commit 736cd79f48 upstream.
So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.
The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81ccb2a69f upstream.
Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89c043a6cb upstream.
Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffa34de03b upstream.
SMSC IrCC SIR/FIR port should not be bound to by
(legacy) serial driver so its own driver (smsc-ircc2)
can bind to it.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8117e34740 upstream.
Fix panic caused by a race between men_z135_intr() and men_z135_set_termios().
men_z135_intr() and men_z135_set_termios() both hold the struct uart_port::lock
spinlock, but men_z135_intr() does a spin_lock_irqsave() and
men_z135_set_termios() does a normal spin_lock(), which can lead to a deadlock
when an interrupt is called while the lock is being helt by
men_z135_set_termios().
This was discovered using a insmod, hardware looppback send/receive, rmmod
stress test.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b19e03229 upstream.
When handling signalling char, claim the termios write lock before
signalling waiting readers and writers to prevent further i/o
before flushing the echo and output buffers. This prevents a
userspace signal handler which may output from racing the terminal
flush.
Reference: Bugzilla #99351 ("Output truncated in ssh session after...")
Fixes: commit d2b6f44779 ("n_tty: Fix signal handling flushes")
Reported-by: Filipe Brandenburger <filbranden@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e144c58cad upstream.
While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:
CPU 0 | CPU 1
|
uart_close() |
tty_port_close_start() |
tty->closing = 1 |
tty_ldisc_flush() |
| => IRQ
| while (LSR & data ready)
| uart_insert_char()
| tty_flip_buffer_push()
| <= EOI
stop_rx() | .
uart_shutdown() | .
free xmit.buf | .
tty_port_tty_set(NULL) | .
tty->closing = 0 | .
| flush_to_ldisc()
| n_tty_receive_buf_common()
| __receive_buf()
| ...
| commit_echoes()
| uart_flush_chars()
| __uart_start()
| ** OOPS on port.tty deref **
tty_ldisc_flush() |
Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().
[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.
Fixes: 2e75891083 ("serial: core: Flush ldisc after dropping port
mutex in uart_close()")
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 907eda32a3 upstream.
This reverts commit 068500e08d.
According to some tests, SDMA support is broken at least for i.MX6 without
HW flow control. Different forms of data-corruption appear either with
the ROM firmware for the SDMA controller as well as when loading Freescale
provided SDMA firmware versions 1.1 or 3.1.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffb6e0c9a0 upstream.
The platform_sysrq_reset_seq code was intended as a way for an embedded
platform to provide its own sysrq sequence at compile time. After over two
years, nobody has started using it in an upstream kernel, and the platforms
that were interested in it have moved on to devicetree, which can be used
to configure the sequence without requiring kernel changes. The method is
also incompatible with the way that most architectures build support for
multiple platforms into a single kernel.
Now the code is producing warnings when built with gcc-5.1:
drivers/tty/sysrq.c: In function 'sysrq_init':
drivers/tty/sysrq.c:959:33: warning: array subscript is above array bounds [-Warray-bounds]
key = platform_sysrq_reset_seq[i];
We could fix this, but it seems unlikely that it will ever be used, so
let's just remove the code instead. We still have the option to pass the
sequence either in DT, using the kernel command line, or using the
/sys/module/sysrq/parameters/reset_seq file.
Fixes: 154b7a489a ("Input: sysrq - allow specifying alternate reset sequence")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 357d561519 upstream.
A configuration that enables earlycon but not the core console
code causes a link error:
drivers/built-in.o: In function `setup_earlycon':
drivers/tty/serial/earlycon.c:70: undefined reference to `uart_parse_earlycon'
That error can be triggered by the newly added samsung earlycon support,
which is missing a 'select' statement.
As suggested by Peter Hurley, solves the problem by moving the
'select SERIAL_EARLYCON' statement to the samsung console driver
option, as it is done by all other console drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b94ba0328d ("serial: samsung: Add support for early console")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8687634b79 upstream.
In RS485 mode, we may want to set the delay_rts_after_send value to 0.
In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but
this is exactly the expected behavior if we want no delay...
Moreover, if the value was set to non-zero value by device-tree or earlier
ioctl command, it was impossible to change it back to zero.
Reported-by: Sami Pietikäinen <Sami.Pietikainen@wapice.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial driver fixes from Greg KH:
"Here are a few TTY and Serial driver fixes for reported regressions
and crashes.
