Use struct ice_adapter to hold shared PTP data and control PTP
related actions instead of auxbus. This allows significant code
simplification and faster access to the container fields used in
the PTP support code.
Move the PTP port list to the ice_adapter container to simplify
the code and avoid race conditions which could occur due to the
synchronous nature of the initialization/access and
certain memory saving can be achieved by moving PTP data into
the ice_adapter itself.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add ice_get_ctrl_ptp() wrapper to simplify the PTP support code
in the functions that do not use ctrl_pf directly.
Add the control PF pointer to struct ice_adapter
Rearrange fields in struct ice_adapter
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
PTP pins assignment and their related SDPs (Software Definable Pins) are
currently hardcoded.
Fix that by reading NVM section instead on products supporting this,
which are E810 products.
If SDP section is not defined in NVM, the driver continues to use the
hardcoded table.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cache original PTP GPIO requests instead of saving each parameter in
internal structures for periodic output or external timestamp request.
Factor out all periodic output register writes from ice_ptp_cfg_clkout
to a separate function to improve readability.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
Pull networking updates from Jakub Kicinski:
"Not much excitement - a handful of large patchsets (devmem among them)
did not make it in time.
Core & protocols:
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT
- Use flex array for netdevice priv area, ensure its cache alignment
- Add a sysctl knob to allow user to specify a default rto_min at
socket init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful
- Support scheduling transmission of packets based on CLOCK_TAI
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned
off using cpusets
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address
- Allow configuration of multipath hash seed, to both allow
synchronizing hashing of two routers, and preventing partial
accidental sync
- Improve TCP compliance with RFC 9293 for simultaneous connect()
- Support sending NAT keepalives in IPsec ESP in UDP states.
Userspace IKE daemon had to do this before, but the kernel can
better keep track of it
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled
- Introduce IPPROTO_SMC for selecting SMC when socket is created
- Allow UDP GSO transmit from devices with no checksum offload
- openvswitch: add packet sampling via psample, separating the
sampled traffic from "upcall" packets sent to user space for
forwarding
- nf_tables: shrink memory consumption for transaction objects
Things we sprinkled into general kernel code:
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver for
QCA6390) [ Already merged separately - Linus ]
- Add IRQ information in sysfs for auxiliary bus
- Introduce guard definition for local_lock
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures
BPF:
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered
- Add new kfuncs for a generic, open-coded bits iterator
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head
- Support resilient split BTF which cuts down on duplication and
makes BTF as compact as possible WRT BTF from modules
- Add support for dumping kfunc prototypes from BTF which enables
both detecting as well as dumping compilable prototypes for kfuncs
- riscv64 BPF JIT improvements in particular to add 12-argument
support for BPF trampolines and to utilize bpf_prog_pack for the
latter
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs
Driver API:
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits
- Track additional RSS contexts in the core, make sure configuration
changes don't break them
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated
ESP data paths
- Support updating firmware on SFP modules
Tests and tooling:
- mptcp: use net/lib.sh to manage netns
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints
- openvswitch: make test self-contained (don't depend on OvS CLI
tools)
Drivers:
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead and
skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps to
catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead
of in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"
* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits)
eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering"
tcp: Replace strncpy() with strscpy()
wifi: ath12k: fix build vs old compiler
tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child().
eth: fbnic: Write the TCAM tables used for RSS control and Rx to host
eth: fbnic: Add L2 address programming
eth: fbnic: Add basic Rx handling
eth: fbnic: Add basic Tx handling
eth: fbnic: Add link detection
eth: fbnic: Add initial messaging to notify FW of our presence
eth: fbnic: Implement Rx queue alloc/start/stop/free
eth: fbnic: Implement Tx queue alloc/start/stop/free
eth: fbnic: Allocate a netdevice and napi vectors with queues
eth: fbnic: Add FW communication mechanism
eth: fbnic: Add message parsing for FW messages
eth: fbnic: Add register init to set PCIe/Ethernet device config
eth: fbnic: Allocate core device specific structures and devlink interface
eth: fbnic: Add scaffolding for Meta's NIC driver
PCI: Add Meta Platforms vendor ID
net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK
...
