[Why]
This option can vary depending on the panel and may be required to be
called during sink detection phase before transmitter control.
[How]
Allow modify the bit depending on the eDP panel connected with a new
interface.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If optimized init is done in FW. DCN init can be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.
[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise we can be out of sync with what's in the hardware, leading
to us rerunning every command that's presently in the ringbuffer.
[How]
Reset software state for the mailboxes in hw_reset callback.
This is already done as part of the mailbox init in hw_init, but we
do need to remember to reset the last cached wptr value as well here.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Adding the new DPIA NOTIFY packets from DMUB
As per the design with Cruise to account for
250ms response delay otherwise
[HOW]
Added th DPIA NOTIFY logic as per DMUB logic
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dpia hpd interrupt processing is disabled when entering S4/S0i3 and
would be reenabled after detection completes during resuming. Because,
keeping hpd interrupts enabled during detection leads to multiple
detections for the same hpd transition. There is a S4 case where dpia
hpd interrupt is missed when driver is in transitioning from hpd
interrupt processing disable to enable and the display does not light
up.
[How]
- Added dmub inbox command DMUB_CMD__DPIA_HPD_INT_ENABLE to explicitly
control dmub to issue dpia hpd interrupt or not. If dpia hpd interrupt
is disabled, dmub will keep the hpd pending and post it once driver
reenables dpia hpd interrupt or when querying with
DMUB_CMD__QUERY_HPD_STATE.
- Added dmub boot option dpia_hpd_int_enable_supported to notify dmub
about whether DMUB_CMD__DPIA_HPD_INT_ENABLE command would be used.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit cleans up code that uses old variables and adds some SMU
interfaces for future flexibility.
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
On wake from S3/S4, driver checks if DMUB is initialized. On S4 VBIOS loads
DMUB, and driver does not reload as it appears to be initialized already.
[How?]
Add a check for the DAL_FW bit to ensure that loaded FW is from driver and
not VBIOS.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMUB Outbox0 read/write pointer not sync after resumed from S4.
And that caused old traces were sent to outbox.
[How]
Disable DMUB Outbox0 interrupt
and clear DMUB Outbox0 read/write pointer when resumes from S4.
And then enable Outbox0 interrupt before starts DMCUB.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Very low rate to cause memory access issue while resetting
DMCUB after the halt command was sent to it.
The process of stopping fw of DMCUB may be timeout, that means
it is not in idle state, such as the window frames may still be
kept in cache, so reset by force will cause MMHUB hang.
[HOW]
After the halt command was sent, keep checking the DMCUB state until
it is idle.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: hengzhou <Hengyong.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Boot up behaviour may differ depending on the Connection Manager
handling USB4 tunneling.
[How]
Send boot option to firmware to indicate Connection Manager.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're currently flushing commands that had been previously been
flushed or are currently being processed by the DMCUB when we don't
immediately wait for idle after command execution.
[How]
Avoiding reflushing the data by keeping track of the last wptr.
We'll treat this as the actual rptr by creating a copy of the inbox
and modifying the copy's rptr.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DC we want to wait for the INBOX0 HW Lock command to ACK before
continuing. This is to ensure that the lock has been successfully
acquired before programming HW in DC.
[How]
Add interfaces to send messages on INBOX0, poll for their completation
and clear the ack.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A built firmware binary may be aligned to 16-bytes with padding at the
end as necessary. In the case that padding was applied the meta info
will not be detected correctly and we won't be able to allocate the
appropriate firmware and tracebuffer sizes.
[How]
To maintain compatibility with already released firmware where this
occurs we need to try every meta offset from 0..15 inclusive.
Extract out the meta info checker into a helper function that's called
for each of these offsets and exit early when we've found it.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During Z10, root clock gating and memory low power registers needs to
to be restored if optimization is enabled in driver.
[How]
Added new DMUB boot option for root clock gating and memory low power.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMUB binary is common for both A0 and B0. Hence, driver should
notify FW about the support for DPIA in B0.
[How]
Added dpia_supported bit in dmub_fw_boot_options and will be set
only for B0.
Assign dpia_supported to true before dm_dmub_hw_init
in B0 case.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.
[How]
1) Added inbox1 DPIA command subtype DMUB_CMD__DPIA_SET_CONFIG_ACCESS to
issue SET_CONFIG command to DMUB in dc_process_dmub_set_config_async().
DMUB processes the command with DPIA sends reply back immediately or
in an outbox1 message triggering an outbox1 interrupt to driver.
2) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
3) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for HPD & HPD RX interrupt handling for USB4 DPIA in
YELLOW_CARP_B0. USB4 DPIA HPD & HPD RX interrupts are issued from DMUB to
driver as a outbox1 message.
[HOW]
1) Created get_link_index_from_dpia_port_index() to retrieve link index
from dpia port index for HPD & HPD RX dmub notifications.
2) Added DMUB HPD & HPD RX handling in dmub_srv_stat_get_notification().
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Running into bugchecks during stress test where rptr is 0xFFFFFFFF.
Typically this is caused by a hard hang, and can come from HW outside
of DCN.
[How]
To prevent bugchecks when writing the DMUB rptr, fist check that the
rptr is valid.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.
[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're backdoor loading the DMCUB performs more work than just
the PHY reset so we can end up resetting before the cleanup has fully
finished.
[How]
Increase timeout, add udelay between spins to guarantee a minimum.
Reviewed-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise we can end up processing whatever was left in the register
if the DMCUB was previously reset.
If DMCUB gets force reset too early from another client then we might
not have even acked the disable yet - causing DMCUB instantly shutdown
if the command was 10020000.
[How]
Move the GPINT clear outside of the reset loop and do it unconditionally
after the DMCUB has been properly reset.
Reviewed-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] On S4 resume we also need to fix detection of when to reload DMCUB
firmware because we're currently using the VBIOS version which isn't
compatible with the driver version.
[How] Update the hardware init check for DCN31 since it's the ASIC that
has this issue.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jude Shih <jude.shih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dmub would notify x86 response time violation by GPINT_DATAOUT
[How]
1. Use GPINT_DATAOUT to trigger x86 interrupt
2. Register GPINT_DATAOUT interrupt handler.
3. Trigger ACR while GPINT_DATAOUT occurred.
Signed-off-by: Chun-Liang Chang <Chun-Liang.Chang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Extend existing support for DCN2.1 DMUB diagnostic logging to
DCN3.1 so we can collect useful information if the DMUB hangs.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Ability to triage DMCUB is improved with availability of certain
dmub registers not currently captured in crash dump diagnostic data.
[HOW]
Add dmub registers to diagnostic data collection.
Thanks Nicholas Kazlauskas for awesome input on this!
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
