] __iomem *addr @@
got void *[noderef] __iomem reg @@
(...)
I think the problem is simply that the register base is defined
as void * __iomem instead of void __iomem * and this is because
of the way const correctness works with pointer infix order.
Fix it up. I think.
Reported-by: kernel test robot <lkp@intel.com>
Cc: zhanghongchen <zhanghongchen@loongson.cn>
Cc: Yinbo Zhu <zhuyinbo@loongson.cn>
Fixes: f73f88acbc ("pinctrl: pinctrl-loongson2: add pinctrl driver support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a possibility of dividing by zero due to the pcs->bits_per_pin
if pcs->fmask() also has a value of zero and called fls
from asm-generic/bitops/builtin-fls.h or arch/x86/include/asm/bitops.h.
The function pcs_probe() has the branch that assigned to fmask 0 before
pcs_allocate_pin_table() was called
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221117123034.27383-1-korotkov.maxim.s@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If CONFIG_PINCTRL_LOONGSON2=y and CONFIG_OF is not set,
gcc complained about undefined reference:
drivers/pinctrl/pinctrl-loongson2.o: In function `pinconf_generic_dt_node_to_map_all':
pinctrl-loongson2.c:(.text+0x1c4): undefined reference to
`pinconf_generic_dt_node_to_map'
To fix this error, add depends on OF to
config PINCTRL_LOONGSON2.
Fixes: f73f88acbc ("pinctrl: pinctrl-loongson2: add pinctrl driver support")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Link: https://lore.kernel.org/r/20221121132608.230645-1-renzhijie2@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v6.2-1
* Add Intel Moorefield pin control driver
* Deduplicate COMMUNITY() macro in the Intel pin control drivers
* Switch Freescale GPIO driver to use fwnode instead of of_node
* Miscellaneous clenups here and there
The following is an automated git shortlog grouped by driver:
alderlake:
- Deduplicate COMMUNITY macro code
cannonlake:
- Deduplicate COMMUNITY macro code
device property:
- Introduce fwnode_device_is_compatible() helper
icelake:
- Deduplicate COMMUNITY macro code
intel:
- Add Intel Moorefield pin controller support
- Use temporary variable for struct device
- Use str_enable_disable() helper
merrifield:
- Use temporary variable for struct device
qcom:
- lpass-lpi: Add missed bitfield.h
soc:
- fsl: qe: Switch to use fwnode instead of of_node
sunrisepoint:
- Deduplicate COMMUNITY macro code
tigerlake:
- Deduplicate COMMUNITY macro code
Since commit 502df79b86 ("gpiolib: Warn on drivers still using
static gpiobase allocation") in gpio/for-next, one or more warnings are
printed during boot on systems where the pin controller also provides
GPIO functionality:
gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
Fix this for ARM-based SH/R-Mobile SoCs by:
1. Taking into account a non-zero GPIO base in the various GPIO chip
callbacks,
2. Switching to dynamic allocation of the GPIO base when support for
legacy function GPIOs is not enabled.
On SuperH SoCs using legacy function GPIOs, the GPIO bases of the GPIO
controller and the GPIO function controller must not be changed, as all
board files rely on the fixed GPIO_* and GPIO_FN_* definitions provided
by the various <cpu/sh*.h> header files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/df2cf30ac4c3cbee726799f32b727c1ebe62819c.1668000684.git.geert+renesas@glider.be
The kernel test robot complains that in certain combinations
when building the Mediatek drivers as modules we lack some
debounce table symbols, so export them.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1ff91f9d2 ("pinctrl: mediatek: Fix EINT pins input debounce time configuration")
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The External Interrupt Controller (EINTC) on all of the supported
MediaTek SoCs does support input debouncing, but not all of them
index the debounce time values (DBNC_SETTING registers) the same way.
Before this change, in some cases, as an example, requesting a debounce
time of 16 milliseconds would mistakenly set the relative DBNC_SETTING
register to 0x2, resulting in a way shorter debounce time of 500uS.
