commit a501ab75e7 upstream.
There is a race in pty_write(). pty_write() can be called in parallel
with e.g. ioctl(TIOCSTI) or ioctl(TCXONC) which also inserts chars to
the buffer. Provided, tty_flip_buffer_push() in pty_write() is called
outside the lock, it can commit inconsistent tail. This can lead to out
of bounds writes and other issues. See the Link below.
To fix this, we have to introduce a new helper called
tty_insert_flip_string_and_push_buffer(). It does both
tty_insert_flip_string() and tty_flip_buffer_commit() under the port
lock. It also calls queue_work(), but outside the lock. See
71a174b39f (pty: do tty_flip_buffer_push without port->lock in
pty_write) for the reasons.
Keep the helper internal-only (in drivers' tty.h). It is not intended to
be used widely.
Link: https://seclists.org/oss-sec/2022/q2/155
Fixes: 71a174b39f (pty: do tty_flip_buffer_push without port->lock in pty_write)
Cc: 一只狗 <chennbnbnb@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220707082558.9250-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f532c1e25 upstream.
Functions tty_termios_encode_baud_rate() and uart_update_timeout() should
be called with the baudrate value which was set to hardware. Linux then
report exact values via ioctl(TCGETS2) to userspace.
Change mvebu_uart_baud_rate_set() function to return baudrate value which
was set to hardware and propagate this value to above mentioned functions.
With this change userspace would see precise value in termios c_ospeed
field.
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Cc: stable <stable@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220628100922.10717-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9b11229b7 upstream.
When console is enabled, univ8250_console_setup() calls
serial8250_console_setup() before .dev is set to uart_port. Therefore,
it will not call pm_runtime_get_sync(). Later, when the actual driver
is going to take over univ8250_console_exit() is called. As .dev is
already set, serial8250_console_exit() makes pm_runtime_put_sync() call
with usage count being zero triggering PM usage count warning
(extra debug for univ8250_console_setup(), univ8250_console_exit(), and
serial8250_register_ports()):
[ 0.068987] univ8250_console_setup ttyS0 nodev
[ 0.499670] printk: console [ttyS0] enabled
[ 0.717955] printk: console [ttyS0] printing thread started
[ 1.960163] serial8250_register_ports assigned dev for ttyS0
[ 1.976830] printk: console [ttyS0] disabled
[ 1.976888] printk: console [ttyS0] printing thread stopped
[ 1.977073] univ8250_console_exit ttyS0 usage:0
[ 1.977075] serial8250 serial8250: Runtime PM usage count underflow!
[ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A
[ 1.977812] univ8250_console_setup ttyS0 usage:2
[ 1.978167] printk: console [ttyS0] printing thread started
[ 1.978203] printk: console [ttyS0] enabled
To fix the issue, call pm_runtime_get_sync() in
serial8250_register_ports() as soon as .dev is set for an uart_port
if it has console enabled.
This problem became apparent only recently because 82586a7215 ("PM:
runtime: Avoid device usage count underflows") added the warning
printout. I confirmed this problem also occurs with v5.18 (w/o the
warning printout, obviously).
Fixes: bedb404e91 ("serial: 8250_port: Don't use power management for kernel console")
Cc: stable <stable@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/b4f428e9-491f-daf2-2232-819928dc276e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e690d54cf upstream.
If port->mapbase = NULL in serial8250_request_std_resource() , it need
return a error code instead of 0. If uart_set_info() fail to request new
regions by serial8250_request_std_resource() but the return value of
serial8250_request_std_resource() is 0, The system incorrectly considers
that the resource application is successful and does not attempt to
restore the old setting. A null pointer reference is triggered when the
port resource is later invoked.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220628083515.64138-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39cdb68c64 upstream.
A memory overlapping copy occurs when deleting a long line. This memory
overlapping copy can cause data corruption when scr_memcpyw is optimized
to memcpy because memcpy does not ensure its behavior if the destination
buffer overlaps with the source buffer. The line buffer is not always
broken, because the memcpy utilizes the hardware acceleration, whose
result is not deterministic.
Fix this problem by using replacing the scr_memcpyw with scr_memmovew.
