When user enabled HDCP feature, userspace will set HDCP content
to DRM_MODE_CONTENT_PROTECTION_DESIRED. Next, anx7625 will update
HDCP content to DRM_MODE_CONTENT_PROTECTION_ENABLED if down stream
support HDCP feature.
As anx7625 bridge IC will be power down after call .atomic_disable(),
then all HDCP status will be lost on chip. So we should reestablish
HDCP again in .atomic_enable(), and update hdcp content to DESIRE if
current HDCP content is ENABLE in .atomic_disable().
v4:
- Change HDCP content value to DESIRED if HDCP status is ENABLE in bridge
interface .atomic_enable().
v3:
- Move hdcp content value checking from bridge interface
.atomic_check() to .atomic_enable()
v2:
- Add more details in commit message
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Tested-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241219070330.224996-1-xji@analogixsemi.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241219070330.224996-1-xji@analogixsemi.com
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
- In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
before/after setting ADV7511_REG_AUDIO_INFOFRAME.
- In audio_startup() use the correct register for clearing
AUDIO_UPDATE bit.
The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.
Note that this patchs replaces writing REG_GC(1) with
REG_INFOFRAME_UPDATE. Bit 5 of REG_GC(1) is positioned within field
GC_PP[3:0] and that field doesn't control audio infoframe and is read-
only. My conclusion therefore was that the author if this code meant to
clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning.
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 53c515befe ("drm/bridge: adv7511: Add Audio support")
Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119-adv7511-audio-info-frame-v4-1-4ae68e76c89c@axis.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add a optional properties to change LVDS output voltage. This should not
be static as this depends mainly on the connected display voltage
requirement. We have three properties:
- "ti,lvds-termination-ohms", which sets near end termination,
- "ti,lvds-vod-swing-data-microvolt" and
- "ti,lvds-vod-swing-clock-microvolt" which both set LVDS differential
output voltage for data and clock lanes. They are defined as an array
with min and max values. The appropriate bitfield will be set if
selected constraints can be met.
If "ti,lvds-termination-ohms" is not defined the default of 200 Ohm near
end termination will be used. Selecting only one:
"ti,lvds-vod-swing-data-microvolt" or
"ti,lvds-vod-swing-clock-microvolt" can be done, but the output voltage
constraint for only data/clock lanes will be met. Setting both is
recommended.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241216085410.1968634-3-andrej.picej@norik.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241216085410.1968634-3-andrej.picej@norik.com
The v6.13-rc2 release included a bunch of breaking changes,
specifically the MODULE_IMPORT_NS commit.
Backmerge in order to fix them before the next pull-request.
Include the fix from Stephen Roswell.
Caused by commit
25c3fd1183 ("drm/virtio: Add a helper to map and note the dma addrs and lengths")
Interacting with commit
cdd30ebb1b ("module: Convert symbol namespace to string literal")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20241209121717.2abe8026@canb.auug.org.au
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm updates from Dave Airlie:
"There's a lot of rework, the panic helper support is being added to
more drivers, v3d gets support for HW superpages, scheduler
documentation, drm client and video aperture reworks, some new
MAINTAINERS added, amdgpu has the usual lots of IP refactors, Intel
has some Pantherlake enablement and xe is getting some SRIOV bits, but
just lots of stuff everywhere.
