Instead of calling prepare_flip right before calling finish_page_flip
do everything from prepare_page_flip in finish_page_flip.
Putting prepare and finish page_flip in a single step removes the need
for INTEL_FLIP_COMPLETE, so it can be removed. This simplifies the code
slightly.
Changes since v1:
- Invert if case to simplify code.
- Add missing barrier.
- Reword commit message.
Changes since v2:
- intel_page_flip_plane is removed.
- work->pending is turned into a bool.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Both intel_unpin_work.pending and intel_unpin_work.enable_stall_check
were used to see if work should be enabled. By only using pending
some special cases are gone, and access to unpin_work can be simplified.
A flip could previously be queued before
stallcheck was active. With the addition of the pending member
enable_stall_check became obsolete and can thus be removed.
Use this to only access work members untilintel_mark_page_flip_active
is called, or intel_queue_mmio_flip is used. This will prevent
use-after-free, and makes it easier to verify accesses.
Changes since v1:
- Reword commit message.
- Do not access unpin_work after intel_mark_page_flip_active.
- Add the right memory barriers.
Changes since v2:
- atomic_read() needs a full smp_rmb.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
If the source of the backlight PWM is from the
panel then the PWM can be controlled by DCS
command, this patch adds the support to
enable/disbale panel PWM, control backlight level
etc...
v2: Moving the CABC bkl functions to new file.(Jani)
v3: Rebase
v4: Rebase
v5: Use mipi_dsi_dcs_write() instead of mipi_dsi_dcs_write_buffer() (Jani)
Move DCS macro`s to include/video/mipi_display.h (Jani)
v6: Rename the file to intel_dsi_panel_pwm.c
Removing the CABC operations
v7 by Jani: renames, rebases, etc.
v8 by Jani: s/INTEL_BACKLIGHT_CABC/INTEL_BACKLIGHT_DSI_DCS/
v9 by Jani: rename init function to intel_dsi_dcs_init_backlight_funcs
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/71238a4b14b8c3a6c04070c789f09f1b4bc00a15.1461676337.git.jani.nikula@intel.com
Backmerge request by Jani to get at
commit 249c4f538b
Author: Deepak M <m.deepak@intel.com>
Date: Wed Mar 30 17:03:39 2016 +0300
drm: Add new DCS commands in the enum list
Some simple conflicts in intel_dp.c.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Moving watermark calculation into the check phase will allow us to to
reject display configurations for which there are no valid watermark
values before we start trying to program the hardware (although those
tests will come in a subsequent patch).
Another advantage of moving this calculation to the check phase is that
we can calculate the watermarks in a single shot as part of the atomic
transaction. The watermark interfaces we inherited from our legacy
modesetting days are a bit broken in the atomic design because they use
per-crtc entry points but actually re-calculate and re-program something
that is really more of a global state. That worked okay in the legacy
modesetting world because operations only ever updated a single CRTC at
a time. However in the atomic world, a transaction can involve multiple
CRTC's, which means we wind up computing and programming the watermarks
NxN times (where N is the number of CRTC's involved). With this patch
we eliminate the redundant re-calculation of watermark data for atomic
states (which was the cause of the WARN_ON(!wm_changed) problems that
have plagued us for a while).
We still need to work on the 'commit' side of watermark handling so that
we aren't doing redundant NxN programming of watermarks, but that's
content for future patches.
v2:
- Bail out of skl_write_wm_values() if the CRTC isn't active. Now that
we set dirty_pipes to ~0 if the active pipes change (because
we need to deal with DDB changes), we can now wind up here for
disabled pipes, whereas we couldn't before.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89055
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92181
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463091100-13747-1-git-send-email-matthew.d.roper@intel.com
Calculate the DDB blocks needed to satisfy the current atomic
transaction at atomic check time. This is a prerequisite to calculating
SKL watermarks during the 'check' phase and rejecting any configurations
that we can't find valid watermarks for.
Due to the nature of DDB allocation, it's possible for the addition of a
new CRTC to make the watermark configuration already in use on another,
unchanged CRTC become invalid. A change in which CRTC's are active
triggers a recompute of the entire DDB, which unfortunately means we
need to disallow any other atomic commits from racing with such an
update. If the active CRTC's change, we need to grab the lock on all
CRTC's and run all CRTC's through their 'check' handler to recompute and
re-check their per-CRTC DDB allocations.
