Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
Pull Kbuild updates from Masahiro Yamada:
- Avoid 'constexpr', which is a keyword in C23
- Allow 'dtbs_check' and 'dt_compatible_check' run independently of
'dt_binding_check'
- Fix weak references to avoid GOT entries in position-independent code
generation
- Convert the last use of 'optional' property in arch/sh/Kconfig
- Remove support for the 'optional' property in Kconfig
- Remove support for Clang's ThinLTO caching, which does not work with
the .incbin directive
- Change the semantics of $(src) so it always points to the source
directory, which fixes Makefile inconsistencies between upstream and
downstream
- Fix 'make tar-pkg' for RISC-V to produce a consistent package
- Provide reasonable default coverage for objtool, sanitizers, and
profilers
- Remove redundant OBJECT_FILES_NON_STANDARD, KASAN_SANITIZE, etc.
- Remove the last use of tristate choice in drivers/rapidio/Kconfig
- Various cleanups and fixes in Kconfig
* tag 'kbuild-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (46 commits)
kconfig: use sym_get_choice_menu() in sym_check_prop()
rapidio: remove choice for enumeration
kconfig: lxdialog: remove initialization with A_NORMAL
kconfig: m/nconf: merge two item_add_str() calls
kconfig: m/nconf: remove dead code to display value of bool choice
kconfig: m/nconf: remove dead code to display children of choice members
kconfig: gconf: show checkbox for choice correctly
kbuild: use GCOV_PROFILE and KCSAN_SANITIZE in scripts/Makefile.modfinal
Makefile: remove redundant tool coverage variables
kbuild: provide reasonable defaults for tool coverage
modules: Drop the .export_symbol section from the final modules
kconfig: use menu_list_for_each_sym() in sym_check_choice_deps()
kconfig: use sym_get_choice_menu() in conf_write_defconfig()
kconfig: add sym_get_choice_menu() helper
kconfig: turn defaults and additional prompt for choice members into error
kconfig: turn missing prompt for choice members into error
kconfig: turn conf_choice() into void function
kconfig: use linked list in sym_set_changed()
kconfig: gconf: use MENU_CHANGED instead of SYMBOL_CHANGED
kconfig: gconf: remove debug code
...
Kbuild conventionally uses $(obj)/ for generated files, and $(src)/ for
checked-in source files. It is merely a convention without any functional
difference. In fact, $(obj) and $(src) are exactly the same, as defined
in scripts/Makefile.build:
src := $(obj)
When the kernel is built in a separate output directory, $(src) does
not accurately reflect the source directory location. While Kbuild
resolves this discrepancy by specifying VPATH=$(srctree) to search for
source files, it does not cover all cases. For example, when adding a
header search path for local headers, -I$(srctree)/$(src) is typically
passed to the compiler.
This introduces inconsistency between upstream and downstream Makefiles
because $(src) is used instead of $(srctree)/$(src) for the latter.
To address this inconsistency, this commit changes the semantics of
$(src) so that it always points to the directory in the source tree.
Going forward, the variables used in Makefiles will have the following
meanings:
$(obj) - directory in the object tree
$(src) - directory in the source tree (changed by this commit)
$(objtree) - the top of the kernel object tree
$(srctree) - the top of the kernel source tree
Consequently, $(srctree)/$(src) in upstream Makefiles need to be replaced
with $(src).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
le32p_replace_bits() only updates partial bits of rate_mask, and GCC warns
below. Set initial value to avoid warnings, and prevent random value of
missed bits (bit 6 of rate_mask.macid_and_short_gi).
In file included from ./include/linux/fortify-string.h:5,
from ./include/linux/string.h:369,
from ./include/linux/bitmap.h:13,
from ./include/linux/cpumask.h:13,
from ./include/linux/sched.h:16,
from drivers/net/wireless/realtek/rtlwifi/rtl8192d/../wifi.h:9,
from drivers/net/wireless/realtek/rtlwifi/rtl8192d/hw_common.c:4:
In function 'le32p_replace_bits',
inlined from 'rtl92de_update_hal_rate_mask.isra' at drivers/net/wireless/realtek/rtlwifi/rtl8192d/hw_common.c:986:2:
./include/linux/bitfield.h:189:15: warning: 'rate_mask' is used uninitialized [-Wuninitialized]
189 | *p = (*p & ~to(field)) | type##_encode_bits(val, field); \
| ^~
./include/linux/bitfield.h:196:9: note: in expansion of macro '____MAKE_OP'
196 | ____MAKE_OP(le##size,u##size,cpu_to_le##size,le##size##_to_cpu) \
| ^~~~~~~~~~~
./include/linux/bitfield.h:201:1: note: in expansion of macro '__MAKE_OP'
201 | __MAKE_OP(32)
| ^~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/rtl8192d/hw_common.c: In function 'rtl92de_update_hal_rate_mask.isra':
drivers/net/wireless/realtek/rtlwifi/rtl8192d/hw_common.c:863:37: note: 'rate_mask' declared here
863 | struct rtl92d_rate_mask_h2c rate_mask;
| ^~~~~~~~~
Compile tested only.
