The GCC plugin feature leads to different kernel configurations on what
ought to be equivalent build systems because they depend on the build
hosts native compilers rather than the cross compilers needed for the
target. This causes problems with module symbol version mismatches.
Disable GCC plugins for all build hosts.
Advanced build script hackery borrowed from a patch by milhouse.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[ Upstream commit f2f02ebd8f ]
When cc-option and friends evaluate compiler flags, the temporary file
$$TMP is created as an output object, and automatically cleaned up.
The actual file path of $$TMP is .<pid>.tmp, here <pid> is the process
ID of $(shell ...) invoked from cc-option. (Please note $$$$ is the
escape sequence of $$).
Such garbage files are cleaned up in most cases, but some compiler flags
create additional output files.
For example, -gsplit-dwarf creates a .dwo file.
When CONFIG_DEBUG_INFO_SPLIT=y, you will see a bunch of .<pid>.dwo files
left in the top of build directories. You may not notice them unless you
do 'ls -a', but the garbage files will increase every time you run 'make'.
This commit changes the temporary object path to .tmp_<pid>/tmp, and
removes .tmp_<pid> directory when exiting. Separate build artifacts such
as *.dwo will be cleaned up all together because their file paths are
usually determined based on the base name of the object.
Another example is -ftest-coverage, which outputs the coverage data into
<base-name-of-object>.gcno
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5967577231 ]
Misuse of CONFIG_* in UAPI headers should result in an error. These config
options can be set in userspace by the user application which includes
these headers to control the APIs and structures being used in a kernel
which supports multiple targets.
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72d24accf0 ]
When System.map was generated, the kernel used mksysmap to
filter the kernel symbols, but all the symbols with the
second letter 'L' in the kernel were filtered out, not just
the symbols starting with 'dot + L'.
For example:
ashimida@ubuntu:~/linux$ cat System.map |grep ' .L'
ashimida@ubuntu:~/linux$ nm -n vmlinux |grep ' .L'
ffff0000088028e0 t bLength_show
......
ffff0000092e0408 b PLLP_OUTC_lock
ffff0000092e0410 b PLLP_OUTA_lock
The original intent should be to filter out all local symbols
starting with '.L', so the dot should be escaped.
Fixes: 00902e9847 ("mksysmap: Add h8300 local symbol pattern")
Signed-off-by: ashimida <ashimida@linux.alibaba.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 90ceddcb49 upstream.
Simplify gen_btf logic to make it work with llvm-objcopy. The existing
'file format' and 'architecture' parsing logic is brittle and does not
work with llvm-objcopy/llvm-objdump.
'file format' output of llvm-objdump>=11 will match GNU objdump, but
'architecture' (bfdarch) may not.
.BTF in .tmp_vmlinux.btf is non-SHF_ALLOC. Add the SHF_ALLOC flag
because it is part of vmlinux image used for introspection. C code
can reference the section via linker script defined __start_BTF and
__stop_BTF. This fixes a small problem that previous .BTF had the
SHF_WRITE flag (objcopy -I binary -O elf* synthesized .data).
Additionally, `objcopy -I binary` synthesized symbols
_binary__btf_vmlinux_bin_start and _binary__btf_vmlinux_bin_stop (not
used elsewhere) are replaced with more commonplace __start_BTF and
__stop_BTF.
Add 2>/dev/null because GNU objcopy (but not llvm-objcopy) warns
"empty loadable segment detected at vaddr=0xffffffff81000000, is this intentional?"
We use a dd command to change the e_type field in the ELF header from
ET_EXEC to ET_REL so that lld will accept .btf.vmlinux.bin.o. Accepting
ET_EXEC as an input file is an extremely rare GNU ld feature that lld
does not intend to support, because this is error-prone.
The output section description .BTF in include/asm-generic/vmlinux.lds.h
avoids potential subtle orphan section placement issues and suppresses
--orphan-handling=warn warnings.
Fixes: df786c9b94 ("bpf: Force .BTF section start to zero when dumping from vmlinux")
Fixes: cb0cc635c7 ("powerpc: Include .BTF section")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Stanislav Fomichev <sdf@google.com>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Link: https://github.com/ClangBuiltLinux/linux/issues/871
Link: https://lore.kernel.org/bpf/20200318222746.173648-1-maskray@google.com
Signed-off-by: Maria Teguiani <teguiani@google.com>
Tested-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af73d78bd3 ]
When CONFIG_DEBUG_INFO is enabled, the two kallsyms linking steps spend
time collecting and writing the dwarf sections to the temporary output
files. kallsyms does not need this information, and leaving it off
halves their linking time. This is especially noticeable without
CONFIG_DEBUG_INFO_REDUCED. The BTF linking stage, however, does still
need those details.