Note that with this patch we only compute the DDB allocation but we
don't actually use the computed values during watermark programming yet.
For ease of review/testing/bisecting, we still recompute the DDB at
watermark programming time and just WARN() if it doesn't match the
precomputed values. A future patch will switch over to using the
precomputed values once we're sure they're being properly computed.
Another clarifying note: DDB allocation itself shouldn't ever fail with
the algorithm we use today (i.e., we have enough DDB blocks on BXT to
support the minimum needs of the worst-case scenario of every pipe/plane
enabled at full size). However the watermarks calculations based on the
DDB may fail and we'll be moving those to the atomic check as well in
future patches.
v2:
- Skip DDB calculations in the rare case where our transaction doesn't
actually touch any CRTC's at all. Assuming at least one CRTC state
is present in our transaction, then it means we can't race with any
transactions that would update dev_priv->active_crtcs (which requires
_all_ CRTC locks).
v3:
- Also calculate DDB during initial hw readout, to prevent using
incorrect bios values. (Maarten)
v4:
- Use new distrust_bios_wm flag instead of skip_initial_wm (which was
never actually set).
- Set intel_state->active_pipe_changes instead of just realloc_pipes
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lyude Paul <cpaul@redhat.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-10-git-send-email-matthew.d.roper@intel.com
Reorganize the nested structures and unions we have for pipe watermark
data in intel_crtc_state so that platform-specific data can be added in
a more sensible manner (and save a bit of memory at the same time).
The change basically changes the organization from:
union {
struct intel_pipe_wm ilk;
struct intel_pipe_wm skl;
} optimal;
struct intel_pipe_wm intermediate /* ILK-only */
to
union {
struct {
struct intel_pipe_wm intermediate;
struct intel_pipe_wm optimal;
} ilk;
struct {
struct intel_pipe_wm optimal;
} skl;
}
There should be no functional change here, but it will allow us to add
more platform-specific fields going forward (and more easily extend to
other platform types like VLV).
While we're at it, let's move the entire watermark substructure out to
its own structure definition to make the code slightly more readable.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-2-git-send-email-matthew.d.roper@intel.com
Another day, another long overdue conversion. Not much to update inside
intel_overlay.c, but still
text data bss dec hex filename
6309547 3578778 696320 10584645 a18245 vmlinux
6309291 3578778 696320 10584389 a18145 vmlinux
a couple of hundred bytes of pointer misdirection.
Whilst here, rename the ioctl entry points to include the _ioctl suffix
so that the user entry points are clear (following the idiom).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463053403-25086-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
I have noticed some of our interrupt handlers use both dev and
dev_priv while they could get away with only dev_priv in the
huge majority of cases.
Tidying that up had a cascading effect on changing functions
prototypes, so relatively big churn factor, but I think it is
for the better.
For example even where changes cascade out of i915_irq.c, for
functions prefixed with intel_, genX_ or <plat>_, it makes more
sense to take dev_priv directly anyway.
This allows us to eliminate local variables and intermixed usage
of dev and dev_priv where only one is good enough.
End result is shrinkage of both source and the resulting binary.
i915.ko:
- .text 000b0899
+ .text 000b0619
Or if we look at the Gen8 display irq chain:
-00000000000006ad t gen8_irq_handler
+0000000000000663 t gen8_irq_handler
-0000000000000028 T intel_opregion_asle_intr
+0000000000000024 T intel_opregion_asle_intr
-000000000000008c t ilk_hpd_irq_handler
+000000000000007f t ilk_hpd_irq_handler
-0000000000000116 T intel_check_page_flip
+0000000000000112 T intel_check_page_flip
-000000000000011a T intel_prepare_page_flip
+0000000000000119 T intel_prepare_page_flip
-0000000000000014 T intel_finish_page_flip_plane
+0000000000000013 T intel_finish_page_flip_plane
-0000000000000053 t hsw_pipe_crc_irq_handler
+000000000000004c t hsw_pipe_crc_irq_handler
-000000000000022e t cpt_irq_handler
+0000000000000213 t cpt_irq_handler
So small shrinkage but it is all fast paths so doesn't harm.