Fixes: 014bba73b5 ("wifi: rtlwifi: Adjust rtl8192d-common for USB")
Cc: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240504111916.31445-1-pkshih@realtek.com
Wflex-array-member-not-at-end is coming in GCC-14, and we are getting
ready to enable it globally.
So, remove unused structs and fix the following
-Wflex-array-member-not-at-end warnings:
drivers/net/wireless/realtek/rtlwifi/btcoexist/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8192c/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8192ce/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8192de/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8192se/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8723be/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8723com/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
drivers/net/wireless/realtek/rtlwifi/wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/ZjLFIa31BGPVCGh1@neat
Once we connect to AP with 802.11w enabled, IGTK rekey happen during GTK
happen. We get IGTK IPN from mac80211 and set to firmware, and get latest
IGTK IPN from AOAC report then update to mac80211 after resume. When rekey
happen, also update new IGTK key info to mac80211. Furthermore, We
construct SA query reply packet to firmware. If firmware received SA query
request from AP can transmit reply back when suspend.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240502022505.28966-11-pkshih@realtek.com
When resume we parse AOAC report from firmware using H2C and C2H
registers before enable interrupt, then update PTK RX PN and GTK RX PN.
After enable interrupt, we parse AOAC report using H2C and C2H commands,
then update PTK TX PN and update new GTK key info if GTK rekey during
suspend. Furthermore, We update pattern match index if wakeup by pattern.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240502022505.28966-10-pkshih@realtek.com
We construct EAPoL packet with various encryption method, and download
to firmware. Also we add Key Encryption Key (KEK) and Key Confirmation Key
(KCK) to H2C command. Once firmware received EAPoL group rekey packet(1/2)
can TX EAPoL group rekey packet(2/2) when suspend.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240502022505.28966-8-pkshih@realtek.com
After enabling packet offload, the TX will be stuck after resume from
WoWLAN mode. And the 8852c gets error messages like
rtw89_8852ce 0000:04:00.0: No busy txwd pages available
rtw89_8852ce 0000:04:00.0: queue 0 txwd 100 is not idle
rtw89_8852ce 0000:04:00.0: queue 0 txwd 101 is not idle
rtw89_8852ce 0000:04:00.0: queue 0 txwd 102 is not idle
rtw89_8852ce 0000:04:00.0: queue 0 txwd 103 is not idle
If suspend/resume many times that firmware will download failed and
disconnection.
To fix these issues, We removed the rtw89_hci_disable_intr() and
rtw89_hci_enable_intr() during rtw89_wow_swap_fw() to prevent add packet
offload can't receive c2h back due to interrupt disable. Only 8852C and
8922A needs to disable interrupt before downloading fw.
Furthermore, we avoid using low power HCI mode on WoWLAN mode, to prevent
interrupt enabled, then get interrupt and calculate RXBD mismatched due to
software RXBD index already reset but hardware RXBD index not yet.
Fixes: 5c12bb66b7 ("wifi: rtw89: refine packet offload flow")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240502022505.28966-3-pkshih@realtek.com
Remove unnecessary includes from driver. The first step is to add
necessary includes to driver's header files to make them can be included
individually. Then, driver's C files include driver's header files first,
and check if still missed header files of kernel.
The results show that most C files only include driver's header files.
Only core.c needs to include additional linux/firmware.h.
Also sort includes in alphabetic order.