Fixes: 81732c3b2f ("tty vt: Fix line garbage in virtual console on command line edition")
Cc: stable <stable@kernel.org>
Signed-off-by: Yangxi Xiang <xyangxi5@gmail.com>
Link: https://lore.kernel.org/r/20220628093322.5688-1-xyangxi5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57435c4240 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.1.2 describes the encoding of the
C/R (command/response) bit. Table 1 shows that the actual encoding of the
C/R bit is inverted if the associated frame is sent by the responder.
The referenced commit fixed here further broke the internal meaning of this
bit in the outgoing path by always setting the C/R bit regardless of the
frame type.
This patch fixes both by setting the C/R bit always consistently for
command (1) and response (0) frames and inverting it later for the
responder where necessary. The meaning of this bit in the debug output
is being preserved and shows the bit as if it was encoded by the initiator.
This reflects only the frame type rather than the encoded combination of
communication side and frame type.
Fixes: cc0f42122a ("tty: n_gsm: Modify CR,PF bit when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9361ebfbb7 ]
gsmtty_write() does not prevent the user to use the full fifo size of 4096
bytes as allocated in gsm_dlci_alloc(). However, gsmtty_write_room() tries
to limit the return value by 'TX_SIZE' and returns a negative value if the
fifo has more than 'TX_SIZE' bytes stored. This is obviously wrong as
'TX_SIZE' is defined as 512.
Define 'TX_SIZE' to the fifo size and use it accordingly for allocation to
keep the current behavior. Return the correct remaining size of the fifo in
gsmtty_write_room() via kfifo_avail().
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c19ffe00fe ]
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 states that the Modem Status
Command (MSC) shall only be used if the basic option was chosen.
The current implementation uses MSC frames even if advanced option was
chosen to inform the peer about modem line state updates. A standard
conform peer may choose to discard these frames in advanced option mode.
Furthermore, gsmtty_modem_update() is not part of the 'tty_operations'
functions despite its name.
Rename gsmtty_modem_update() to gsm_modem_update() to clarify this. Split
its function into gsm_modem_upd_via_data() and gsm_modem_upd_via_msc()
depending on the encoding and adaption. Introduce gsm_dlci_modem_output()
as adaption of gsm_dlci_data_output() to encode and queue empty frames in
advanced option mode. Use it in gsm_modem_upd_via_data().
gsm_modem_upd_via_msc() is based on the initial gsmtty_modem_update()
function which used only MSC frames to update modem states.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a0e4b1733 ]
The frame checksum (FCS) is currently handled in gsm_queue() after
reception of a frame. However, this breaks layering. A workaround with
'received_fcs' was implemented so far.
Furthermore, frames are handled as such even if no end flag was received.
Move FCS calculation from gsm_queue() to gsm0_receive() and gsm1_receive().
Also delay gsm_queue() call there until a full frame was received to fix
both points.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 927728a34f ]
We tested RS485 function on an EVB which has SC16IS752, after
finishing the test, we started the RS232 function test, but found the
RTS is still working in the RS485 mode.
That is because both startup and shutdown call port_update() to set
the EFCR_REG, this will not clear the RS485 bits once the bits are set
in the reconf_rs485(). To fix it, clear the RS485 bits in shutdown.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220308110042.108451-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2dd8a74fdd upstream.
RTS polarity of rs485-enabled ports is currently initialized on uart
open via:
tty_port_open()
tty_port_block_til_ready()
tty_port_raise_dtr_rts() # if (C_BAUD(tty))
uart_dtr_rts()
uart_port_dtr_rts()
There's at least three problems here:
First, if no baud rate is set, RTS polarity is not initialized.
That's the right thing to do for rs232, but not for rs485, which
requires that RTS is deasserted unconditionally.
Second, if the DeviceTree property "linux,rs485-enabled-at-boot-time" is
present, RTS should be deasserted as early as possible, i.e. on probe.
Otherwise it may remain asserted until first open.
Third, even though RTS is deasserted on open and close, it may
subsequently be asserted by uart_throttle(), uart_unthrottle() or
uart_set_termios() because those functions aren't rs485-aware.
(Only uart_tiocmset() is.)
To address these issues, move RTS initialization from uart_port_dtr_rts()
to uart_configure_port(). Prevent subsequent modification of RTS
polarity by moving the existing rs485 check from uart_tiocmget() to
uart_update_mctrl().
