[ Upstream commit 7a6a723e98 ]
There is no point in calling 'free_irq()' explicitly for
'WCD9335_IRQ_SLIMBUS' in the remove function.
The irqs are requested in 'wcd9335_setup_irqs()' using a resource managed
function (i.e. 'devm_request_threaded_irq()').
'wcd9335_setup_irqs()' requests all what is defined in the 'wcd9335_irqs'
structure.
This structure has only one entry for 'WCD9335_IRQ_SLIMBUS'.
So 'devm_request...irq()' + explicit 'free_irq()' would lead to a double
free.
Remove the unneeded 'free_irq()' from the remove function.
Fixes: 20aedafdf4 ("ASoC: wcd9335: add support to wcd9335 codec")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Message-Id: <0614d63bc00edd7e81dd367504128f3d84f72efa.1629091028.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b374b649 ]
Module configuration may differ between its instances depending on
resources required and input and output audio format. Available
parameters to select from are stored in module resource and interface
(format) lists. These come from topology, together with description of
each of pipe's modules.
Ignoring index value provided by topology and relying always on 0th
entry leads to unexpected module behavior due to under/overbudged
resources assigned or impropper format selection. Fix by taking entry at
index specified by topology.
Fixes: f6fa56e225 ("ASoC: Intel: Skylake: Parse and update module config structure")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihalf.com>
Link: https://lore.kernel.org/r/20210818075742.1515155-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 772d44526e ]
When I booted up on a board that had a slightly different codec
stuffed on it, I got this message at bootup:
rt5682 9-001a: Device with ID register 6749 is not rt5682
That's normal/expected, but what wasn't normal was the splat that I
got after:
WARNING: CPU: 7 PID: 176 at drivers/regulator/core.c:2151 _regulator_put+0x150/0x158
pc : _regulator_put+0x150/0x158
...
Call trace:
_regulator_put+0x150/0x158
regulator_bulk_free+0x48/0x70
devm_regulator_bulk_release+0x20/0x2c
release_nodes+0x1cc/0x244
devres_release_all+0x44/0x60
really_probe+0x17c/0x378
...
This is because the error paths don't turn off the regulator. Let's
fix that.
Fixes: 0ddce71c21 ("ASoC: rt5682: add rt5682 codec driver")
Fixes: 87b42abae9 ("ASoC: rt5682: Implement remove callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210811081751.v2.1.I4a1d9aa5d99e05aeee15c2768db600158d76cab8@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4eeaed04e ]
Sparse warnings triggered truncating the IDs of some platform device
tables. Unfortunately some of the IDs in the match tables were missed
which breaks audio. The KBL change has been verified to fix audio, the
CML change was not tested as it was found through grepping the broken
changes and found to match the same situation in anticipation that it
should also be fixed.
Fixes: 94efd726b9 ("ASoC: Intel: kbl_da7219_max98357a: shrink platform_id below 20 characters")
Fixes: 24e46fb811 ("ASoC: Intel: bxt_da7219_max98357a: shrink platform_id below 20 characters")
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Tested-by: Matt Davis <mattedavis@google.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210809213544.1682444-1-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 13d9c6b998 upstream.
ASUS ROG Strix G17 has the very same PCI and codec SSID (1043:103f) as
ASUS TX300, and unfortunately, the existing quirk for TX300 is broken
on ASUS ROG. Actually the device works without the quirk, so we'll
need to clear the quirk before applying for this device.
Since ASUS ROG has a different codec (ALC294 - while TX300 has
ALC282), this patch adds a workaround for the device, just clearing
the codec->fixup_id by checking the codec vendor_id.
It's a bit ugly to add such a workaround there, but it seems to be the
simplest way.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214101
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210820143214.3654-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31428c7874 ]
When the component level pin control functions were added they for some
no longer obvious reason handled adding prefixing of widget names. This
meant that when the lack of prefix handling in the DAPM level pin
operations was fixed by ae4fc53224 (ASoC: dapm: use component
prefix when checking widget names) the one device using the component
level API ended up with the prefix being applied twice, causing all
lookups to fail.