Refactor the BTF and kallsyms generation stages slightly for more
regularized temporary names. Skip debug during kallsyms links.
Additionally move "info BTF" to the correct place since commit
8959e39272 ("kbuild: Parameterize kallsyms generation and correct
reporting"), which added "info LD ..." to vmlinux_link calls.
For a full debug info build with BTF, my link time goes from 1m06s to
0m54s, saving about 12 seconds, or 18%.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/202003031814.4AEA3351@keescook
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7527373fe ]
Remove "params.h" include, which has been dropped in GCC 10.
Remove is_a_helper() macro, which is now defined in gimple.h, as seen
when running './scripts/gcc-plugin.sh g++ g++ gcc':
In file included from <stdin>:1:
./gcc-plugins/gcc-common.h:852:13: error: redefinition of ‘static bool is_a_helper<T>::test(U*) [with U = const gimple; T = const ggoto*]’
852 | inline bool is_a_helper<const ggoto *>::test(const_gimple gs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from ./gcc-plugins/gcc-common.h:125,
from <stdin>:1:
/usr/lib/gcc/x86_64-redhat-linux/10/plugin/include/gimple.h:1037:1: note: ‘static bool is_a_helper<T>::test(U*) [with U = const gimple; T = const ggoto*]’ previously declared here
1037 | is_a_helper <const ggoto *>::test (const gimple *gs)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Add -Wno-format-diag to scripts/gcc-plugins/Makefile to avoid
meaningless warnings from error() formats used by plugins:
scripts/gcc-plugins/structleak_plugin.c: In function ‘int plugin_init(plugin_name_args*, plugin_gcc_version*)’:
scripts/gcc-plugins/structleak_plugin.c:253:12: warning: unquoted sequence of 2 consecutive punctuation characters ‘'-’ in format [-Wformat-diag]
253 | error(G_("unknown option '-fplugin-arg-%s-%s'"), plugin_name, argv[i].key);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Frédéric Pierret (fepitre) <frederic.pierret@qubes-os.org>
Link: https://lore.kernel.org/r/20200407113259.270172-1-frederic.pierret@qubes-os.org
[kees: include -Wno-format-diag for plugin builds]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e08df079b2 upstream.
If the trapping instruction contains a ':', for a memory access through
segment registers for example, the sed substitution will insert the '*'
marker in the middle of the instruction instead of the line address:
2b: 65 48 0f c7 0f cmpxchg16b %gs:*(%rdi) <-- trapping instruction
I started to think I had forgotten some quirk of the assembly syntax
before noticing that it was actually coming from the script. Fix it to
add the address marker at the right place for these instructions:
28: 49 8b 06 mov (%r14),%rax
2b:* 65 48 0f c7 0f cmpxchg16b %gs:(%rdi) <-- trapping instruction
30: 0f 94 c0 sete %al
Fixes: 18ff44b189 ("scripts/decodecode: make faulting insn ptr more robust")
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20200419223653.GA31248@visor
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e461bc9f9a ]
Sed broke on some strings as it used colon as a separator.
I made it more robust by using \001, which is legit POSIX AFAIK.
E.g. ./config --set-str CONFIG_USBNET_DEVADDR "de:ad:be:ef:00:01"
failed with: sed: -e expression #1, char 55: unknown option to `s'
Signed-off-by: Jeremie Francois (on alpha) <jeremie.francois@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3d4b223868 upstream.
Since commit 7a04960560 ("kbuild: fix DT binding schema rule to detect
command line changes"), this rule is every time re-run even if you change
nothing.
cmd_dtc takes one additional parameter to pass to the -O option of dtc.
We need to pass 'yaml' to if_changed_rule. Otherwise, cmd-check invoked
from if_changed_rule is false positive.
Fixes: 7a04960560 ("kbuild: fix DT binding schema rule to detect command line changes")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8cc4fd7350 ]
When a compiler supports multiple architectures, some compiler features
can be dependent on the target architecture.
This is typical for Clang, which supports multiple LLVM backends.
Even for GCC, we need to take care of biarch compiler cases.
It is not a problem when we evaluate cc-option in Makefiles because
cc-option is tested against the flag in question + $(KBUILD_CFLAGS).