Situation is similar in other interrupt handlers as well.
v2: Tidy intel_queue_rps_boost_for_request as well. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Try to detect the max TMDS clock limit for the DP++ adaptor (if any)
and take it into account when checking the port clock.
Note that as with the sink (HDMI vs. DVI) TMDS clock limit we'll ignore
the adaptor TMDS clock limit in the modeset path, in case users are
already "overclocking" their TMDS links. One subtle change here is that
we'll have to respect the adaptor TMDS clock limit when we decide whether
to do 12bpc or 8bpc, otherwise we might end up picking 12bpc and
accidentally driving the TMDS link out of spec even when the user chose
a mode that fits wihting the limits at 8bpc. This means you can't
"overclock" your DP++ dongle at 12bpc anymore, but you can continue to
do so at 8bpc.
Note that for simplicity we'll use the I2C access method for all dual
mode adaptors including type 2. Otherwise we'd have to start mixing
DP AUX and HDMI together. In the future we may need to do that if we
come across any board designs that don't hook up the DDC pins to the
DP++ connectors. Such boards would obviously only work with type 2
dual mode adaptors, and not type 1.
v2: Store adaptor type under indel_hdmi->dp_dual_mode
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Pass adaptor type to drm_dp_dual_mode_max_tmds_clock(),
and use it for type1 adaptors as well
Cc: stable@vger.kernel.org
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa6234 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Don't just free the connector when we get the destroy callback.
Drop a reference to it, and set it's mst_port to NULL so
no more mst work is done on it.
v2: core mst accepts NULLs fine. Cleanup EDID code properly.
v3: drop the extra reference we were taking.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I just noticed that VLV/CHV have a RAWCLK_FREQ register just like PCH
platforms. It lives in the display power well, so we should update it
when enabling the power well.
Interestingly the BIOS seems to leave it at the reset value (125) which
doesn't match the rawclk frequency on VLV/CHV (200 MHz). As always with
these register, the spec is extremely vague what the register does. All
it says is: "This is used to generate a divided down clock for
miscellaneous timers in display." Based on a quick test, at least AUX
and PWM appear to be unaffected by this.
But since the register is there, let's configure it in accordance with
the spec.
Note that we have to move intel_update_rawclk() to occur before we
touch the power wells, so that the dev_priv->rawclk_freq is already
populated when the disp2 enable hook gets called for the first time.
I think this should be safe to do on other platforms as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461768202-17544-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch adds support for eDP backlight control using DPCD registers to
backlight hooks in intel_panel.
It checks for backlight control over AUX channel capability and sets up
function pointers to get and set the backlight brightness level if
supported.
v2: Moved backlight functions from intel_dp.c into a new file
intel_dp_aux_backlight.c. Also moved reading of eDP display control
registers to intel_dp_get_dpcd
v3: Correct some formatting mistakes
v4: Updated to use AUX backlight control if PWM control is not possible
(Jani)
v5: Moved call to initialize backlight registers to dp_aux_setup_backlight
v6: Check DP_EDP_BACKLIGHT_PIN_ENABLE_CAP is disabled before setting up AUX
backlight control. To fix BLM_PWM_ENABLE igt test warnings on bdw_ultra
v7: Add enable_dpcd_backlight module parameter.
v8: Rebase onto latest drm-intel-nightly branch
v9: Remove changes to intel_dp_dpcd_read_wake
Split addition edp_dpcd variable into a separate patch
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
[Jani: whitepace changes to appease checkpatch]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459865452-9138-4-git-send-email-yetundex.adebisi@intel.com
After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.
v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-4-git-send-email-imre.deak@intel.com
While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.
v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460980101-14713-1-git-send-email-imre.deak@intel.com
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c417 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.
v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459780030-15781-1-git-send-email-imre.deak@intel.com
Power well 1 is managed by the DMC firmware so don't toggle it on-demand
from the driver. This means we need to follow the BSpec display
initialization sequence during driver loading and resuming (both system
and runtime) and enable power well 1 only once there. Afterwards DMC
will toggle power well 1 whenever entering/exiting DC5.