That way, RTS is initialized on probe and then remains unmodified unless
the uart transmits data. If rs485 is enabled at runtime (instead of at
boot) through a TIOCSRS485 ioctl(), RTS is initialized by the uart
driver's ->rs485_config() callback and then likewise remains unmodified.
The PL011 driver initializes RTS on uart open and prevents subsequent
modification in its ->set_mctrl() callback. That code is obsoleted by
the present commit, so drop it.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2d2acaf3a69e89b7bf687c912022b11fd29dfa1e.1642909284.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62b2caef40 ]
There is a deadlock in sa1100_set_termios(), which is shown
below:
(Thread 1) | (Thread 2)
| sa1100_enable_ms()
sa1100_set_termios() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | sa1100_timeout()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417111626.7802-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 689ca31c54 ]
When the driver fails at alloc_hdlcdev(), and then we remove the driver
module, we will get the following splat:
[ 25.065966] general protection fault, probably for non-canonical address 0xdffffc0000000182: 0000 [#1] PREEMPT SMP KASAN PTI
[ 25.066914] KASAN: null-ptr-deref in range [0x0000000000000c10-0x0000000000000c17]
[ 25.069262] RIP: 0010:detach_hdlc_protocol+0x2a/0x3e0
[ 25.077709] Call Trace:
[ 25.077924] <TASK>
[ 25.078108] unregister_hdlc_device+0x16/0x30
[ 25.078481] slgt_cleanup+0x157/0x9f0 [synclink_gt]
Fix this by checking whether the 'info->netdev' is a null pointer first.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220410114814.3920474-1-zheyuma97@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1deeda8d28 ]
Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c8a9d04394 (serial: stm32: fix word length configuration)
Cc: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c069d2756c ]
Only CS8 is supported but CSIZE was not sanitized to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Similarly, INPCK, PARMRK, and BRKINT are reported textually unsupported
but were not cleared in termios c_iflag which is the machine-readable
format.
Fixes: 45c054d081 (tty: serial: add driver for the SiFive UART)
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 098333a9c7 ]
Only CS7 and CS8 are supported but CSIZE is not sanitized after
fallthrough from CS5 or CS6 to CS7.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c10b13325c (tty: serial: Add RDA8810PL UART driver)
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0258502f11 ]
drivers/tty/serial/cpm_uart/cpm_uart_core.c: In function ‘cpm_uart_init_port’:
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1251:7: error: ‘udbg_port’ undeclared (first use in this function); did you mean ‘uart_port’?
if (!udbg_port)
^~~~~~~~~
uart_port
commit d142585bce leave this corner, wrap it with #ifdef block
Fixes: d142585bce ("serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20220518135452.39480-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af01792709 ]
SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND relate to behavior
within RS485 operation. The driver checks if they have the same value
which is not possible to realize with the hardware. The check is taken
regardless of SER_RS485_ENABLED flag and -EINVAL is returned when the
check fails, which creates problems.
This check makes it unnecessarily complicated to turn RS485 mode off as
simple zeroed serial_rs485 struct will trigger that equal values check.
In addition, the driver itself memsets its rs485 structure to zero when
RS485 is disabled but if userspace would try to make an TIOCSRS485
ioctl() call with the very same struct, it would end up failing with
-EINVAL which doesn't make much sense.
Resolve the problem by moving the check inside SER_RS485_ENABLED block.
Fixes: 7ecc77011c ("serial: 8250_fintek: Return -EINVAL on invalid configuration")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/035c738-8ea5-8b17-b1d7-84a7b3aeaa51@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 589f892ac8 ]
The uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
Since the startup() callback is reading/writing registers used by
the console write() callback (AML_UART_CONTROL), its access must
be synchronized using the port->lock. Currently it is not.
The startup() callback is the only function that explicitly enables
interrupts. Without the synchronization, it is possible that
interrupts become accidentally permanently disabled.
CPU0 CPU1
meson_serial_console_write meson_uart_startup
-------------------------- ------------------
spin_lock(port->lock)
val = readl(AML_UART_CONTROL)
uart_console_write()
writel(INT_EN, AML_UART_CONTROL)
writel(val, AML_UART_CONTROL)
spin_unlock(port->lock)
Add port->lock synchronization to meson_uart_startup() to avoid
racing with meson_serial_console_write().