The cc-option in Kconfig, on the other hand, does not accumulate
tested flags. Due to this simplification, it could potentially test
cc-option against a different target.
At first, Kconfig always evaluated cc-option against the host
architecture.
Since commit e8de12fb7c ("kbuild: Check for unknown options with
cc-option usage in Kconfig and clang"), in case of cross-compiling
with Clang, the target triple is correctly passed to Kconfig.
The case with biarch GCC (and native build with Clang) is still not
handled properly. We need to pass some flags to specify the target
machine bit.
Due to the design, all the macros in Kconfig are expanded in the
parse stage, where we do not know the target bit size yet.
For example, arch/x86/Kconfig allows a user to toggle CONFIG_64BIT.
If a compiler flag -foo depends on the machine bit, it must be tested
twice, one with -m32 and the other with -m64.
However, -m32/-m64 are not always recognized. So, this commits adds
m64-flag and m32-flag macros. They expand to -m32, -m64, respectively
if supported. Or, they expand to an empty string if unsupported.
The typical usage is like this:
config FOO
bool
default $(cc-option,$(m64-flag) -foo) if 64BIT
default $(cc-option,$(m32-flag) -foo)
This is clumsy, but there is no elegant way to handle this in the
current static macro expansion.
There was discussion for static functions vs dynamic functions.
The consensus was to go as far as possible with the static functions.
(https://lkml.org/lkml/2018/3/2/22)
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: George Spelvin <lkml@sdf.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e33a814e77 upstream.
gcc 10 will default to -fno-common, which causes this error at link
time:
(.text+0x0): multiple definition of `yylloc'; dtc-lexer.lex.o (symbol from plugin):(.text+0x0): first defined here
This is because both dtc-lexer as well as dtc-parser define the same
global symbol yyloc. Before with -fcommon those were merged into one
defintion. The proper solution would be to to mark this as "extern",
however that leads to:
dtc-lexer.l:26:16: error: redundant redeclaration of 'yylloc' [-Werror=redundant-decls]
26 | extern YYLTYPE yylloc;
| ^~~~~~
In file included from dtc-lexer.l:24:
dtc-parser.tab.h:127:16: note: previous declaration of 'yylloc' was here
127 | extern YYLTYPE yylloc;
| ^~~~~~
cc1: all warnings being treated as errors
which means the declaration is completely redundant and can just be
dropped.
Signed-off-by: Dirk Mueller <dmueller@suse.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[robh: cherry-pick from upstream]
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5190044c29 upstream.
In order to preserve backwards compatability with kmod tools, we have to
move the namespace field in Module.symvers last, as the depmod -e -E
option looks at the first three fields in Module.symvers to check symbol
versions (and it's expected they stay in the original order of crc,
symbol, module).
In addition, update an ancient comment above read_dump() in modpost that
suggested that the export type field in Module.symvers was optional. I
suspect that there were historical reasons behind that comment that are
no longer accurate. We have been unconditionally printing the export
type since 2.6.18 (commit bd5cbcedf4), which is over a decade ago now.
Fix up read_dump() to treat each field as non-optional. I suspect the
original read_dump() code treated the export field as optional in order
to support pre <= 2.6.18 Module.symvers (which did not have the export
type field). Note that although symbol namespaces are optional, the
field will not be omitted from Module.symvers if a symbol does not have
a namespace. In this case, the field will simply be empty and the next
delimiter or end of line will follow.
Cc: stable@vger.kernel.org
Fixes: cb9b55d21f ("modpost: add support for symbol namespaces")
Tested-by: Matthias Maennich <maennich@google.com>
Reviewed-by: Matthias Maennich <maennich@google.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ecaf069da upstream.
Currently, some sanity checks for uapi headers are done by
scripts/headers_check.pl, which is wired up to the 'headers_check'
target in the top Makefile.
It is true compiling headers has better test coverage, but there
are still several headers excluded from the compile test. I like
to keep headers_check.pl for a while, but we can delete a lot of
code by moving the build rule to usr/include/Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcbb8461fd upstream.
There are both positive and negative options about this feature.
At first, I thought it was a good idea, but actually Linus stated a
negative opinion (https://lkml.org/lkml/2019/9/29/227). I admit it
is ugly and annoying.
The baseline I'd like to keep is the compile-test of uapi headers.
(Otherwise, kernel developers have no way to ensure the correctness
of the exported headers.)
I will maintain a small build rule in usr/include/Makefile.
Remove the other header test functionality.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[ added to 5.4.y due to start of build warnings from backported patches
because of this feature - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a04960560 upstream.
