[ Upstream commit f1de58802f ]
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09c24094b2 ]
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fcb461e2bc upstream.
There is an issue that when PCIe switch is connected to an Armada 3700
board, there will be lots of warnings about PIO errors when reading the
config space. According to Aardvark PIO read and write sequence in HW
specification, the current way to check PIO status has the following
issues:
1) For PIO read operation, it reports the error message, which should be
avoided according to HW specification.
2) For PIO read and write operations, it only checks PIO operation complete
status, which is not enough, and error status should also be checked.
This patch aligns the code with Aardvark PIO read and write sequence in HW
specification on PIO status check and fix the warnings when reading config
space.
[pali: Fix CRS handling when CRSSVE is not enabled]
Link: https://lore.kernel.org/r/20210722144041.12661-2-pali@kernel.org
Tested-by: Victor Gu <xigu@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # b1bd571447 ("PCI: aardvark: Indicate error in 'val' when config read fails")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64f160e19e upstream.
In commit 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window configuration")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f67092eff2 ]
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf5f7ab23 ]
An IRQ handler may be called at any time after it is registered, so
anything it relies on must be ready before registration.
rockchip_pcie_subsys_irq_handler() and rockchip_pcie_client_irq_handler()
read registers in the PCIe controller, but we registered them before
turning on clocks to the controller. If either is called before the clocks
are turned on, the register reads fail and the machine hangs.
Similarly, rockchip_pcie_legacy_int_handler() uses rockchip->irq_domain,
but we installed it before initializing irq_domain.
Register IRQ handlers after their data structures are initialized and
clocks are enabled.
Found by enabling CONFIG_DEBUG_SHIRQ, which calls the IRQ handler when it
is being unregistered. An error during the probe path might cause this
unregistration and IRQ handler execution before the device or data
structure init has finished.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210608080409.1729276-1-javierm@redhat.com
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94d2276320 ]
On removing the device, any work item (hv_pci_devices_present() or
hv_pci_eject_device()) scheduled on workqueue hbus->wq may still be running
and race with hv_pci_remove().
This can happen because the host may send PCI_EJECT or PCI_BUS_RELATIONS(2)
and decide to rescind the channel immediately after that.
Fix this by flushing/destroying the workqueue of hbus before doing hbus remove.
Link: https://lore.kernel.org/r/1620806800-30983-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7f71a409fe upstream.
Marvell Armada 3700 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in aardvark driver for both PCI vendor id and PCI
subsystem vendor id.
This change affects and fixes PCI vendor id of emulated PCIe root bridge.
After this change emulated PCIe root bridge has correct vendor id.
Link: https://lore.kernel.org/r/20210624222621.4776-5-pali@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f18139966d upstream.
Trying to start a new PIO transfer by writing value 0 in PIO_START register
when previous transfer has not yet completed (which is indicated by value 1
in PIO_START) causes an External Abort on CPU, which results in kernel
panic:
SError Interrupt on CPU0, code 0xbf000002 -- SError
Kernel panic - not syncing: Asynchronous SError Interrupt
To prevent kernel panic, it is required to reject a new PIO transfer when
previous one has not finished yet.
If previous PIO transfer is not finished yet, the kernel may issue a new
PIO request only if the previous PIO transfer timed out.
In the past the root cause of this issue was incorrectly identified (as it
often happens during link retraining or after link down event) and special
hack was implemented in Trusted Firmware to catch all SError events in EL3,
to ignore errors with code 0xbf000002 and not forwarding any other errors
to kernel and instead throw panic from EL3 Trusted Firmware handler.
Links to discussion and patches about this issue:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
But the real cause was the fact that during link retraining or after link
down event the PIO transfer may take longer time, up to the 1.44s until it
times out. This increased probability that a new PIO transfer would be
issued by kernel while previous one has not finished yet.
After applying this change into the kernel, it is possible to revert the
mentioned TF-A hack and SError events do not have to be caught in TF-A EL3.
Link: https://lore.kernel.org/r/20210608203655.31228-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da81 ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16f7ae5906 ]
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
Fix them with the obvious one-line changes.
Link: https://lore.kernel.org/r/20210308152501.2135937-2-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3d0b2a3a87 upstream.
Both TI's AM65x (K3) and TI's K2 PCIe driver are implemented in
pci-keystone. However Only K2 PCIe driver should use it's own pci_ops
for configuration space accesses. But commit 10a797c6e5
("PCI: dwc: keystone: Use pci_ops for config space accessors") used
custom pci_ops for both AM65x and K2. This breaks configuration space
access for AM65x platform. Fix it here.
