iwlmei needs to know about the follwing events:
* Association
* De-association
* Country Code change
* SW Rfkill change
* SAR table changes
iwlmei can take the device away from us, so report the new
rfkill type when this happens.
Advertise the required data from the CSME firmware to the
usersapce: mostly, the AP that the CSME firmware is currently
associated to in case there is an active link protection
session.
Generate the HOST_ASSOC / HOST_DISSASSOC messages.
Don't support WPA1 (non-RSNA) for now.
Don't support shared wep either.
We can then determine the AUTH parameter by checking the AKM.
Feed the cipher from the key installation.
SW Rfkill will be implemented later when cfg80211 will
allow us to read the SW Rfkill state.
Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
v7: Ayala added her signed-off
remove pointless function declaration
fix a bug due to merge conflict in the HOST_ASSOC message
v8: leave a print if we have a SAP connection on a device we do
not support (yet)
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-4-emmanuel.grumbach@intel.com
The firmware can now request SMPS (due to thermal conditions), add
some code to honour such requests and bubble them up through the
stack, subject to our other SMPS constraints, e.g. from Bluetooth.
Then, if the firmware requests SMPS, then we know that it supports
a small extension to the PHY configuration API where a chain mask
of 0 means "use 1 but pick which one yourself", so in this case we
use that extension.
During firmware restart, we stay in the previous state, and the FW
will send us a notification at startup (only) if the temperature is
below the lower or above the high threshold, to sync the state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.85656b7684b9.I7a661a0758d070a750d3a91874d1a0f5fab9febc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When doing scan while 6GHz channels are not enabled, the 6GHz band
is not scanned. Thus, if there are no APs on the 2GHz and 5GHz bands
(that will allow discovery of geographic location etc. that would
allow enabling the 6GHz channels) but there are non collocated APs
on 6GHz PSC channels these would never be discovered.
To overcome this, FW added support for performing passive UHB scan
in case no APs were discovered during scan on the 2GHz and 5GHz
channels.
Add support for enabling such scan when the following conditions are
met:
- 6GHz channels are supported but not enabled by regulatory.
- Station interface is not associated or less than a defined time
interval passed from the last resume or HW reset flows.
- At least 4 channels are included in the scan request
- The scan request includes the widlcard SSID.
- At least 50 minutes passed from the last 6GHz passive scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.7c7bd00e0aeb.Ib226ad57e416b43a710c36a78a617d4243458b99@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
No need to pass the dbgfs_dir just to assign it to mvm.
Assign to mvm and then call iwl_mvm_dbgfs_register.
This is a preparation towards the addition of a delayed
op_mode_start flow.
This will allow to split the op_mode_start flow.
Registration to debugfs must happen after we register to
mac80211 and the registration to mac80211 will soon be
delayed in certain cases. In order not to have to remember
the debugfs_dir in a separate variable, just set it into
the mvm structure so that it can be usable later.
Declare mvm->debugfs_dir in the iwl_mvm structure even when
IWLWIFI_DEBUGFS isn't enabled to simplify the source code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.a92ee491863d.I047923aa3598fbf4fb6fce2cdff75a4969fedd76@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
RF Interference Mitigation is a new feature targeted to handle the
problem of interference between DDR memory and WiFi. The role of
the driver is to configure FW with the table holding a mapping
between problematic channels/bands and the corresponding frequencies.
This patch adds RFI infrastructure and adds two debugfs hooks:
- send RFI configuration command (currently with a default table) which
will reset feature in the FW
- read the table, used by the FW (which can be a subset of the table
that driver sent).
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.2cea55a09bc7.I634b79795abad499ce442631d6672ffef8fc6d41@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The argument type to iwl_mvm_notify_rx_queue() is currently just
a u8 *, but that's misleading because we actually need the inner
data to be of type struct iwl_mvm_internal_rxq_notif, because we
interpret it when we get it back from the device (to check the
sync bool and possibly the cookie.)
Therefore, clear up any potential confusion and require that the
data passed is of type struct iwl_mvm_internal_rxq_notif *.
Also, while at it, rename the "count" to "notif_size" as "count"
doesn't really clearly say what it's counting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.d28e14682bdc.I9ac366aa97db045be4daa4ba263267a3ac6a6a2f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The overcome instabilities in the RTT results add smoothing logic
to the reported results. In short, the smoothing logic tracks the
RTT average of each responder for a period of time, and in case
a new RTT results is found to be a spur, the tracked RTT average
is reported instead of the current RTT measurement.
Smooth logic debug configuration using iwl-dbg-cfg.ini:
- MVM_FTM_INITIATOR_ENABLE_SMOOTH: Set to 1 to enable smoothing logic
(default=0).
- MVM_FTM_INITIATOR_SMOOTH_ALPHA: A value between 0 - 100, defining
the weight of the current RTT results vs. the RTT average tracked
based on the previous results. A value of 100 means use only the
current RTT results.
- MVM_FTM_INITIATOR_SMOOTH_AGE_SEC: The maximal time in seconds in which
the RTT average tracked based on previous results is considered valid.
- MVM_FTM_INITIATOR_SMOOTH_UNDERSHOOT: if the current RTT is positive
and below the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
- MVM_FTM_INITIATOR_SMOOTH_OVERSHOOT: if the current RTT is positive
and above the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.48a9cec2081b.Iaec1e29f738232adfe9e2ea8e9eb9b6ff0323ae1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A FTM responder may do PASN authentication with unassociated stations
to allow secure ranging. In this case, the driver will add an internal
station and install the TK so the FW will accept protected FTM
request frames from this station and will send a protected FTM
response frame.
In addition, the driver needs to configure the HLTK to the FW so
the FW can derive the secure LTF bits. This is left for a later
patch since it is not yet supported by the FW.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.c915b44ad7dd.I72ef7f9753964555561c27ec503241105eddb14e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW changed the maximum number of scan offload profiles to 8 in new
APIs. Support it by changing the scan_offload_profile_cfg struct to be
more dynamic, so we can reuse most of the code and only change size of
the profiles array.
Change-Id: I65210cf541af46e2675a8c764d5871f7f5b070d6
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an old parameter that was used supposed to be used only when
LAR was still under development. It should not be used anymore, but,
since it's available, end-users have been mangling with it
unnecessarily. In some cases it can cause problems because when LAR
is supported the driver and the firmware do not expect it to be
disabled.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we transmit after TXQ dequeue, we aren't paying attention to
the return value of the transmit functions, leading to a potential
SKB leak.
Refactor the code a bit (and rename ..._tx to ..._tx_sta) to check
for this happening.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug - we haven't been able to check the
firmware image that was loaded for D3/not-D3 since the introduction
of the unified image...
Fix this by keeping a status flag for D3 instead of checking for
the firmware image that's loaded.
This reduces occurrences of checks for IWL_UCODE_WOWLAN to just the
code that actually loads the image or deals with it in other ways.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactored the SAR related functions from iwlmvm to acpi
in order to make it shared between different opmodes
in addition to removing unused variable ppag_rev.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