This if_change_rule is not working properly; it cannot detect any
command line change.
The reason is because cmd-check in scripts/Kbuild.include compares
$(cmd_$@) and $(cmd_$1), but cmd_dtc_dt_yaml does not exist here.
For if_change_rule to work properly, the stem part of cmd_* and rule_*
must match. Because this cmd_and_fixdep invokes cmd_dtc, this rule must
be named rule_dtc.
Fixes: 4f0e3a57d6 ("kbuild: Add support for DT binding schema checks")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a67a6ccb0 ]
When trying to compile with CONFIG_DEBUG_INFO_BTF enabled, I got this
error:
% make -s
Failed to generate BTF for vmlinux
Try to disable CONFIG_DEBUG_INFO_BTF
make[3]: *** [vmlinux] Error 1
Compiling again without -s shows the true error (that pahole is
missing), but since this is fatal, we should show the error
unconditionally on stderr as well, not silence it using the `info`
function. With this patch:
% make -s
BTF: .tmp_vmlinux.btf: pahole (pahole) is not available
Failed to generate BTF for vmlinux
Try to disable CONFIG_DEBUG_INFO_BTF
make[3]: *** [vmlinux] Error 1
Signed-off-by: Chris Down <chris@chrisdown.name>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200122000110.GA310073@chrisdown.name
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bed1b7b9d ]
Currently, -E (stop after the preprocessing stage) is used to check
whether the given compiler flag is supported.
While it is faster than -S (or -c), it can be false-positive. You need
to run the compilation proper to check the flag more precisely.
For example, -E and -S disagree about the support of
"--param asan-instrument-allocas=1".
$ gcc -Werror --param asan-instrument-allocas=1 -E -x c /dev/null -o /dev/null
$ echo $?
0
$ gcc -Werror --param asan-instrument-allocas=1 -S -x c /dev/null -o /dev/null
cc1: error: invalid --param name ‘asan-instrument-allocas’; did you mean ‘asan-instrument-writes’?
$ echo $?
1
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88fe89a471 ]
Bartosz Golaszewski reports that when "make {menu,n,g,x}config" fails
due to missing packages, a temporary file is left over, which is not
ignored by git.
For example, if GTK+ is not installed:
$ make gconfig
*
* Unable to find the GTK+ installation. Please make sure that
* the GTK+ 2.0 development package is correctly installed.
* You need gtk+-2.0 gmodule-2.0 libglade-2.0
*
scripts/kconfig/Makefile:208: recipe for target 'scripts/kconfig/gconf-cfg' failed
make[1]: *** [scripts/kconfig/gconf-cfg] Error 1
Makefile:567: recipe for target 'gconfig' failed
make: *** [gconfig] Error 2
$ git status
HEAD detached at v5.4
Untracked files:
(use "git add <file>..." to include in what will be committed)
scripts/kconfig/gconf-cfg.tmp
nothing added to commit but untracked files present (use "git add" to track)
This is because the check scripts are run with filechk, which misses
to clean up the temporary file on failure.
When the line
{ $(filechk_$(1)); } > $@.tmp;
... fails, it exits immediately due to the 'set -e'. Use trap to make
sure to delete the temporary file on exit.
For extra safety, I replaced $@.tmp with $(dot-target).tmp to make it
a hidden file.
Reported-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8fb7d7e48 ]
Running randconfig on arm64 using KCONFIG_SEED=0x40C5E904 (e.g. on v5.5)
produces the .config with CONFIG_EFI=y and CONFIG_CPU_BIG_ENDIAN=y,
which does not meet the !CONFIG_CPU_BIG_ENDIAN dependency.
This is because the user choice for CONFIG_CPU_LITTLE_ENDIAN vs
CONFIG_CPU_BIG_ENDIAN is set by randomize_choice_values() after the
value of CONFIG_EFI is calculated.
When this happens, the has_changed flag should be set.
Currently, it takes the result from the last iteration. It should
accumulate all the results of the loop.
Fixes: 3b9a19e089 ("kconfig: loop as long as we changed some symbols in randconfig")
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1630146db2 upstream.
scripts/find-unused-docs.sh invokes scripts/kernel-doc to find out if a
source file contains kerneldoc or not.
However, as it passes the no longer supported "-text" option to
scripts/kernel-doc, the latter prints out its help text, causing all
files to be considered containing kerneldoc.
Get rid of these false positives by removing the no longer supported
"-text" option from the scripts/kernel-doc invocation.