Link: https://lore.kernel.org/r/20210317131518.11040-1-kishon@ti.com
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: <stable@vger.kernel.org> # v5.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42814c438a ]
The for_each_available_child_of_node helper internally makes use of the
of_get_next_available_child() which performs an of_node_get() on each
iteration when searching for next available child node.
Should an available child node be found, then it would return a device
node pointer with reference count incremented, thus early return from
the middle of the loop requires an explicit of_node_put() to prevent
reference count leak.
To stop the reference leak, explicitly call of_node_put() before
returning after an error occurred.
Link: https://lore.kernel.org/r/20210120184810.3068794-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a93c00e5f9 ]
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained IRQ
handler").
Based on the mail discussion, it seems ok to drop the error handling.
Link: https://lore.kernel.org/r/20210115212435.19940-3-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58adbfb3eb ]
The Rockchip PCIe controller DT binding clearly states that 'ep-gpios' is
an optional property. And indeed there are boards that don't require it.
Make the driver follow the binding by using devm_gpiod_get_optional()
instead of devm_gpiod_get().
[bhelgaas: tidy whitespace]
Link: https://lore.kernel.org/r/20210121162321.4538-2-wens@kernel.org
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Fixes: 956cd99b35 ("PCI: rockchip: Separate common code from RC driver")
Fixes: 964bac9455 ("PCI: rockchip: Split out rockchip_pcie_parse_dt() to parse DT")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1002573ee3 ]
Function cdns_pcie_host_map_dma_ranges() iterates over a PCIe host bridge
DMA ranges using the resource_list_for_each_entry() iterator, returning an
error if cdns_pcie_host_bar_config() fails.
49e427e6bd ("Merge branch 'pci/host-probe-refactor'") botched a merge so
it *always* returned after the first DMA range, even if no error occurred.
Fix the error checking so we return early only when an error occurs.
[bhelgaas: commit log]
Fixes: 49e427e6bd ("Merge branch 'pci/host-probe-refactor'")
Link: https://lore.kernel.org/r/20210216205935.3112661-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89bbcaac3d ]
Second stage bootloaders prior to Linux boot may use all inbound windows
including IARR1/IMAP1. We need to ensure that all previous configuration
of inbound windows are invalidated during the initialization stage of
the Linux iProc PCIe driver so let's add a fix to define and invalidate
IARR1/IMAP1 because it is currently missing, fixing the issue.
Link: https://lore.kernel.org/r/20201001060054.6616-3-srinath.mannam@broadcom.com
Fixes: 9415743e4c ("PCI: iproc: Invalidate PAXB address mapping")
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Prior to commit 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources"),
the DWC driver was setting up the last memory resource rather than the
first memory resource. This doesn't matter for most platforms which only
have 1 memory resource, but it broke Tegra194 which has a 2nd
(prefetchable) memory region that requires an ATU entry. The first region
on Tegra194 relies on the default 1:1 pass-thru of outbound transactions
and doesn't need an ATU entry.
Fixes: 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/r/20201026154852.221483-1-robh@kernel.org
Reported-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
- Drop return value checking for debugfs_create() calls (Greg
Kroah-Hartman)
- Convert debugfs "ports" file to use DEFINE_SEQ_ATTRIBUTE() (Liu Shixin)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Convert to use DEFINE_SEQ_ATTRIBUTE macro
PCI: tegra: No need to check return value of debugfs_create() functions
- Document R8A774A1, R8A774B1, R8A774E1 endpoint support in DT (Lad
Prabhakar)
- Add R8A774A1, R8A774B1, R8A774E1 (RZ/G2M, RZ/G2N, RZ/G2H) IDs to endpoint
test (Lad Prabhakar)
- Add device tree support for R8A7742 (Lad Prabhakar)
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva)
* remotes/lorenzo/pci/rcar:
dt-bindings: PCI: rcar: Add device tree support for r8a7742
PCI: rcar-gen2: Use fallthrough pseudo-keyword
misc: pci_endpoint_test: Add Device ID for RZ/G2H PCIe controller
dt-bindings: pci: rcar-pci-ep: Document r8a774e1
misc: pci_endpoint_test: Add Device ID for RZ/G2M and RZ/G2N PCIe controllers
dt-bindings: pci: rcar-pci-ep: Document r8a774a1 and r8a774b1