core:
- split DSC helpers from DP helpers
- clang build fixes for drm/mm test
- drop simple pipeline support for gem vram
- document submission error signaling
- move drm_rect to drm core module from kms helper
- add default client setup to most drivers
- move to video aperture helpers instead of drm ones
tests:
- new framebuffer tests
ttm:
- remove swapped and pinned BOs from TTM lru
panic:
- fix uninit spinlock
- add ABGR2101010 support
bridge:
- add TI TDP158 support
- use standard PM OPS
dma-fence:
- use read_trylock instead of read_lock to help lockdep
scheduler:
- add errno to sched start to report different errors
- add locking to drm_sched_entity_modify_sched
- improve documentation
xe:
- add drm_line_printer
- lots of refactoring
- Enable Xe2 + PES disaggregation
- add new ARL PCI ID
- SRIOV development work
- fix exec unnecessary implicit fence
- define and parse OA sync props
- forcewake refactoring
i915:
- Enable BMG/LNL ultra joiner
- Enable 10bpx + CCS scanout on ICL+, fp16/CCS on TGL+
- use DSB for plane/color mgmt
- Arrow lake PCI IDs
- lots of i915/xe display refactoring
- enable PXP GuC autoteardown
- Pantherlake (PTL) Xe3 LPD display enablement
- Allow fastset HDR infoframe changes
- write DP source OUI for non-eDP sinks
- share PCI IDs between i915 and xe
amdgpu:
- SDMA queue reset support
- SMU 13.0.6, JPEG 4.0.3 updates
- Initial runtime repartitioning support
- rework IP structs for multiple IP instances
- Fetch EDID from _DDC if available
- SMU13 zero rpm user control
- lots of fixes/cleanups
amdkfd:
- Increase event FIFO size
- add topology cap flag for per queue reset
msm:
- DPU:
- SA8775P support
- (disabled by default) MSM8917, MSM8937, MSM8953 and MSM8996 support
- Enable large framebuffer support
- Drop MSM8998 and SDM845
- DP:
- SA8775P support
- GPU:
- a7xx preemption support
- Adreno A663 support
ast:
- warn about unsupported TX chips
ivpu:
- add coredump
- add pantherlake support
rockchip:
- 4K@60Hz display enablement
- generate pll programming tables
panthor:
- add timestamp query API
- add realtime group priority
- add fdinfo support
etnaviv:
- improve handling of DMA address limits
- improve GPU hangcheck
exynos:
- Decon Exynos7870 support
mediatek:
- add OF graph support
omap:
- locking fixes
bochs:
- convert to gem/shmem from simpledrm
v3d:
- support big/super pages
- add gemfs
vc4:
- BCM2712 support refactoring
- add YUV444 format support
udmabuf:
- folio related fixes
nouveau:
- add panic support on nv50+"
* tag 'drm-next-2024-11-21' of https://gitlab.freedesktop.org/drm/kernel: (1583 commits)
drm/xe/guc: Fix dereference before NULL check
drm/amd: Fix initialization mistake for NBIO 7.7.0
Revert "drm/amd/display: parse umc_info or vram_info based on ASIC"
drm/amd/display: Fix failure to read vram info due to static BP_RESULT
drm/amdgpu: enable GTT fallback handling for dGPUs only
drm/amd/amdgpu: limit single process inside MES
drm/fourcc: add AMD_FMT_MOD_TILE_GFX9_4K_D_X
drm/amdgpu/mes12: correct kiq unmap latency
drm/amdgpu: Support vcn and jpeg error info parsing
drm/amd : Update MES API header file for v11 & v12
drm/amd/amdkfd: add/remove kfd queues on start/stop KFD scheduling
drm/amdkfd: change kfd process kref count at creation
drm/amdgpu: Cleanup shift coding style
drm/amd/amdgpu: Increase MES log buffer to dump mes scratch data
drm/amdgpu: Implement virt req_ras_err_count
drm/amdgpu: VF Query RAS Caps from Host if supported
drm/amdgpu: Add msg handlers for SRIOV RAS Telemetry
drm/amdgpu: Update SRIOV Exchange Headers for RAS Telemetry Support
drm/amd/display: 3.2.309
drm/amd/display: Adjust VSDB parser for replay feature
...
Didn't notice drm/drm-next had the build fix for drm_bridge, so ended up
committing the same patch. Sync with drm and pretend it didn't happen?
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The IT6505 bridge chip has a active low reset line. Since it is a
"reset" and not an "enable" line, the GPIO should be asserted to
put it in reset and deasserted to bring it out of reset during
the power on sequence.
The polarity was inverted when the driver was first introduced, likely
because the device family that was targeted had an inverting level
shifter on the reset line.
The MT8186 Corsola devices already have the IT6505 in their device tree,
but the whole display pipeline is actually disabled and won't be enabled
until some remaining issues are sorted out. The other known user is
the MT8183 Kukui / Jacuzzi family; their device trees currently do not
have the IT6505 included.
Fix the polarity in the driver while there are no actual users.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029095411.657616-1-wenst@chromium.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
The Synopsys DesignWare HDMI 2.1 Quad-Pixel (QP) TX Controller IP
supports the following features, among others:
* Fixed Rate Link (FRL)
* Display Stream Compression (DSC)
* 4K@120Hz and 8K@60Hz video modes
* Variable Refresh Rate (VRR) including Quick Media Switching (QMS), aka
Cinema VRR
* Fast Vactive (FVA), aka Quick Frame Transport (QFT)
* SCDC I2C DDC access
* TMDS Scrambler enabling 2160p@60Hz with RGB/YCbCr4:4:4
* YCbCr4:2:0 enabling 2160p@60Hz at lower HDMI link speeds
* Multi-stream audio
* Enhanced Audio Return Channel (EARC)
Add library containing common helpers to enable basic support, i.e. RGB
output up to 4K@30Hz, without audio, CEC or any HDMI 2.1 specific
features.
Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241016-b4-rk3588-bridge-upstream-v10-1-87ef92a6d14e@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
When a display controller driver uses DRM_BRIDGE_ATTACH_NO_CONNECTOR,
tc358767 will behave properly and skip the creation of the connector.
However, tc_get_display_props(), which is used to find out about the DP
monitor and link, is only called from two places: .atomic_enable() and
tc_connector_get_modes(). The latter is only used when tc358767 creates
its own connector, i.e. when DRM_BRIDGE_ATTACH_NO_CONNECTOR is _not_
set.
Thus, the driver never finds out the link properties before get_edid()
is called. With num_lanes of 0 and link_rate of 0 there are not many
valid modes...
Fix this by adding tc_get_display_props() call at the beginning of
get_edid(), so that we have up to date information before looking at the
modes.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Closes: https://lore.kernel.org/all/24282420-b4dd-45b3-bb1c-fc37fe4a8205@siemens.com/
Fixes: de5e6c027a ("drm/bridge: tc358767: add drm_panel_bridge support")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231108-tc358767-v2-2-25c5f70a2159@ideasonboard.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
drm-misc-next for v6.13:
UAPI Changes:
- Add drm fdinfo support to panthor, and add sysfs knob to toggle.
Cross-subsystem Changes:
- Convert fbdev drivers to use backlight power constants.
- Some small dma-fence fixes.
- Some kernel-doc fixes.
Core Changes:
- Small drm client fixes.
- Document requirements that you need to file a bug before marking a test as flaky.
- Remove swapped and pinned bo's from TTM lru list.
Driver Changes:
- Assorted small fixes to panel/elida-kd35t133, nouveau, vc4, imx.
- Fix some bridges to drop cached edids on power off.
- Add Jenson BL-JT60050-01A, Samsung s6e3ha8 & AMS639RQ08 panels.
- Make 180° rotation work on ilitek-ili9881c, even for already-rotated
panels.
-
Signed-off-by: Dave Airlie <airlied@redhat.com>
# Conflicts:
# drivers/gpu/drm/panthor/panthor_drv.c
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8dc111ca-d20c-4e0d-856e-c12d208cbf2a@linux.intel.com
drm-misc-next for v6.12:
UAPI Changes:
- Add panthor/DEV_QUERY_TIMESTAMP_INFO query.
Cross-subsystem Changes:
- Updated dt bindings.
- Add documentation explaining default errnos for fences.
- Mark dma-buf heaps creation functions as __init.
Core Changes:
- Split DSC helpers from DP helpers.
- Clang build fixes for drm/mm test.
- Remove simple pipeline support for gem-vram,
no longer any users left after converting bochs.
- Add erno to drm_sched_start to distinguish between GPU and queue
reset.
- Add drm_framebuffer testcases.
- Fix uninitialized spinlock acquisition with CONFIG_DRM_PANIC=n.
- Use read_trylock instead of read_lock in dma_fence_begin_signalling to
quiesce lockdep.
Driver Changes:
- Assorted small fixes and updates for tegra, host1x, imagination,
nouveau, panfrost, panthor, panel/ili9341, mali, exynos,
panel/samsung-s6e3fa7, ast, bridge/ti-sn65dsi86, panel/himax-hx83112a,
bridge/tc358767, bridge/imx8mp-hdmi-tx, panel/khadas-ts050,
panel/nt36523, panel/sony-acx565akm, kmb, accel/qaic, omap, v3d.
- Add bridge/TI TDP158.
- Assorted documentation updates.
- Convert bochs from simple drm to gem shmem, and check modes
against available memory.
- Many VC4 fixes, most related to scaling and YUV support.
- Convert some drivers to use SYSTEM_SLEEP_PM_OPS and RUNTIME_PM_OPS.
- Rockchip 4k@60 support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/445713a6-2427-4c53-8ec2-3a894ec62405@linux.intel.com
The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 11feaef69d ("drm/bridge: it6505: Add caching for EDID")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-3-treapking@chromium.org
The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 8bdfc5dae4 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-2-treapking@chromium.org
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