Cc: stable@vger.kernel.org # 4.16+
Fixes: b051426753 ("scripts: kernel-doc: get rid of unused output formats")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200127093107.26401-1-geert+renesas@glider.be
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 927d780ee3 upstream.
Scenario 1, ARMv7
=================
If code in arch/arm/kernel/ftrace.c would operate on mcount() pointer
the following may be generated:
00000230 <prealloc_fixed_plts>:
230: b5f8 push {r3, r4, r5, r6, r7, lr}
232: b500 push {lr}
234: f7ff fffe bl 0 <__gnu_mcount_nc>
234: R_ARM_THM_CALL __gnu_mcount_nc
238: f240 0600 movw r6, #0
238: R_ARM_THM_MOVW_ABS_NC __gnu_mcount_nc
23c: f8d0 1180 ldr.w r1, [r0, #384] ; 0x180
FTRACE currently is not able to deal with it:
WARNING: CPU: 0 PID: 0 at .../kernel/trace/ftrace.c:1979 ftrace_bug+0x1ad/0x230()
...
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.116-... #1
...
[<c0314e3d>] (unwind_backtrace) from [<c03115e9>] (show_stack+0x11/0x14)
[<c03115e9>] (show_stack) from [<c051a7f1>] (dump_stack+0x81/0xa8)
[<c051a7f1>] (dump_stack) from [<c0321c5d>] (warn_slowpath_common+0x69/0x90)
[<c0321c5d>] (warn_slowpath_common) from [<c0321cf3>] (warn_slowpath_null+0x17/0x1c)
[<c0321cf3>] (warn_slowpath_null) from [<c038ee9d>] (ftrace_bug+0x1ad/0x230)
[<c038ee9d>] (ftrace_bug) from [<c038f1f9>] (ftrace_process_locs+0x27d/0x444)
[<c038f1f9>] (ftrace_process_locs) from [<c08915bd>] (ftrace_init+0x91/0xe8)
[<c08915bd>] (ftrace_init) from [<c0885a67>] (start_kernel+0x34b/0x358)
[<c0885a67>] (start_kernel) from [<00308095>] (0x308095)
---[ end trace cb88537fdc8fa200 ]---
ftrace failed to modify [<c031266c>] prealloc_fixed_plts+0x8/0x60
actual: 44:f2:e1:36
ftrace record flags: 0
(0) expected tramp: c03143e9
Scenario 2, ARMv4T
==================
ftrace: allocating 14435 entries in 43 pages
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/trace/ftrace.c:2029 ftrace_bug+0x204/0x310
CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.5 #1
Hardware name: Cirrus Logic EDB9302 Evaluation Board
[<c0010a24>] (unwind_backtrace) from [<c000ecb0>] (show_stack+0x20/0x2c)
[<c000ecb0>] (show_stack) from [<c03c72e8>] (dump_stack+0x20/0x30)
[<c03c72e8>] (dump_stack) from [<c0021c18>] (__warn+0xdc/0x104)
[<c0021c18>] (__warn) from [<c0021d7c>] (warn_slowpath_null+0x4c/0x5c)
[<c0021d7c>] (warn_slowpath_null) from [<c0095360>] (ftrace_bug+0x204/0x310)
[<c0095360>] (ftrace_bug) from [<c04dabac>] (ftrace_init+0x3b4/0x4d4)
[<c04dabac>] (ftrace_init) from [<c04cef4c>] (start_kernel+0x20c/0x410)
[<c04cef4c>] (start_kernel) from [<00000000>] ( (null))
---[ end trace 0506a2f5dae6b341 ]---
ftrace failed to modify
[<c000c350>] perf_trace_sys_exit+0x5c/0xe8
actual: 1e:ff:2f:e1
Initializing ftrace call sites
ftrace record flags: 0
(0)
expected tramp: c000fb24
The analysis for this problem has been already performed previously,
refer to the link below.
Fix the above problems by allowing only selected reloc types in
__mcount_loc. The list itself comes from the legacy recordmcount.pl
script.
Link: https://lore.kernel.org/lkml/56961010.6000806@pengutronix.de/
Cc: stable@vger.kernel.org
Fixes: ed60453fa8 ("ARM: 6511/1: ftrace: add ARM support for C version of recordmcount")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df786c9b94 upstream.
While trying to figure out why fentry_fexit selftest doesn't pass for me
(old pahole, broken BTF), I found out that my latest patch can break vmlinux
.BTF generation. objcopy preserves section start when doing --only-section,
so there is a chance (depending on where pahole inserts .BTF section) to
have leading empty zeroes. Let's explicitly force section offset to zero.