Pull clocksource/event driver updates from Daniel Lezcano:
- Remove unnecessary local variables initialization as they will be
initialized in the code path anyway right after on the ARM arch
timer and the ARM global timer (Li kunyu)
- Fix a race condition in the interrupt leading to a deadlock on the
SH CMT driver. Note that this fix was not tested on the platform
using this timer but the fix seems reasonable enough to be picked
confidently (Niklas Söderlund)
- Increase the rating of the gic-timer and use the configured width
clocksource register on the MIPS architecture (Jiaxun Yang)
- Add the DT bindings for the TMU on the Renesas platforms (Geert
Uytterhoeven)
- Add the DT bindings for the SOPHGO SG2002 clint on RiscV (Thomas
Bonnefille)
- Add the rtl-otto timer driver along with the DT bindings for the
Realtek platform (Chris Packham)
Link: https://lore.kernel.org/all/91cd05de-4c5d-4242-a381-3b8a4fe6a2a2@linaro.org
The driver receives requests for configuring pins via the .enable
callback of the PTP clock object. These requests come into the driver
with flags which modify the requested behavior from userspace. Current
implementation in ice does not reject flags that it doesn't support.
This causes the driver to incorrectly apply requests with such flags as
PTP_PEROUT_DUTY_CYCLE, or any future flags added by the kernel which it
is not yet aware of.
Fix this by properly validating flags in both ice_ptp_cfg_perout and
ice_ptp_cfg_extts. Ensure that we check by bit-wise negating supported
flags rather than just checking and rejecting known un-supported flags.
This is preferable, as it ensures better compatibility with future
kernels.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240702171459.2606611-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice_ptp_extts_event() function can race with ice_ptp_release() and
result in a NULL pointer dereference which leads to a kernel panic.
Panic occurs because the ice_ptp_extts_event() function calls
ptp_clock_event() with a NULL pointer. The ice driver has already
released the PTP clock by the time the interrupt for the next external
timestamp event occurs.
To fix this, modify the ice_ptp_extts_event() function to check the
PTP state and bail early if PTP is not ready.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240702171459.2606611-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extts events are disabled and enabled by the application ts2phc.
However, in case where the driver is removed when the application is
running, a specific extts event remains enabled and can cause a kernel
crash.
As a side effect, when the driver is reloaded and application is started
again, remaining extts event for the channel from a previous run will
keep firing and the message "extts on unexpected channel" might be
printed to the user.
To avoid that, extts events shall be disabled when PTP is released.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240702171459.2606611-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ice_ptp_cfg_clkout(), the ice driver needs to calculate the nearest next
second of a current time value specified in nanoseconds. It implements this
using div64_u64, because the time value is a u64. It could use div_u64
since NSEC_PER_SEC is smaller than 32-bits.
Ideally this would be implemented directly with roundup(), but that can't
work on all platforms due to a division which requires using the specific
macros and functions due to platform restrictions, and to ensure that the
most appropriate and fast instructions are used.
The kernel doesn't currently provide any 64-bit equivalents for doing
roundup. Attempting to use roundup() on a 32-bit platform will result in a
link failure due to not having a direct 64-bit division.
The closest equivalent for this is DIV64_U64_ROUND_UP, which does a
division always rounding up. However, this only computes the division, and
forces use of the div64_u64 in cases where the divisor is a 32bit value and
could make use of div_u64.
Introduce DIV_U64_ROUND_UP based on div_u64, and then use it to implement
roundup_u64 which takes a u64 input value and a u32 rounding value.
The name roundup_u64 matches the naming scheme of div_u64, and future
patches could implement roundup64_u64 if they need to round by a multiple
that is greater than 32-bits.
Replace the logic in ice_ptp.c which does this equivalent with the newly
added roundup_u64.
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240607-next-2024-06-03-intel-next-batch-v3-2-d1470cee3347@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
>From FW/HW perspective, 2 port topology in E825C devices requires
merging of 2 port mapping internally and breakout mapping externally.
As a consequence, it requires different port numbering from PTP code
perspective.
For that topology, pf_id can not be used to index PTP ports. Even if
the 2nd port is identified as port with pf_id = 1, all PHY operations
need to be performed as it was port 2. Thus, special mapping is needed
for the 2nd port.
This change adds detection of 2x50G topology and applies 'custom'
mapping on the 2nd port.
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-next-2024-05-28-ptp-refactors-v1-11-c082739bb6f6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP hardware semaphore (PFTSYN_SEM) is used to synchronize
operations that program the PTP timers. The operations involve issuing
commands to the sideband queue. The E810 does not have a hardware
sideband queue, so the admin queue is used. The admin queue is slow.