All of these have been in linux-next with no reported problems"
* tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
n_tty: Fix auditing support for cannonical mode
serial: 8250_omap: provide complete custom startup & shutdown callbacks
n_tty: Fix calculation of size in canon_copy_from_read_buf
serial: imx: Fix DMA handling for IDLE condition aborts
serial/amba-pl011: Unconditionally poll for FIFO space before each TX char
Commit 32f13521ca
("n_tty: Line copy to user buffer in canonical mode")
changed cannonical mode copying to use copy_to_user
but missed adding the call to the audit framework.
Add in the appropriate functions to get audit support.
Fixes: 32f13521ca ("n_tty: Line copy to user buffer in canonical mode")
Reported-by: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d118 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a hardcoded value of 4096 which should have been N_TTY_BUF_SIZE.
This caused reads from tty to fail with EFAULT when they shouldn't have
done if N_TTY_BUF_SIZE was declared to be something other than 4096.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.
This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.
Reported-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 734745caeb serial/amba-pl011:
(Activate TX IRQ passively) introduces a race which causes the driver
sometimes to attempt to write a character to the TX FIFO when the FIFO
is already full.
The PL011 does not guarantee its behaviour when the FIFO is overfilled.
In practice, this can cause duplicate and/or dropped characters to be
output on the wire. The problem is common enough to be readily
observable on the ARM Juno platform when the PL011 UART is used as
the console and DMA is not in use.
This patch fixes this problem by always polling for space before each
character is written to the FIFO.
This will be amended to a less brute-force approach in a later commit,
but this patch should help ensure correct behaviour for now.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull two xen bugfixes from David Vrabel:
- fix ARM build regression.
- fix VIRQ_CONSOLE related oops.
* tag 'for-linus-4.1b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: don't bind non-percpu VIRQs with percpu chip
xen/arm: Define xen_arch_suspend()
A non-percpu VIRQ (e.g., VIRQ_CONSOLE) may be freed on a different
VCPU than it is bound to. This can result in a race between
handle_percpu_irq() and removing the action in __free_irq() because
handle_percpu_irq() does not take desc->lock. The interrupt handler
sees a NULL action and oopses.
Only use the percpu chip/handler for per-CPU VIRQs (like VIRQ_TIMER).
# cat /proc/interrupts | grep virq
40: 87246 0 xen-percpu-virq timer0
44: 0 0 xen-percpu-virq debug0
47: 0 20995 xen-percpu-virq timer1
51: 0 0 xen-percpu-virq debug1
69: 0 0 xen-dyn-virq xen-pcpu
74: 0 0 xen-dyn-virq mce
75: 29 0 xen-dyn-virq hvc_console
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: <stable@vger.kernel.org>
Pull tty/serial fixes from Greg KH:
"Here's some TTY and serial driver fixes for reported issues.
All of these have been in linux-next successfully"
* tag 'tty-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pty: Fix input race when closing
tty/n_gsm.c: fix a memory leak when gsmtty is removed
Revert "serial/amba-pl011: Leave the TX IRQ alone when the UART is not open"
serial: omap: Fix error handling in probe
earlycon: Revert log warnings
A read() from a pty master may mistakenly indicate EOF (errno == -EIO)
after the pty slave has closed, even though input data remains to be read.
For example,
pty slave | input worker | pty master
| |
| | n_tty_read()
pty_write() | | input avail? no
add data | | sleep
schedule worker --->| | .
|---> flush_to_ldisc() | .
pty_close() | fill read buffer | .
wait for worker | wakeup reader --->| .
| read buffer full? |---> input avail ? yes
|<--- yes - exit worker | copy 4096 bytes to user
TTY_OTHER_CLOSED <---| |<--- kick worker
| |
**** New read() before worker starts ****
| | n_tty_read()
| | input avail? no
| | TTY_OTHER_CLOSED? yes
| | return -EIO
Several conditions are required to trigger this race:
1. the ldisc read buffer must become full so the input worker exits
2. the read() count parameter must be >= 4096 so the ldisc read buffer
is empty
3. the subsequent read() occurs before the kicked worker has processed
more input
However, the underlying cause of the race is that data is pipelined, while
tty state is not; ie., data already written by the pty slave end is not
yet visible to the pty master end, but state changes by the pty slave end
are visible to the pty master end immediately.
Pipeline the TTY_OTHER_CLOSED state through input worker to the reader.
1. Introduce TTY_OTHER_DONE which is set by the input worker when
TTY_OTHER_CLOSED is set and either the input buffers are flushed or
input processing has completed. Readers/polls are woken when
TTY_OTHER_DONE is set.