Before:
$ objcopy --set-section-flags .BTF=alloc -O binary \
--only-section=.BTF vmlinux .btf.vmlinux.bin
$ xxd .btf.vmlinux.bin | head -n1
00000000: 0000 0000 0000 0000 0000 0000 0000 0000 ................
After:
$ objcopy --change-section-address .BTF=0 \
--set-section-flags .BTF=alloc -O binary \
--only-section=.BTF vmlinux .btf.vmlinux.bin
$ xxd .btf.vmlinux.bin | head -n1
00000000: 9feb 0100 1800 0000 0000 0000 80e1 1c00 ................
^BTF magic
As part of this change, I'm also dropping '2>/dev/null' from objcopy
invocation to be able to catch possible other issues (objcopy doesn't
produce any warnings for me anymore, it did before with --dump-section).
Fixes: da5fb18225 ("bpf: Support pre-2.25-binutils objcopy for vmlinux BTF")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Cc: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191127225759.39923-1-sdf@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ffdc54b6f ]
Cross compiling the x86 kernel on a non-x86 build machine produces
the following error when CONFIG_UNWINDER_ORC is enabled, regardless
of whether libelf-dev is installed or not.
dpkg-checkbuilddeps: error: Unmet build dependencies: libelf-dev
dpkg-buildpackage: warning: build dependencies/conflicts unsatisfied; aborting
dpkg-buildpackage: warning: (Use -d flag to override.)
Since this is a build time dependency for a build tool, we need to
depend on the native version of libelf-dev so add the appropriate
annotation.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit da5fb18225 upstream.
If vmlinux BTF generation fails, but CONFIG_DEBUG_INFO_BTF is set,
.BTF section of vmlinux is empty and kernel will prohibit
BPF loading and return "in-kernel BTF is malformed".
--dump-section argument to binutils' objcopy was added in version 2.25.
When using pre-2.25 binutils, BTF generation silently fails. Convert
to --only-section which is present on pre-2.25 binutils.
Documentation/process/changes.rst states that binutils 2.21+
is supported, not sure those standards apply to BPF subsystem.
v2:
* exit and print an error if gen_btf fails (John Fastabend)
v3:
* resend with Andrii's Acked-by/Tested-by tags
Fixes: 341dfcf8d7 ("btf: expose BTF info through sysfs")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20191127161410.57327-1-sdf@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 272a721030 ]
NULL expressions are taken to always be true, as implemented by the
expr_is_yes() macro and by several other functions in expr.c. As such,
they ought to be valid inputs to expr_eq(), which compares two
expressions.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a5b0dc5a46 upstream.
I noticed that randconfig builds with gcc no longer produce a lot of
ccache hits, unlike with clang, and traced this back to plugins
now being enabled unconditionally if they are supported.
I am now working around this by adding
export CCACHE_COMPILERCHECK=/usr/bin/size -A %compiler%
to my top-level Makefile. This changes the heuristic that ccache uses
to determine whether the plugins are the same after a 'make clean'.
However, it also seems that being able to just turn off the plugins is
generally useful, at least for build testing it adds noticeable overhead
but does not find a lot of bugs additional bugs, and may be easier for
ccache users than my workaround.
Fixes: 9f671e5815 ("security: Create "kernel hardening" config area")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20191211133951.401933-1-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21915eca08 ]
build_initial_tok_table() overwrites unused sym_entry to shrink the
table size. Before the entry is overwritten, table[i].sym must be freed
since it is malloc'ed data.
This fixes the 'definitely lost' report from valgrind. I ran valgrind
against x86_64_defconfig of v5.4-rc8 kernel, and here is the summary:
[Before the fix]
LEAK SUMMARY:
definitely lost: 53,184 bytes in 2,874 blocks
[After the fix]
LEAK SUMMARY:
definitely lost: 0 bytes in 0 blocks
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 067c650c45 ]
Using Makefile's wildcard with absolute path to detect
the presence of libyaml results in false-positive
detection when cross-compiling e.g. in yocto environment.
The latter results in build error:
| scripts/dtc/yamltree.o: In function `yaml_propval_int':
| yamltree.c: undefined reference to `yaml_sequence_start_event_initialize'
| yamltree.c: undefined reference to `yaml_emitter_emit'
| yamltree.c: undefined reference to `yaml_scalar_event_initialize'
...
Use pkg-config to locate libyaml to address this scenario.