For this to work we also need to do away getting the PLL power domain,
since that just kept runtime PM disabled for good.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-12-git-send-email-imre.deak@intel.com
On Broxton we need to enable/disable power well 1 during the init/unit
display sequence similarly to Skylake/Kabylake. The code for this will
be added in a follow-up patch, but to prepare for that unexport
skl_pw1_misc_io_init(). It's a simple function called only from a single
place and having it inlined in the Skylake display core init/unit
functions will make it easier to compare it with its Broxton
counterpart.
This also flips the order of Misc IO and power well 1 disabling which
matches the enabling order. The specification doesn't prescribe the
disabling order, so this should be fine.
v2:
- Fix incorrect enable vs. disable power well call in
skl_display_core_uninit() (Patrik)
- Add commit comment about chaning the order of PW1 and Misc IO power
well disabling (Patrik)
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459773777-10701-1-git-send-email-imre.deak@intel.com
Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.
Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.
While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.
v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Sink count can change between short pulse hpd hence this patch
adds a member variable to intel_dp so we can track any changes
between short pulse interrupts.
This patch reads sink_count dpcd always and removes its
read operation based on values in downstream port dpcd.
SINK_COUNT dpcd is not dependent on DOWNSTREAM_PORT_PRESENT dpcd.
SINK_COUNT denotes if a display is attached, while
DOWNSTREAM_PORT_PRESET indicates how many ports are available
in the dongle where display can be attached. so it is possible
for sink count to change irrespective of value in downstream
port dpcd.
Here is a table of possible values and scenarios
sink_count downstream_port
present
0 0 no display is attached
0 1 dongle is connected without display
1 0 display connected directly
1 1 display connected through dongle
v2: Storing value of intel_dp->sink_count that is ready
for consumption. (Ander)
Squashing two commits into one. (Ander)
v3: Added comment to explain the need of early return when
sink count is 0. (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-4-git-send-email-shubhangi.shrivastava@intel.com
Current DP detection has DPCD operations split across
intel_dp_hpd_pulse and intel_dp_detect which contains
duplicates as well. Also intel_dp_detect is called
during modes enumeration as well which will result
in multiple dpcd operations. So this patch tries
to solve both these by bringing all DPCD operations
in one single function and make intel_dp_detect
use existing values instead of repeating same steps.
v2: Pulled in a hunk from last patch of the series to
this patch. (Ander)
v3: Added MST hotplug handling. (Ander)
v4: Added a flag to check if detect is performed to
prevent multiple detects on hotplug. (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
[anderco: fix parenthesis aligment]
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-2-git-send-email-shubhangi.shrivastava@intel.com
The moves a couple of functions programming the gamma LUT and CSC
units into their own file.
On generations prior to Haswell there is only a gamma LUT. From
haswell on there is also a new enhanced color correction unit that
isn't used yet. This is why we need to set the GAMMA_MODE register,
either we're using the legacy 8bits LUT or enhanced LUTs (of 10 or
12bits).
The CSC unit is only available from Haswell on.
We also need to make a special case for CherryView which is recognized
as a gen 8 but doesn't have the same enhanced color correction unit
from Haswell on.
v2: Fix access to GAMMA_MODE register on older generations than
Haswell (from Matt Roper's comments)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1458125837-2576-2-git-send-email-lionel.g.landwerlin@intel.com
The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.
The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.
v2: addressing comments by Ville:
- rename the dsi get config function to hsw_get_dsi_transcoder_state
- rebase onto the higher level split of pipe/transcoder functions
- use more has_dsi_encoder as we can now because of the above,
with no need to look at the transcoder so much
- rename IS_DSI_TRANSCODER to transcoder_is_dsi
- use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com
Split out the part initing the clock gating hooks and move it earlier.
Add a new NOP hook for platforms without the need to apply clockgating
or workaround settings, so that the hook can be called unconditionally.
Also add a WARN for future platforms that forget to add a hook.
The rest of the hooks in intel_init_pm() should be inited in the same
way, but atm some of the hooks are set only conditionally, so before
doing this we need to make the setup unconditional and use instead some
flags.
v2:
- add a NOP hook and WARN if no hook is set for the platform (Chris)
- use the term hook instead of callback for these functions (Jani)
v3:
- remove the GEN4() check it's already covered by earlier platform
checks (Chris)
CC: Jani Nikula <jani.nikula@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-6-git-send-email-imre.deak@intel.com