2. Reader/poll checks TTY_OTHER_DONE instead of TTY_OTHER_CLOSED.
3. A new input worker is started from pty_close() after setting
TTY_OTHER_CLOSED, which ensures the TTY_OTHER_DONE state will be
set if the last input worker is already finished (or just about to
exit).
Remove tty_flush_to_ldisc(); no in-tree callers.
Fixes: 52bce7f8d4 ("pty, n_tty: Simplify input processing on final close")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96311
BugLink: http://bugs.launchpad.net/bugs/1429756
Cc: <stable@vger.kernel.org> # 3.19+
Reported-by: Andy Whitcroft <apw@canonical.com>
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when gsmtty_remove put dlci, it will cause memory leak if dlci->port's refcount is zero.
So we do the cleanup work in .cleanup callback instead.
dlci will be last put in two call chains.
1) gsmld_close -> gsm_cleanup_mux -> gsm_dlci_release -> dlci_put
2) gsmld_remove -> dlci_put
so there is a race. the memory leak depends on the race.
In call chain 2. we hit the memory leak. below comment tells.
release_tty -> tty_driver_remove_tty -> gsmtty_remove -> dlci_put -> tty_port_destructor (WARN_ON(port->itty) and return directly)
|
tty->port->itty = NULL;
|
tty_kref_put ---> release_one_tty -> gsmtty_cleanup (added by our patch)
So our patch fix the memory leak by doing the cleanup work after tty core did.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Fixes: dfabf7ffa3
Cc: stable <stable@vger.kernel.org> # 3.14+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2ee6dfa0e.
Jakub Kiciński observed that this patch can cause the pl011
driver to hang if if the only process with a pl011 port open is
killed by a signal, pl011_shutdown() can get called with an
arbitrary amount of data still in the FIFO.
Calling _shutdown() with the TX FIFO non-empty is questionable
behaviour and my itself be a bug.
Since the affected patch was speculative anyway, and brings limited
benefit, the simplest course is to remove the assumption that TXIS
will always be left asserted after the port is shut down.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is pm_qos_add_request() being executed on serial_omap_probe(),
which stores "&up->pm_qos_request" from omap-serial driver to
"pm_qos_array[PM_QOS_CPU_DMA_LATENCY]->constraints". If
serial_omap_probe() fails after pm_qos_add_request() (e.g. on
uart_add_one_port() call), pm_qos_array still keeping pm_qos_request
struct from omap-serial driver, which is not valid anymore (since driver
failed). This leads further to kernel crash on pm_qos_update_target(),
executing from some completely different driver.
We were observing this while trying to run audio playback while having
one of omap-serial driver instances failed on uart_add_one_port() call:
Unable to handle kernel paging request at virtual address fffffffc
Backtrace:
(plist_add) from (pm_qos_update_target)
(pm_qos_update_target) from (pm_qos_add_request)
(pm_qos_add_request) from (snd_pcm_hw_params)
(snd_pcm_hw_params) from (snd_pcm_common_ioctl1)
(snd_pcm_common_ioctl1) from (snd_pcm_playback_ioctl1)
(snd_pcm_playback_ioctl1) from (snd_pcm_playback_ioctl)
(snd_pcm_playback_ioctl) from (do_vfs_ioctl)
(do_vfs_ioctl) from (SyS_ioctl)
(SyS_ioctl) from (ret_fast_syscall)
This patch adds pm_qos_remove_request() on fail path in
serial_omap_probe() in order to fix this issue. While at it, free the
wakeup settings on fail path as well, just like it's done in
serial_omap_remove().
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull xen bug fixes from David Vrabel:
- fix blkback regression if using persistent grants
- fix various event channel related suspend/resume bugs
- fix AMD x86 regression with X86_BUG_SYSRET_SS_ATTRS
- SWIOTLB on ARM now uses frames <4 GiB (if available) so device only
capable of 32-bit DMA work.
* tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Add __GFP_DMA flag when xen_swiotlb_init gets free pages on ARM
hypervisor/x86/xen: Unset X86_BUG_SYSRET_SS_ATTRS on Xen PV guests
xen/events: Set irq_info->evtchn before binding the channel to CPU in __startup_pirq()
xen/console: Update console event channel on resume
xen/xenbus: Update xenbus event channel on resume
xen/events: Clear cpu_evtchn_mask before resuming
xen-pciback: Add name prefix to global 'permissive' variable
xen: Suspend ticks on all CPUs during suspend
xen/grant: introduce func gnttab_unmap_refs_sync()
xen/blkback: safely unmap purge persistent grants
The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).
Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.