Signed-off-by: Pavel Modilaynen <pavel.modilaynen@axis.com>
[robh: silence stderr]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull arm64 fix from Will Deacon:
"One trivial fix for -rc8/final that ensures that the script used to
detect RELR relocation support in the toolchain works correctly when
$CC contains quotes. Although it fails safely (by failing to detect
the support when it exists), it would be nice to have this fixed in
5.4 given that it was only introduced in the last merge window.
Summary:
- Handle CC variables containing quotes in tools-support-relr.sh
script"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
scripts/tools-support-relr.sh: un-quote variables
When the CC variable contains quotes, e.g. when using
ccache (make CC="ccache <compiler>"), this script always
fails, so CONFIG_RELR is never enabled, even when the
toolchain supports this feature. Removing the /dev/null
redirect and invoking the script manually shows the issue:
$ CC='/usr/bin/ccache clang' ./scripts/tools-support-relr.sh
./scripts/tools-support-relr.sh: 7: ./scripts/tools-support-relr.sh: /usr/bin/ccache clang: not found
Fix this by un-quoting the variables.
Before:
$ make ARCH=arm64 CC='/usr/bin/ccache clang' LD=ld.lld \
NM=llvm-nm OBJCOPY=llvm-objcopy defconfig
$ grep RELR .config
CONFIG_ARCH_HAS_RELR=y
With this change:
$ make ARCH=arm64 CC='/usr/bin/ccache clang' LD=ld.lld \
NM=llvm-nm OBJCOPY=llvm-objcopy defconfig
$ grep RELR .config
CONFIG_TOOLS_SUPPORT_RELR=y
CONFIG_ARCH_HAS_RELR=y
CONFIG_RELR=y
Fixes: 5cf896fb6b ("arm64: Add support for relocating the kernel with RELR relocations")
Reported-by: Dmitry Golovin <dima@golovin.in>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/769
Cc: Peter Collingbourne <pcc@google.com>
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>
Pull modules fix from Jessica Yu:
"Fix `make nsdeps` for modules composed of multiple source files.
Since $mod_source_files was not in quotes in the call to
generate_deps_for_ns(), not all the source files for a module were
being passed to spatch"
* tag 'modules-for-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
scripts/nsdeps: make sure to pass all module source files to spatch
gcc's -freorder-blocks-and-partition option makes it group frequently
and infrequently used code in .text.hot and .text.unlikely sections
respectively. At least when building modules on s390, this option is
used by default.
gdb assumes that all code is located in .text section, and that .text
section is located at module load address. With such modules this is no
longer the case: there is code in .text.hot and .text.unlikely, and
either of them might precede .text.
Fix by explicitly telling gdb the addresses of code sections.
It might be tempting to do this for all sections, not only the ones in
the white list. Unfortunately, gdb appears to have an issue, when
telling it about e.g. loadable .note.gnu.build-id section causes it to
think that non-loadable .note.Linux section is loaded at address 0,
which in turn causes NULL pointers to be resolved to bogus symbols. So
keep using the white list approach for the time being.
Link: http://lkml.kernel.org/r/20191028152734.13065-1-iii@linux.ibm.com
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The nsdeps script passes a list of the module source files to
generate_deps_for_ns() as a space delimited string named $mod_source_files,
which then passes it to spatch. But since $mod_source_files is not encased
in quotes, each source file in that string is treated as a separate shell
function argument (as $2, $3, $4, etc.). However, the spatch invocation
only refers to $2, so only the first file out of $mod_source_files is
processed by spatch.
This causes problems (namely, the MODULE_IMPORT_NS() statement doesn't
get inserted) when a module is composed of many source files and the
"main" module file containing the MODULE_LICENSE() statement is not the
first file listed in $mod_source_files. Fix this by encasing
$mod_source_files in quotes so that the entirety of the string is
treated as a single argument and can be referred to as $2.
In addition, put quotes in the variable assignment of mod_source_files
to prevent any shell interpretation and field splitting.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Pull modules fixes from Jessica Yu:
- Revert __ksymtab_$namespace.$symbol naming scheme back to
__ksymtab_$symbol, as it was causing issues with depmod.
Instead, have modpost extract a symbol's namespace from __kstrtabns
and __ksymtab_strings.
- Fix `make nsdeps` for out of tree kernel builds (make O=...) caused
by unescaped '/'.
Use a different sed delimiter to avoid this problem.
