Mandatory WFA testcase
CT_Security_WPA2Personal_STA_RSNEBoundsVerification-AbsentRSNCap,
performs bounds verfication on Beacon and/or Probe response frames. It
failed and observed the reason to be absence of cipher suite and AKM
suite in RSN information. To fix this, enable the RSN flag before extracting RSN
capabilities.
Fixes: cd21d99e59 ("wifi: wilc1000: validate pairwise and authentication suite offsets")
Signed-off-by: Amisha Patel <amisha.patel@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230421181005.4865-1-amisha.patel@microchip.com
Due to the two cherry picked commits from wireless to wireless-next we have
several conflicts in mt76. To avoid any bugs with conflicts merge wireless into
wireless-next.
96f134dc19 wifi: mt76: handle possible mt76_rx_token_consume failures
fe13dad899 wifi: mt76: dma: do not increment queue head if mt76_dma_add_buf fails
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fault injection test reports this issue:
kernel BUG at net/core/dev.c:10731!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
Call Trace:
<TASK>
wilc_netdev_ifc_init+0x19f/0x220 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5]
wilc_cfg80211_init+0x30c/0x380 [wilc1000 884bf126e9e98af6a708f266a8dffd53f99e4bf5]
wilc_bus_probe+0xad/0x2b0 [wilc1000_spi 1520a7539b6589cc6cde2ae826a523a33f8bacff]
spi_probe+0xe4/0x140
really_probe+0x17e/0x3f0
__driver_probe_device+0xe3/0x170
driver_probe_device+0x49/0x120
The root case here is alloc_ordered_workqueue() fails, but
cfg80211_unregister_netdevice() or unregister_netdev() not be called in
error handling path. To fix add unregister_netdev goto lable to add the
unregister operation in error handling path.
Fixes: 09ed8bfc52 ("wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1669289902-23639-1-git-send-email-wangyufen@huawei.com
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for various key operations on MLD by adding new parameter
link_id. Pass the link_id received from userspace to driver for add_key,
get_key, del_key, set_default_key, set_default_mgmt_key and
set_default_beacon_key to support configuring keys specific to each MLO
link. Userspace must not specify link ID for MLO pairwise key since it
is common for all the MLO links.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20220730052643.1959111-4-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the link_station_parameters structure in the station_parameters
structure (and remove the station_parameters fields already existing
in link_station_parameters).
Now, for an MLD station, the default link is added together with
the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For power-up sequence, WILC expects RESET set to high 5ms after making
chip_en(enable) so corrected chip power-up sequence by making RESET high.
For Power-Down sequence, the correct sequence make RESET and CHIP_EN low
without any extra delay.
Fixes: ec031ac479 ("wilc1000: Add reset/enable GPIO support to SPI driver")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220524120606.9675-1-ajay.kathat@microchip.com
'vmm_table' array contains the size of data buffer length including host
header length. In 'vmm_table' array, the Zero value means the end of
vmm_entries that needs to transfer to firmware which is calculated based on
VMM free size in firmware.
Use 'vmm_table' valid entry check before fetching the entry from TX queue to
only copy valid number of entries to avoid possible NULL pointer exception
observed sometimes during large file transfers.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-5-ajay.kathat@microchip.com
Monitor(mon.) interface is used for handling the AP mode and 'ieee80211_ptr'
reference is not getting set for it. Like earlier implementation,
use register_netdevice() instead of cfg80211_register_netdevice() which
expects valid 'ieee80211_ptr' reference to avoid the possible crash.
Fixes: 2fe8ef1062 ("cfg80211: change netdev registration/unregistration semantics")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220504161924.2146601-3-ajay.kathat@microchip.com
Mark Brown says:
====================
spi: Make remove() return void
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
====================
Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the SDIO driver, the RESET/ENABLE pins of WILC1000 are controlled
through the SDIO power sequence driver. This commit adds analogous
support for the SPI driver. Specifically, during initialization, the
chip will be ENABLEd and taken out of RESET and during
deinitialization, the chip will be placed back into RESET and disabled
(both to reduce power consumption and to ensure the WiFi radio is
off).
Both RESET and ENABLE GPIOs are optional. However, if the ENABLE GPIO
is specified, then the RESET GPIO should normally also be specified as
otherwise there is no way to ensure proper timing of the ENABLE/RESET
sequence.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-2-davidm@egauge.net
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3b ("wilc1000: use goto labels on error path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
The wakeup and sleep commands need to be sent to the WILC chip only
when it is in power save mode (PSM, as controlled by "iw dev wlan0 set
power_save on/off"). The commands are relatively costly, so it pays
to skip them when possible.
iperf3 without this patch (no significant different with PSM on/off):
TX 0.00-120.01 sec 140 MBytes 9.82 Mbits/sec
RX 0.00-120.69 sec 283 MBytes 19.6 Mbits/sec
with this patch applied:
PSM off (TX is 46% improved, RX slightly improved; may not be significant):
TX 0.00-120.00 sec 206 MBytes 14.4 Mbits/sec
RX 0.00-120.48 sec 322 MBytes 22.4 Mbits/sec
PSM on (no significant change):
TX 0.00-120.00 sec 140 MBytes 9.78 Mbits/sec
RX 0.00-120.08 sec 257 MBytes 18.0 Mbits/sec
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211210203016.3680425-2-davidm@egauge.net
This follows normal Linux convention and is more useful since the new
name will make it apparent which network device the work-queue is for
(e.g., the name will be "wlan0-wq" for network device "wlan0").
hif_workqueue allocation has to move from
cfg80211.c:wilc_cfg80211_init() to netdev.c:wilc_netdev_ifc_init()
because the network device name is not known until after the netdev is
registered. The move also makes sense because netdev.c is already
responsible for destroying the work queue when it is no longer needed.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211209044411.3482259-5-davidm@egauge.net
