There are a number of upcoming things in both the stack and
drivers that would otherwise conflict, so merge wireless to
wireless-next to be able to avoid those conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When CSME is connected and has link protection set, the driver must
connect to the same AP CSME is connected to.
When in link protection, modify scan request parameters to include
only the channel of the AP CSME is connected to and scan for the
same SSID. In addition, filter the scan results to include only
results from the same AP. This will make sure the driver will connect
to the same AP and will do it fast enough to keep the session alive.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.c1b55de3d704.I3895eebe18b3b672607695c887d728e113fc85ec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RADA/firmware collaborate on MIC stripping in the following
way:
- the firmware fills the IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK
value for how many words need to be removed at the end of
the frame, CRC and, if decryption was done, MIC
- if the RADA is active, it will
- remove that much from the end of the frame
- zero the value in IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK
As a consequence, the only thing the driver should need to do
is to
- unconditionally tell mac80211 that the MIC was removed
if decryption was already done
- remove as much as IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK says
at the end of the frame, since either RADA did it and then
the value is 0, or RADA was disabled and then the value is
whatever should be removed to strip both CRC & MIC
However, all this code was historically grown and getting a
bit confused. Originally, we were indicating that the MIC was
not stripped, which is the version of the code upstreamed in
commit 780e87c29e ("iwlwifi: mvm: add 9000 series RX processing")
which indicated RX_FLAG_DECRYPTED in iwl_mvm_rx_crypto().
We later had a commit to change that to also indicate that the
MIC was stripped, adding RX_FLAG_MIC_STRIPPED. However, this was
then "fixed" later to only do that conditionally on RADA being
enabled, since otherwise RADA didn't strip the MIC bytes yet.
At the time, we were also always including the FCS if the RADA
was not enabled, so that was still broken wrt. the FCS if the
RADA isn't enabled - but that's a pretty rare case. Notably
though, it does happen for management frames, where we do need
to remove the MIC and CRC but the RADA is disabled.
Later, in commit 40a0b38d7a ("iwlwifi: mvm: Fix calculation of
frame length"), we changed this again, upstream this was just a
single commit, but internally it was split into first the correct
commit and then an additional fix that reduced the number of bytes
that are removed by crypt_len. Note that this is clearly wrong
since crypt_len indicates the length of the PN header (always 8),
not the length of the MIC (8 or 16 depending on algorithm).
However, this additional fix mostly canceled the other bugs,
apart from the confusion about the size of the MIC.
To fix this correctly, remove all those additional workarounds.
We really should always indicate to mac80211 the MIC was stripped
(it cannot use it anyway if decryption was already done), and also
always actually remove it and the CRC regardless of the RADA being
enabled or not. That's simple though, the value indicated in the
metadata is zeroed by the RADA if it's enabled and used the value,
so there's no need to check if it's enabled or not.
Notably then, this fixes the MIC size confusion, letting us receive
GCMP-256 encrypted management frames correctly that would otherwise
be reported to mac80211 8 bytes too short since the RADA is turned
off for them, crypt_len is 8, but the MIC size is 16, so when we do
the adjustment based on IWL_RX_MPDU_MFLG1_MIC_CRC_LEN_MASK (which
indicates 20 bytes to remove) we remove 12 bytes but indicate then
to mac80211 the MIC is still present, so mac80211 again removes the
MIC of 16 bytes, for an overall removal of 28 rather than 20 bytes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230418122405.81345b6ab0cd.Ibe0348defb6cce11c99929a1f049e60b5cfc150c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For TM/FTM frames, report the hardware timestamps reported by the
fw as part of the RX/TX status. Since the fw reports the timestamps
in a dedicated notification (and not as part of the RX/TX status),
hold the frame until the fw timestamps notification is received.
Timestamping is enabled when a station is connected and disabled
when disconnected. For AP interface, only the first station will
have timestamping enabled since the fw only supports timestamping
for one peer.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.e0392d498101.I9bf12c8ecfb3f17253a13dc48a48647ddd6e7855@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In monitor mode, we try to report the EOF bit on the
first MPDU of an A-MPDU (hardware duplicates this bit
over all MPDUs, so it's only trustable on the first).
However, due to reshuffling in an ealier commit, the
toggle_bit != mvm->ampdu_toggle logic can no longer
work since mvm->ampdu_toggle is now set before this
code runs.
Fix this by tracking the first_subframe status in the
phy data struct and using that instead of checking.
Fixes: f1490546be ("wifi: iwlwifi: mvm: rxmq: refactor mac80211 rx_status setting")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230305124407.e273aa0d3fdc.I77db4cc247898eae8a98b80659386d6737052b95@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bunch of duplicated code in the normal data RX and
the no-data RX paths, refactor that.
Note that we're evidently not implementing the 6 GHz band in
the no-data path correctly, need to fix that in firmware
first. Also, we were setting the NSS differently, keep doing
that, but just override the previous values.
Note also that we used to drop frames with bad rate data, to
simplify that just report rate 0 and continue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20220906161827.a81580d5e769.I3ee7a1fe1adf8684c48713dbbdc2cbc60bd24cd1@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
There's currently only one driver that reports CHECKSUM_COMPLETE,
that is iwlwifi. The current hardware there calculates checksum
after the SNAP header, but only RFC 1042 (and some other cases,
but replicating the exact hardware logic for corner cases in the
driver seemed awkward.)
Newer generations of hardware will checksum _including_ the SNAP,
which makes things easier.
To handle that, simply always assume the checksum _includes_ the
SNAP header, which this patch does, requiring to first add it
for older iwlwifi hardware, and then remove it again later on
conversion.
Alternatively, we could have:
1) Always assumed the checksum starts _after_ the SNAP header;
the problem with this is that we'd have to replace the exact
"what is the SNAP" check in iwlwifi that cfg80211 has.
2) Made it configurable with some flag, but that seemed like too
much complexity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.230736e19e0e.I3e6745873585ad943c152fab9e23b5221f17a95f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we happen to decide an NSSN queue sync (IWL_MVM_RXQ_NSSN_SYNC)
for some remaining packets that are still on the queue, but just
after we've decided to do a delBA (which causes its own queues
sync with IWL_MVM_RXQ_NOTIF_DEL_BA) we can end up with a sequence
of events like this:
CPU 1 CPU 2
remove BA session with baid N
send IWL_MVM_RXQ_NOTIF_DEL_BA
send IWL_MVM_RXQ_NSSN_SYNC
get IWL_MVM_RXQ_NOTIF_DEL_BA
get IWL_MVM_RXQ_NOTIF_DEL_BA
get IWL_MVM_RXQ_NSSN_SYNC
complete IWL_MVM_RXQ_NOTIF_DEL_BA
remove N from baid_map[]
get IWL_MVM_RXQ_NSSN_SYNC
WARN_ON(!baid_map[N])
Thus, there's a race that leads in hitting the WARN_ON, but more
importantly, it's a race that potentially even results in a new
aggregation session getting assigned to baid N.
To fix this, remove the WARN_ON() in the NSSN_SYNC case, we can't
completely protect against hitting this case, so we shouldn't be
warning. However, guard ourselves against BAID reuse by doing yet
another round of queue synchronization after the entry is removed
from the baid_map, so that it cannot be reused with any in-flight
IWL_MVM_RXQ_NSSN_SYNC messages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083237.44abbbc50f40.I5492600dfe513356555abe2d7df0e2835846e3d8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