I have observed delays in hundreds of milliseconds waiting for
ice_sq_done.
When phc2sys reads the time from the ice PTP clock and PFTSYN_SEM is
held by a task performing one of the slow operations, ice_ptp_lock can
easily time out. phc2sys gets -EBUSY and the kernel prints:
ice 0000:XX:YY.0: PTP failed to get time
These messages appear once every few seconds, causing log spam.
The E810 datasheet recommends an algorithm for reading the upper 64 bits
of the GLTSYN_TIME register. It matches what's implemented in
ice_ptp_read_src_clk_reg. It is robust against wrap-around, but not
necessarily against the concurrent setting of the register (with
GLTSYN_CMD_{INIT,ADJ}_TIME commands). Perhaps that's why
ice_ptp_gettimex64 also takes PFTSYN_SEM.
The race with time setters can be prevented without relying on the PTP
hardware semaphore. Using the "ice_adapter" from the previous patch,
we can have a common spinlock for the PFs that share the clock hardware.
It will protect the reading and writing to the GLTSYN_TIME register.
The writing is performed indirectly, by the hardware, as a result of
the driver writing GLTSYN_CMD_SYNC in ice_ptp_exec_tmr_cmd. I wasn't
sure if the ice_flush there is enough to make sure GLTSYN_TIME has been
updated, but it works well in my testing.
My test code can be seen here:
https://gitlab.com/mschmidt2/linux/-/commits/ice-ptp-host-side-lock-10
It consists of:
- kernel threads reading the time in a busy loop and looking at the
deltas between consecutive values, reporting new maxima.
- a shell script that sets the time repeatedly;
- a bpftrace probe to produce a histogram of the measured deltas.
Without the spinlock ptp_gltsyn_time_lock, it is easy to see tearing.
Deltas in the [2G, 4G) range appear in the histograms.
With the spinlock added, there is no tearing and the biggest delta I saw
was in the range [1M, 2M), that is under 2 ms.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver currently attempts to destroy and re-initialize the Tx
timestamp tracker during the reset flow. The release of the Tx tracker
only happened during CORE reset or GLOBAL reset. The ice_ptp_rebuild()
function always calls the ice_ptp_init_tx function which will allocate
a new tracker data structure, resulting in memory leaks during PF reset.
Certainly the driver should not be allocating a new tracker without
removing the old tracker data, as this results in a memory leak.
Additionally, there's no reason to remove the tracker memory during a
reset. Remove this logic from the reset and rebuild flow. Instead of
releasing the Tx tracker, flush outstanding timestamps just before we
reset the PHY timestamp block in ice_ptp_cfg_phy_interrupt().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_reset() function uses a goto to skip past clock owner
operations if performing a PF reset or if the device is not the clock
owner. This is a bit confusing. Factor this out into
ice_ptp_rebuild_owner() instead.
The ice_ptp_reset() function is called by ice_rebuild() to restore PTP
functionality after a device reset. Follow the convention set by the
ice_main.c file and rename this function to ice_ptp_rebuild(), in the
same way that we have ice_prepare_for_reset() and
ice_ptp_prepare_for_reset().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_tx_cfg_intr() function sends a control queue message to
configure the PHY timestamp interrupt block. This is a very similar name
to a function which is used to configure the MAC Other Interrupt Cause
Enable register.
Rename this function to ice_ptp_cfg_phy_interrupt in order to make it
more obvious to the reader what action it performs, and distinguish it
from other similarly named functions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
E810 hardware does not have a Tx timestamp ready bitmap. Don't check
has_ready_bitmap in E810-specific functions.
Add has_ready_bitmap check in ice_ptp_process_tx_tstamp() to stop
relying on the fact that ice_get_phy_tx_tstamp_ready() returns all 1s.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tx->verify_cached flag is used to inform the Tx timestamp tracking
code whether it needs to verify the cached Tx timestamp value against
a previous captured value. This is necessary on E810 hardware which does
not have a Tx timestamp ready bitmap.
In addition, we currently rely on the fact that the
ice_get_phy_tx_tstamp_ready() function returns all 1s for E810 hardware.
