Normally, phylib won't notify changes in quick succession. However, as
a result of commit 3e43b903da ("net: phy: Immediately call
adjust_link if only tx_lpi_enabled changes") this is no longer true -
it is now possible that phy_link_down() and phy_link_up() will both
complete before phylink's resolver has run, which means it'll miss that
pl->phy_state.link momentarily became false.
Rename "mac_link_dropped" to be more generic "link_failed" since it will
cover more than the MAC/PCS end of the link failing, and arrange to set
this in phylink_phy_change() if we notice that the PHY reports that the
link is down.
This will ensure that we capture an EEE reconfiguration event.
Fixes: 3e43b903da ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/E1tAtcW-002RBS-LB@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch() statement doesn't sit very well with the preceeding if()
statements, so let's just convert everything to if()s. As a result of
the two preceding commits, there is now only one case in the switch()
statement. Remove the switch statement and reduce the code indentation.
Code reformatting will be in the following commit.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQu-002Fez-AA@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few issues with how SFP PHYs are attached:
a) The phylink_sfp_connect_phy() and phylink_sfp_config_phy() code
validates the configuration three times:
1. To discover the support/advertising masks that the PHY/PCS/MAC
can support in order to select an interface.
2. To validate the selected interface.
3. When the PHY is brought up after being attached, another validation
is done.
This is needlessly complex.
b) The configuration is set prior to the PHY being attached, which
means we don't have the PHY available in phylink_major_config()
for phylink_pcs_neg_mode() to make decisions upon.
We have already added an extra step to validate the selected interface,
so we can now move the attachment and bringup of the PHY earlier,
inside phylink_sfp_config_phy(). This results in the validation at
step 2 above becoming entirely unnecessary, so remove that too.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcb-000c8H-3e@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phylink_parse_fixedlink() wants to preserve the pause, asym_pause and
autoneg bits in pl->supported. Rather than reading the bits into
separate bools, zeroing pl->supported, and then setting them if they
were previously set, use a mask and linkmode_and() to achieve the same
result.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1t3Fh5-000aQi-Nk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With DSA's implementation of the mac_select_pcs() method removed, we
can now remove the detection of mac_select_pcs() implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
When the mac_select_pcs() method is not implemented, there is no way
for pl->pcs to be set to a non-NULL value. This was here to support
the old phylink_set_pcs() method which has been removed a few years
ago. Simplify the code in phylink_validate_mac_and_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
phylink has historically not permitted a PCS to be removed. An attempt
to permit this with phylink_set_pcs() resulted in comments indicating
that there was no need for this. This behaviour has been propagated
forward to the mac_select_pcs() approach as it was believed from these
comments that changing this would be NAK'd.
However, with mac_select_pcs(), it takes more code and thus complexity
to maintain this behaviour, which can - and in this case has - resulted
in a bug. If mac_select_pcs() returns NULL for a particular interface
type, but there is already a PCS in-use, then we skip the pcs_validate()
method, but continue using the old PCS. Also, it wouldn't be expected
behaviour by implementers of mac_select_pcs().
Allow this by removing this old unnecessary restriction.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The function allows for the configuration of a fixed link state for a given
phylink instance. This addition is particularly useful for network devices that
operate with a fixed link configuration, where the link parameters do not change
dynamically. By using `phylink_set_fixed_link()`, drivers can easily set up
the fixed link state during initialization or configuration changes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10G-QXGMII is a MAC-to-PHY interface defined by the USXGMII multiport
specification. It uses the same signaling as USXGMII, but it multiplexes
4 ports over the link, resulting in a maximum speed of 2.5G per port.
Some in-tree SoCs like the NXP LS1028A use "usxgmii" when they mean
either the single-port USXGMII or the quad-port 10G-QXGMII variant, and
they could get away just fine with that thus far. But there is a need to
distinguish between the 2 as far as SerDes drivers are concerned.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Of the two users of phylink_config->ovr_an_inband, both manually check
for a fixed link before setting this flag (or clearing it if they find
a fixed link.) This is unnecessary complication.
Test ovr_an_inband before checking for the fixed-link properties, which
will allow ovr_an_inband to be overriden by a fixed link specification.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/E1sCJMq-00Ecqv-P8@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Of the two users of phylink_config->ovr_an_inband, both manually check
for a fixed link before setting this flag (or clearing it if they find
a fixed link.) This is unnecessary complication.
Rearrange phylink_parse_mode() a little so we can change how
phylink_config->ovr_an_inband works. This will allow the flag to be
tested before checking for the fixed link properties in the next patch.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/E1sCJMl-00Ecqp-K0@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the phy_device as a parameter to the sfp upstream .disconnect_phy
operation. This is preparatory work to help track phy devices across
a net_device's link.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC drivers (e.g. stmmac) require a continuous receive clock signal to
be generated by a PCS that is handled by a standalone PCS driver.