Compile tested only.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240429024711.30992-1-pkshih@realtek.com
The driver is already in a directory named rtl8xxxu, there's no need to
duplicate that in the filename as well. Now file listing looks a lot more
reasonable:
8188e.c 8192c.c 8192f.c 8723a.c core.c Makefile rtl8xxxu.h
8188f.c 8192e.c 8710b.c 8723b.c Kconfig regs.h
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426141939.3881678-2-kvalo@kernel.org
I noticed by random that rtl8xxxu includes linux/wireless.h even though it
doesn't need it. While investigating a bit more I found even more unused
include files:
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ethtool.h>
It looks like that the includes are just copied to every file without checking
if the file really needs the include. So more includes could be removed but
that would need more careful analysis per each file.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426141939.3881678-1-kvalo@kernel.org
Power sequence is a flow to enable/disable WiFi card with hardware
parameters. Adjust power and clock parameters according to results
of internal simulation and verification, so apply them to have better
power consumption.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240426061200.44262-2-pkshih@realtek.com
Improve readability:
* add empty lines
* use abs_diff in rtl92d_dm_txpower_tracking_callback_thermalmeter
* roll up repeated statements into a for loop in
rtl92d_dm_txpower_tracking_callback_thermalmeter
* shorten lines by replacing many instances of "rtlpriv->dm" with "dm"
pointer in rtl92d_dm_txpower_tracking_callback_thermalmeter
* sort some declarations by length
* refactor _rtl92d_get_txpower_writeval_by_regulatory a little
* refactor _rtl92de_readpowervalue_fromprom a little
Delete unused structs tag_dynamic_init_gain_operation_type_definition
and swat.
Simplify rtl92d_fill_h2c_cmd a little and delete a pointless wrapper
function.
Tested with a single MAC single PHY USB dongle from Aliexpress labelled
"CC&C WL-6210-V3".
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/f6acfa78-2f4e-47f1-95d4-65aa77510113@gmail.com
Create the new module rtl8192d-common and move some code into it from
rtl8192de. Now the rtl8192de driver (PCI) and the new rtl8192du driver
(USB) can share some of the code.
This is mostly the code that required little effort to make it
shareable. There are a few more functions which they could share, with
more changes.
Add phy_iq_calibrate member to struct rtl_hal_ops to allow moving the
TX power tracking code from dm.c.
The other changes in this patch are adjusting whitespace, renaming some
functions, making some arrays const, and making checkpatch.pl less
unhappy.
rtl8192de is compile-tested only. rtl8192d-common is tested with the
new rtl8192du driver.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/69c4358a-6fbf-4433-92a6-341c83e9dd48@gmail.com
Structs rx_desc_92d and rx_fwinfo_92d will not work for big endian
systems.
Delete rx_desc_92d because it's big and barely used, and instead use
the get_rx_desc_rxmcs and get_rx_desc_rxht functions, which work on big
endian systems too.
Fix rx_fwinfo_92d by duplicating four of its members in the correct
order.
Tested only with RTL8192DU, which will use the same code.
Tested only on a little endian system.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/698463da-5ef1-40c7-b744-fa51ad847caf@gmail.com
Some (all?) management frames are incorrectly reported to mac80211 as
decrypted when actually the hardware did not decrypt them. This results
in speeds 3-5 times lower than expected, 20-30 Mbps instead of 100
Mbps.
Fix this by checking the encryption type field of the RX descriptor.
rtw88 does the same thing.
This fix was tested only with rtl8192du, which will use the same code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/4d600435-f0ea-46b0-bdb4-e60f173da8dd@gmail.com
Different channels have different TX power settings. rtl8192de is using
the TX power setting from the wrong channel in the 5 GHz band because
_rtl92c_phy_get_rightchnlplace expects an array which includes all the
channel numbers, but it's using an array which includes only the 5 GHz
channel numbers.
Use the array channel_all (defined in rtl8192de/phy.c) instead of
the incorrect channel5g (defined in core.c).
Tested only with rtl8192du, which will use the same TX power code.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/c7653517-cf88-4f57-b79a-8edb0a8b32f0@gmail.com
This function is to let Bluetooth know Wi-Fi is using which channel,
and ask Bluetooth do not hop into the nearby channel. Wi-Fi channel
is saved at role info, this patch make the logic also get the channel
value from version 8 role info.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240423130502.32682-7-pkshih@realtek.com
The feature can help to know how the firmware mechanism working.
There are several trigger point set in firmware. If driver send
the H2C command to firmware to enable the trigger, firmware will
toggle GPIO to perform the firmware mechanism.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-8-pkshih@realtek.com
When the PTA breaks Wi-Fi traffic request caused Bluetooth traffic,
it means Bluetooth polluted the Wi-Fi traffic. When Wi-Fi is TX, the
mechanism can ignore the polluted Wi-Fi packet retry counter, it is
help to the stability of Wi-Fi TX rate. The chip RTL8922A has not only
one MAC, so need to include the all MAC as reference.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-6-pkshih@realtek.com
PTA(packet traffic arbitration) is a coexistence hardware feature.
Wi-Fi & Bluetooth owns their PTA, the function is to show whose PTA
control the traffic now. RTL8922A PTA control is controlled by hardware
logic, there is no register to monitor the setting.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240418021207.32173-5-pkshih@realtek.com