Instead of introducing a brand new flag, rename and verify_cached to
has_ready_bitmap, inverting the relevant checks.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_prepare_for_reset() and ice_ptp_reset() functions currently
check the pf->flags ICE_FLAG_PFR_REQ bit to determine if the current
reset is a PF reset or not.
This is problematic, because it is possible that a PF reset and a higher
level reset (CORE reset, GLOBAL reset, EMP reset) are requested
simultaneously. In that case, the driver performs the highest level
reset requested. However, the ICE_FLAG_PFR_REQ flag will still be set.
The main driver reset functions take an enum ice_reset_req indicating
which reset is actually being performed. Pass this data into the PTP
functions and rely on this instead of relying on the driver flags.
This ensures that the PTP code performs the proper level of reset that
the driver is actually undergoing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce new capability - Low Latency Timestamping with Interrupt.
On supported devices, driver can request a single timestamp from FW
without polling the register afterwards. Instead, FW can issue
a dedicated interrupt when the timestamp was read from the PHY register
and its value is available to read from the register.
This eliminates the need of bottom half scheduling, which results in
minimal delay for timestamping.
For this mode, allocate TS indices sequentially, so that timestamps are
always completed in FIFO manner.
Co-developed-by: Yochai Hagvi <yochai.hagvi@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
intel: use bitfield operations
Jesse Brandeburg says:
After repeatedly getting review comments on new patches, and sporadic
patches to fix parts of our drivers, we should just convert the Intel code
to use FIELD_PREP() and FIELD_GET(). It's then "common" in the code and
hopefully future change-sets will see the context and do-the-right-thing.
This conversion was done with a coccinelle script which is mentioned in the
commit messages. Generally there were only a couple conversions that were
"undone" after the automatic changes because they tried to convert a
non-contiguous mask.
Patch 1 is required at the beginning of this series to fix a "forever"
issue in the e1000e driver that fails the compilation test after conversion
because the shift / mask was out of range.
The second patch just adds all the new #includes in one go.
The patch titled: "ice: fix pre-shifted bit usage" is needed to allow the
use of the FIELD_* macros and fix up the unexpected "shifts included"
defines found while creating this series.
The rest are the conversion to use FIELD_PREP()/FIELD_GET(), and the
occasional leXX_{get,set,encode}_bits() call, as suggested by Alex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2023-12-18
This PR is larger than usual and contains changes in various parts
of the kernel.
The main changes are:
1) Fix kCFI bugs in BPF, from Peter Zijlstra.
End result: all forms of indirect calls from BPF into kernel
and from kernel into BPF work with CFI enabled. This allows BPF
to work with CONFIG_FINEIBT=y.
2) Introduce BPF token object, from Andrii Nakryiko.
It adds an ability to delegate a subset of BPF features from privileged
daemon (e.g., systemd) through special mount options for userns-bound
BPF FS to a trusted unprivileged application. The design accommodates
suggestions from Christian Brauner and Paul Moore.
Example:
$ sudo mkdir -p /sys/fs/bpf/token
$ sudo mount -t bpf bpffs /sys/fs/bpf/token \
-o delegate_cmds=prog_load:MAP_CREATE \
-o delegate_progs=kprobe \
-o delegate_attachs=xdp
3) Various verifier improvements and fixes, from Andrii Nakryiko, Andrei Matei.
- Complete precision tracking support for register spills
- Fix verification of possibly-zero-sized stack accesses
- Fix access to uninit stack slots
- Track aligned STACK_ZERO cases as imprecise spilled registers.
It improves the verifier "instructions processed" metric from single
digit to 50-60% for some programs.
- Fix verifier retval logic
4) Support for VLAN tag in XDP hints, from Larysa Zaremba.
5) Allocate BPF trampoline via bpf_prog_pack mechanism, from Song Liu.
End result: better memory utilization and lower I$ miss for calls to BPF
via BPF trampoline.
6) Fix race between BPF prog accessing inner map and parallel delete,
from Hou Tao.
7) Add bpf_xdp_get_xfrm_state() kfunc, from Daniel Xu.
It allows BPF interact with IPSEC infra. The intent is to support
software RSS (via XDP) for the upcoming ipsec pcpu work.
Experiments on AWS demonstrate single tunnel pcpu ipsec reaching
line rate on 100G ENA nics.
8) Expand bpf_cgrp_storage to support cgroup1 non-attach, from Yafang Shao.