Also add detailed comments to meson_uart_reset() explaining why it
is *not* using port->lock synchronization.
Link: https://lore.kernel.org/lkml/2a82eae7-a256-f70c-fd82-4e510750906e@samsung.com
Fixes: ff7693d079 ("ARM: meson: serial: add MesonX SoC on-chip uart driver")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20220508103547.626355-1-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 925ea0fa52 ]
The module param debug for n_gsm uses KERN_INFO level, but the hexdump
now uses KERN_DEBUG level. This started after commit 091cb0994e
("lib/hexdump: make print_hex_dump_bytes() a nop on !DEBUG builds").
We now use dynamic_hex_dump() unless DEBUG is set.
This causes no packets to be seen with modprobe n_gsm debug=0x1f unlike
earlier. Let's fix this by adding gsm_hex_dump_bytes() that calls
print_hex_dump() with KERN_INFO to match what n_gsm is doing with the
other debug related output.
Fixes: 091cb0994e ("lib/hexdump: make print_hex_dump_bytes() a nop on !DEBUG builds")
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220512131506.1216-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a7ff843d5 ]
The base baud value reported is supposed to be the highest baud rate
that can be set for a serial port. The SiFive FU740-C000 SOC's on-chip
UART supports baud rates of up to 1/16 of the input clock rate, which is
the bus clock `tlclk'[1], often at 130MHz in the case of the HiFive
Unmatched board.
However the sifive UART driver reports a fixed value of 115200 instead:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
even though we already support setting higher baud rates, e.g.:
$ tty
/dev/ttySIF1
$ stty speed
230400
The baud base value is computed by the serial core by dividing the UART
clock recorded in `struct uart_port' by 16, which is also the minimum
value of the clock divider supported, so correct the baud base value
reported by setting the UART clock recorded to the input clock rate
rather than 115200:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 8125000) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 8125000) is a SiFive UART v0
References:
[1] "SiFive FU740-C000 Manual", v1p3, SiFive, Inc., August 13, 2021,
Section 16.9 "Baud Rate Divisor Register (div)", pp.143-144
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1f1496a923 ("riscv: Fix sifive serial driver")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204291656280.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f398e0aa32 ]
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65a8b28702 ]
TTYs in ICANON mode have a special case that allows "pushing" a line
without a regular EOL character (like newline), by using EOF (the EOT
character - ASCII 0x4) as a pseudo-EOL. It is silently discarded, so
the reader of the PTS will receive the line *without* EOF or any other
terminating character.
This special case has an edge case: What happens if the readers buffer
is the same size as the line (without EOF)? Will they be able to tell
if the whole line is received, i.e. if the next read() will return more
of the same line or the next line?
There are two possibilities, that both have (dis)advantages:
1. The next read() returns 0. FreeBSD (13.0) and OSX (10.11) do this.
Advantage: The reader can interpret this as "the line is over".
Disadvantage: read() returning 0 means EOF, the reader could also
interpret it as "there's no more data" and stop reading or even
close the PT.
2. The next read() returns the next line, the EOF is silently discarded.
Solaris (or at least OpenIndiana 2021.10) does this, Linux has done
do this since commit 40d5e0905a ("n_tty: Fix EOF push handling");
this behavior was recently broken by commit 3593030761 ("tty:
n_tty: do not look ahead for EOL character past the end of the buffer").
Advantage: read() won't return 0 (EOF), reader less likely to be
confused (and things like `while(read(..)>0)` don't break)
Disadvantage: The reader can't really know if the read() continues
the last line (that filled the whole read buffer) or starts a
new line.
As both options are defensible (and are used by other Unix-likes), it's
best to stick to the "old" behavior since "n_tty: Fix EOF push handling"
of 2013, i.e. silently discard that EOF.
This patch - that I actually got from Linus for testing and only
modified slightly - restores that behavior by skipping an EOF
character if it's the next character after reading is done.
Based on a patch from Linus Torvalds.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Fixes: 3593030761 ("tty: n_tty: do not look ahead for EOL character past the end of the buffer")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Reviewed-and-tested-by: Daniel Gibson <daniel@gibson.sh>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Gibson <daniel@gibson.sh>
Link: https://lore.kernel.org/r/20220329235810.452513-2-daniel@gibson.sh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