See: https://www.exar.com/common/content/document.ashx?id=1587 page 11
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes problems with serial console break. When function
s3c64xx_serial_startup() was started while serial console has been working,
it caused lose of characters written to TX FIFO. This effect was particularly
observable with systemd, which closes serial port every time when it's
not currently needed, hence function s3c64xx_serial_startup() is called
quite often there. To fix this problem we avoid resetting TX FIFO if port is
used as serial console.
Example of broken console log:
[ 1086.7 Expecting device dev-ttySAC1.device...
[ 1086.[ OK ] Reached target Paths.
[ 1086.756416] s[ OK ] Reached target Swap.
[ 1086.776413] systemd[1]: Reached target Swap.
[ 1086.776642] systemd[1]: Starting Root Slice.
[ 5.53403[ OK ] Created slice Root Slice.
[ 5.548433] systemd[1]: Create[ OK ] Created slice User and Session Slice.
[ 5.568414] sys[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 5.588388] s[ OK ] Listening on Delayed Shutdown Socket.
[ 5.608376] sy[ OK ] Listening on Journal Socket (/dev/log).
[ 5.628361] [ OK ] Listening on udev Kernel Socket.
[ 5.648357] s[ OK ] Listening on udev Control Socket.
[ 5.668353] s[ OK ] Listening on Journal Socket.
[ 5.688366] systemd[1]: Listeni[ OK ] Created slice System Slice.
[ 5.708393] Mounting Temporary Directory...
[ 7139.067436] Starting prepare device daemon...
[ 7139.091726] sy Starting Generate environment from /etc/profile.d...
[ 5.792867] system Starting Create Static Device Nodes in /dev...
[ 7848.718 Mounting Debug File System...
[ 7848.7384 Mounting Configuration File System...
[ 5.852 Starting Apply Kernel Variables...
[ 5.8720 Starting Setup Virtual Console...
[ 7848.798 Starting udev Coldplug all Devices...
[ 7848.817 Starting Journal Service...
[ OK ] Started Journal Service.
[ 7848.854222] s[ OK ] Reached target Slices.
Starting Remount Root and Kernel File Systems...
[ OK ] Mounted Configuration File System.
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.
When PORT_UNKNOWN is setup probe will fail anyway.
Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"
This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.
Fix both xilinx serial drivers in the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
If the device node has a "big-endian" property and 32-bit registers, tell
the serial driver to use UPIO_MEM32BE instead of UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Pull workqueue updates from Tejun Heo:
"Workqueue now prints debug information at the end of sysrq-t which
should be helpful when tracking down suspected workqueue stalls. It
only prints out the ones with something currently going on so it
shouldn't add much output in most cases"
* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Reorder sysfs code
percpu: Fix trivial typos in comments
workqueue: dump workqueues on sysrq-t
workqueue: keep track of the flushing task and pool manager
workqueue: make the workqueues list RCU walkable
* pnp:
PNP: Avoid leaving unregistered device objects in lists
PNP: Convert pnp_lock into a mutex
PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver
PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver
PNP: net/sb1000: Use module_pnp_driver to register driver
PNP: media/rc: Use module_pnp_driver to register driver
PNP: ide/ide-pnp: Use module_pnp_driver to register driver
PNP: ata/pata_isapnp: Use module_pnp_driver to register driver
PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver
PNP: Add helper macro for pnp_register_driver boilerplate
PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
The result of netdev_priv is already implicitly cast to the type of the
left side of the assignment.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T *x;
@@
x =
- (T *)
netdev_priv(...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware is capable of inverting RTS signal when working
in RS-485 mode. Expose this functionality to user space.
Relay on a matching combination of standard flags
(SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND) to
detect when user space is requesting inverted RTS mode.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial ports of F81504/F81508/F81512 will failed when wakeup from S3(STR).
It's due to when the system wakeup from S3(STR), this PCI device's
configuration space from 0x40 to 0x40 + max_port * 0x08 should be
re-configured.
We move all initialization from pci_fintek_setup() to pci_fintek_init() and
set it to pci_serial_quirks .init section. It's will re-init this device when
system wakeup from pciserial_resume_ports().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the expected behavior of kernel command lines of the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
and
earlycon=uart[8250],io|mmio|mmio32,<addr>[,options]
earlycon=uart[8250],<addr>[,options]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore undocumented behavior of kernel command line parameters of
the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
where 'options' have not been specified; in this case, the hardware
is assumed to be initialized.
Fixes: c7cef0a849 ("console: Add extensible console matching")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