Such a PCS driver does not have access to a PHY device, thus cannot check
the PHY_F_RXC_ALWAYS_ON flag. They cannot check max_requires_rxc in the
phylink config either, since it is a private member. Therefore, a new flag
is needed to signal to the PCS that it should keep the RX clock signal up
at all times.
Co-developed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-2-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some MAC controllers (e.g. stmmac) require their connected PHY to
continuously provide a receive clock signal. This can cause issues in two
cases:
1. The clock signal hasn't been started yet by the time the MAC driver
initializes its hardware. This can make the initialization fail, as in
the case of the rzn1 GMAC1 driver.
2. The clock signal is cut during a power saving event. By the time the
MAC is brought back up, the clock signal is still not active since
phylink_start hasn't been called yet. This brings us back to case 1.
If a PHY driver reads this flag, it should ensure that the receive clock
signal is started as soon as possible, and that it isn't brought down when
the PHY goes into suspend.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[rgantois: commit log]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-1-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move phylink_pcs_neg_mode() from the header file into the .c file since
nothing should be using it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the phy_device as a parameter to the sfp upstream .disconnect_phy
operation. This is preparatory work to help track phy devices across
a net_device's link.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_parse_mode() populates all possible supported link modes for a
given phy_interface_t, for the case where a phylib phy may be absent and
we can't retrieve the supported link modes from that.
Russell points out that since the introduction of the generic validation
helpers phylink_get_capabilities() and phylink_caps_to_linkmodes(), we
can rewrite this procedure to populate the pl->supported mask, so that
instead of spelling out the link modes, we derive an intermediary
mac_capabilities bit field, and we convert that to the equivalent link
modes.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs such as Aquantia, Broadcom 84881, and Marvell 88X33x0 can
switch between a set of interface types depending on the negotiated
media speed, or can use rate adaption for some or all of these
interface types.
We currently assume that these are Clause 45 PHYs that are configured
not to use a specific set of interface modes, which has worked so far,
but is just a work-around. In this workaround, we validate using all
interfaces that the MAC supports, which can lead to extra modes being
advertised that can not be supported.
To properly address this, switch to using the newly introduced PHY
possible_interfaces bitmap which indicates which interface modes will
be used by the PHY as configured. We calculate the union of the PHY's
possible interfaces and MACs supported interfaces, checking that is
non-empty. If the PHY is on a SFP, we further reduce the set by those
which can be used on a SFP module, again checking that is non-empty.
Finally, we validate the subset of interfaces, taking account of
whether rate matching will be used for each individual interface mode.
This becomes independent of whether the PHY is clause 22 or clause 45.
It is encouraged that all PHYs that switch interface modes or use
rate matching should populate phydev->possible_interfaces.
Tested-by: Luo Jie <quic_luoj@quicinc.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1r6VIV-00DDMF-Pi@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When bringing up a PHY, we need to work out which ethtool link modes it
should support and advertise. Clause 22 PHYs operate in a single
interface mode, which can be easily dealt with. However, clause 45 PHYs
tend to switch interface mode depending on the media. We need more
flexible validation at this point, so this patch splits out that code
in preparation to changing it.
Tested-by: Luo Jie <quic_luoj@quicinc.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1r6VIQ-00DDM9-LK@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers using phylink, by calling netif_carrier_off in
phylink_create.
Fixes: 089381b27a ("leds: initial support for Turris Omnia LEDs")
Cc: stable@vger.kernel.org
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a new method, mac_get_caps() to get the MAC capabilities for
the specified interface mode. This is for MACs which have special
requirements, such as not supporting half-duplex in certain interface
modes, and will replace the validate() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qsPk5-009wiX-G5@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PSGMII interface is similar to QSGMII. The main difference
is that the PSGMII interface combines five SGMII lines into a
single link while in QSGMII only four lines are combined.
Similarly to the QSGMII, this interface mode might also needs
special handling within the MAC driver.
It is commonly used by Qualcomm with their QCA807x PHY series and
modern WiSoC-s.
Add definitions for the PHY layer to allow to express this type
of connection between the MAC and PHY.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Explicitly invalidate the phylink_link_state structure members in
mac_config that do not contain reliable information for this function,
thereby preventing their future incorrect use.
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The mac_an_restart() method is now completely unused, and has been
superseded by phylink_pcs support. Remove this method.
Since phylink_pcs_mac_an_restart() now only deals with the PCS, rename
the function to remove the _mac infix.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a function, phylink_pcs_change() which can be used by PCs drivers
to notify phylink about changes to the PCS link state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