9) BPF file verification via fsverity, from Song Liu.
It allows BPF progs get fsverity digest.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (164 commits)
bpf: Ensure precise is reset to false in __mark_reg_const_zero()
selftests/bpf: Add more uprobe multi fail tests
bpf: Fail uprobe multi link with negative offset
selftests/bpf: Test the release of map btf
s390/bpf: Fix indirect trampoline generation
selftests/bpf: Temporarily disable dummy_struct_ops test on s390
x86/cfi,bpf: Fix bpf_exception_cb() signature
bpf: Fix dtor CFI
cfi: Add CFI_NOSEAL()
x86/cfi,bpf: Fix bpf_struct_ops CFI
x86/cfi,bpf: Fix bpf_callback_t CFI
x86/cfi,bpf: Fix BPF JIT call
cfi: Flip headers
selftests/bpf: Add test for abnormal cnt during multi-kprobe attachment
selftests/bpf: Don't use libbpf_get_error() in kprobe_multi_test
selftests/bpf: Add test for abnormal cnt during multi-uprobe attachment
bpf: Limit the number of kprobes when attaching program to multiple kprobes
bpf: Limit the number of uprobes when attaching program to multiple uprobes
bpf: xdp: Register generic_kfunc_set with XDP programs
selftests/bpf: utilize string values for delegate_xxx mount options
...
====================
Link: https://lore.kernel.org/r/20231219000520.34178-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor the ice driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor ice driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Several places I changed to OR into a single variable with |= instead of
using a multi-line statement with trailing OR operators, as it
(subjectively) makes the code clearer.
A local variable vmvf_and_timeout was created and used to avoid multiple
logical ORs being __le16 converted, which shortened some lines and makes
the code cleaner.
Also clean up a couple of places where conversions were made to have the
code read more clearly/consistently.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use previously refactored code and create a function
that allows XDP code to read HW timestamp.
Also, introduce packet context, where hints-related data will be stored.
ice_xdp_buff contains only a pointer to this structure, to avoid copying it
in ZC mode later in the series.
HW timestamp is the first supported hint in the driver,
so also add xdp_metadata_ops.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-6-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Previously, we only needed RX HW timestamp in skb path,
hence all related code was written with skb in mind.
But with the addition of XDP hints via kfuncs to the ice driver,
the same logic will be needed in .xmo_() callbacks.
Put generic process of reading RX HW timestamp from a descriptor
into a separate function.
Move skb-related code into another source file.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-3-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The E822 hardware for Tx timestamping keeps track of how many
outstanding timestamps are still in the PHY memory block. It will not
generate a new interrupt to the MAC until all of the timestamps in the
region have been read.
If somehow all the available data is not read, but the driver has exited
its interrupt routine already, the PHY will not generate a new interrupt
even if new timestamp data is captured. Because no interrupt is
generated, the driver never processes the timestamp data. This state
results in a permanent failure for all future Tx timestamps.
It is not clear how the driver and hardware could enter this state.
However, if it does, there is currently no recovery mechanism.
Add a recovery mechanism via the periodic PTP work thread which invokes
ice_ptp_periodic_work(). Introduce a new check,
ice_ptp_maybe_trigger_tx_interrupt() which checks the PHY timestamp
ready bitmask. If any bits are set, trigger a software interrupt by
writing to PFINT_OICR.
Once triggered, the main timestamp processing thread will read through
the PHY data and clear the outstanding timestamp data. Once cleared, new
data should trigger interrupts as expected.
This should allow recovery from such a state rather than leaving the
device in a state where we cannot process Tx timestamps.
It is possible that this function checks for timestamp data
simultaneously with the interrupt, and it might trigger additional
unnecessary interrupts. This will cause a small amount of additional
processing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During reset, TX_TSYN interrupt should be processed as it may process
timestamps in brief moments before and after reset.
Timestamping should be enabled on VSIs at the end of reset procedure.
On ice_get_phy_tx_tstamp_ready error, interrupt should not be rearmed
because error only happens on resets.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.
This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.
This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.
Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.
Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:
1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()
2) ice_ptp_restore_timestamp_mode() which calls
ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
issues an immediate TSYN_TX interrupt to ensure that timestamps which
may have occurred during the device reset get processed.
Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.
This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.
With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.
Fixes: 77a781155a ("ice: enable receive hardware timestamping")
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