* tag 'modules-for-v5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
scripts/nsdeps: use alternative sed delimiter
symbol namespaces: revert to previous __ksymtab name scheme
modpost: make updating the symbol namespace explicit
modpost: delegate updating namespaces to separate function
When doing an out of tree build with O=, the nsdeps script constructs
the absolute pathname of the module source file so that it can insert
MODULE_IMPORT_NS statements in the right place. However, ${srctree}
contains an unescaped path to the source tree, which, when used in a sed
substitution, makes sed complain:
++ sed 's/[^ ]* *//home/jeyu/jeyu-linux\/&/g'
sed: -e expression #1, char 12: unknown option to `s'
The sed substitution command 's' ends prematurely with the forward
slashes in the pathname, and sed errors out when it encounters the 'h',
which is an invalid sed substitution option. To avoid escaping forward
slashes ${srctree}, we can use '|' as an alternative delimiter for
sed instead to avoid this error.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Maennich <maennich@google.com>
Tested-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Pull more Kbuild fixes from Masahiro Yamada:
- fix a bashism of setlocalversion
- do not use the too new --sort option of tar
* tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kheaders: substituting --sort in archive creation
scripts: setlocalversion: fix a bashism
kbuild: update comment about KBUILD_ALLDIRS
Currently lx-symbols assumes that module text is always located at
module->core_layout->base, but s390 uses the following layout:
+------+ <- module->core_layout->base
| GOT |
+------+ <- module->core_layout->base + module->arch->plt_offset
| PLT |
+------+ <- module->core_layout->base + module->arch->plt_offset +
| TEXT | module->arch->plt_size
+------+
Therefore, when trying to debug modules on s390, all the symbol
addresses are skewed by plt_offset + plt_size.
Fix by adding plt_offset + plt_size to module_addr in
load_module_symbols().
Link: http://lkml.kernel.org/r/20191017085917.81791-1-iii@linux.ibm.com
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_PRINTK_CALLER is set, struct printk_log contains an
additional member caller_id. This affects the offset of the log text.
Account for this by using the type information from gdb to determine all
the offsets instead of using hardcoded values.
This fixes following error:
(gdb) lx-dmesg
Python Exception <class 'ValueError'> embedded null character:
Error occurred in Python command: embedded null character
The read_u* utility functions now take an offset argument to make them
easier to use.
Link: http://lkml.kernel.org/r/20191011142500.2339-1-joel.colledge@linbit.com
Signed-off-by: Joel Colledge <joel.colledge@linbit.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The introduction of Symbol Namespaces changed the naming schema of the
__ksymtab entries from __kysmtab__symbol to __ksymtab_NAMESPACE.symbol.
That caused some breakages in tools that depend on the name layout in
either the binaries(vmlinux,*.ko) or in System.map. E.g. kmod's depmod
would not be able to read System.map without a patch to support symbol
namespaces. A warning reported by depmod for namespaced symbols would
look like
depmod: WARNING: [...]/uas.ko needs unknown symbol usb_stor_adjust_quirks
In order to address this issue, revert to the original naming scheme and
rather read the __kstrtabns_<symbol> entries and their corresponding
values from __ksymtab_strings to update the namespace values for
symbols. After having read all symbols and handled them in
handle_modversions(), the symbols are created. In a second pass, read
the __kstrtabns_ entries and update the namespaces accordingly.
Fixes: 8651ec01da ("module: add support for symbol namespaces.")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Setting the symbol namespace of a symbol within sym_add_exported feels
displaced and lead to issues in the current implementation of symbol
namespaces. This patch makes updating the namespace an explicit call to
decouple it from adding a symbol to the export list.
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Let the function 'sym_update_namespace' take care of updating the
namespace for a symbol. While this currently only replaces one single
location where namespaces are updated, in a following patch, this
function will get more call sites.
The function signature is intentionally close to sym_update_crc and
taking the name by char* seems like unnecessary work as the symbol has
to be looked up again. In a later patch of this series, this concern
will be addressed.
This function ensures that symbol::namespace is either NULL or has a
valid non-empty value. Previously, the empty string was considered 'no
namespace' as well and this lead to confusion.
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
While it is useful for new drivers to use devm_platform_ioremap_resource,
this script is currently used to spam maintainers, often updating very
old drivers. The net benefit is the removal of 2 lines of code in the
driver but the review load for the maintainers is huge. As of now, more
that 560 patches have been sent, some of them obviously broken, as in:
https://lore.kernel.org/lkml/9bbcce19c777583815c92ce3c2ff2586@www.loen.fr/
Remove the script to reduce the spam.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