To fix the aforementioned issue, define three different debounce_time
arrays, reflecting the correct register index for each value and for
each register index variant, and make sure that each SoC pinctrl
driver uses the right one.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221111094106.18486-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra194 has two separate instances of the pin controller, one called
AON (in the always-on domain) and another called "main". Instead of
treating them as a single pin controller, split them up into two
separate controllers. Doing so allows the mapping between the pinmux
and GPIO controllers to be trivial identity mappings and more cleanly
separates the AON from the main IP blocks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221104142345.1562750-4-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here is the BUG report by KASAN about null pointer dereference:
BUG: KASAN: null-ptr-deref in strcmp+0x2e/0x50
Read of size 1 at addr 0000000000000000 by task python3/2640
Call Trace:
strcmp
__of_find_property
of_find_property
pinctrl_dt_to_map
kasprintf() would return NULL pointer when kmalloc() fail to allocate.
So directly return ENOMEM, if kasprintf() return NULL pointer.
Fixes: 57291ce295 ("pinctrl: core device tree mapping table parsing support")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Link: https://lore.kernel.org/r/20221110082056.2014898-1-zengheng4@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In pinctrl-paris we're calling the .bias_set_combo() callback when we
are asked to set the pin bias to either pull up/down or pull disable.
On newer platforms, this callback is mtk_pinconf_bias_set_combo(),
located in pinctrl-mtk-common-v2.c: this will check the "pull type"
assigned to the requested pin and in case said pin's pull type is
MTK_PULL_PU_PD_RSEL_TYPE, this function will set RSEL first, PUPD
last, which is fine.
The issue comes when we're requesting PIN_CONFIG_BIAS_DISABLE, as
this does *not* require setting RSEL but only PU_PD: in this case,
the arg is MTK_DISABLE (zero), which is not a supported RSEL, due
to which function mtk_pinconf_bias_set_rsel() returns a failure;
because of that, mtk_pinconf_bias_set_pu_pd() is never called,
hence the pin bias is never set to DISABLE.
To fix this issue, add a check to mtk_pinconf_bias_set_rsel(): if
we are entering that function with no pullup requested and at the
same time the arg is MTK_DISABLE, this means that we're trying to
disable pin bias, hence it's safe to return cleanly without ever
setting any RSEL register.
This makes mtk_pinconf_bias_set_combo() happy, going on with setting
the PU_PD registers, which is the only action to actually take to
disable bias on a pin/pingroup.
Fixes: fb34a9ae38 ("pinctrl: mediatek: support rsel feature")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221104105605.33720-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl support for Intel Moorefield. The IP block
which is called Family-Level Interface Shim is a separate entity in SoC.
The GPIO driver, which supports this pinctrl interface, will be
submitted separately.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The mux routes are incomplete for the PX30. This was discovered because
we had a HW design using cif-clkoutm1 with the correct pinmux in the
Device Tree but the clock would still not work.
There are actually two muxing required: the pin muxing (performed by the
usual Device Tree pinctrl nodes) and the "function" muxing (m0 vs m1;
performed by the mux routing inside the driver). The pin muxing was
correct but the function muxing was not.
This adds the missing pins and their configuration for the mux routes
that are already specified in the driver.
Note that there are some "conflicts": it is possible *in Device Tree* to
(attempt to) mux the pins for e.g. clkoutm1 and clkinm0 at the same time
but this is actually not possible in hardware (because both share the
same bit for the function muxing). Since it is an impossible hardware
design, it is not deemed necessary to prevent the user from attempting
to "misconfigure" the pins/functions.
Fixes: 87065ca9b8 ("pinctrl: rockchip: Add pinctrl support for PX30")
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20221017-upstream-px30-cif-clkoutm1-v1-0-4ea1389237f7@theobroma-systems.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Previously the cleanup change dropped the bitfield.h from the
pinctrl-lpass-lpi.h, since it's not used there, but forgot to
re-instantiate it in the C-file, where users are located.
Fix this by adding missed bitfield.h to the C-file.
Fixes: aa9430f8a6 ("pinctrl: qcom: Add missing header(s)")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