Fix this by removing the redundant prefixing from the component code,
which has the nice side effect of also making that code much simpler.
Reported-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210726194123.54585-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65ca89c2b1 ]
The commit 2e6b836312 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
Fixes: 2e6b836312 ("ASoC: intel: atom: Fix reference to PCM buffer address")
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/2048c6aa-2187-46bd-6772-36a4fb3c5aeb@redhat.com
Link: https://lore.kernel.org/r/20210819152945.8510-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b353bbeae ]
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2c39ca6885 upstream.
The tlv320aic31xx driver relies on regcache_sync() to restore the register
contents after going to _BIAS_OFF, for example during system suspend. This
does not work for the jack detection configuration since that is configured
via the same register that status is read back from so the register is
volatile and not cached. This can also cause issues during init if the jack
detection ends up getting set up before the CODEC is initially brought out
of _BIAS_OFF, we will reset the CODEC and resync the cache as part of that
process.
Fix this by explicitly reapplying the jack detection configuration after
resyncing the register cache during power on.
This issue was found by an engineer working off-list on a product
kernel, I just wrote up the upstream fix.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210723180200.25105-1-broonie@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 827f3164aa upstream.
Along with the transition to the managed PCM buffers, the driver now
accepts the dynamically allocated buffer, while it still kept the
reference to the old preallocated buffer address. This patch corrects
to the right reference via runtime->dma_addr.
(Although this might have been already buggy before the cleanup with
the managed buffer, let's put Fixes tag to point that; it's a corner
case, after all.)
Fixes: d55894bc27 ("ASoC: uniphier: Use managed buffer allocation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210728112353.6675-5-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc0dc8a73e upstream.
The recent fix c4824ae7db ("ALSA: pcm: Fix mmap capability check")
restricts the mmap capability only to the drivers that properly set up
the buffers, but it caused a regression for a few drivers that manage
the buffer on its own way.
For those with UNKNOWN buffer type (i.e. the uninitialized / unused
substream->dma_buffer), just assume that the driver handles the mmap
properly and blindly trust the hardware info bit.
Fixes: c4824ae7db ("ALSA: pcm: Fix mmap capability check")
Reported-and-tested-by: Jeff Woods <jwoods@fnordco.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5him0gpghv.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66291b6adb upstream.
The change to restore the autosuspend from the disabled state uses a
wrong check: namely, it should have been the exact comparison of the
quirk_type instead of the bitwise and (&). Otherwise it matches
wrongly with the other quirk types.
Although re-enabling the autosuspend for the already enabled device
shouldn't matter much, it's better to fix the unbalanced call.
Fixes: 9799110825 ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5hr1flh9ov.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4511781f95 ]
The following scenario describes an echo test for
Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051).
We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode.
In clock find source function, we get value 0x2 for clock selector
and 0x1 for clock source.
Kernel-4.14 behavior
Since clock source is valid so clock selector was not set again.
We pass through this function and start a playback stream(USB OUT transfer)
in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector
and 0x1 for clock source. Finally clock id with this setting is 0x9.
Kernel-5.10 behavior
Clock selector was always set one more time even it is valid.
When we start a playback stream, we will get 0x2 for clock selector
and 0x1 for clock source. In this case clock id becomes 0xA.
This is an incorrect clock source setting and results in severe noises.
We see wrong data rate in USB IN transfer.
(From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms.
This earphone works fine on older kernel version load because
this is a newly-added behavior.
Fixes: d2e8f64125 ("ALSA: usb-audio: Explicitly set up the clock selector")
Signed-off-by: chihhao.chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97367c9722 upstream.
It turned out that the current implementation of the port subscription
is racy. The subscription contains two linked lists, and we have to
add to or delete from both lists. Since both connection and
disconnection procedures perform the same order for those two lists
(i.e. src list, then dest list), when a deletion happens during a
connection procedure, the src list may be deleted before the dest list
addition completes, and this may lead to a use-after-free or an Oops,
even though the access to both lists are protected via mutex.
The simple workaround for this race is to change the access order for
the disconnection, namely, dest list, then src list. This assures
that the connection has been established when disconnecting, and also
the concurrent deletion can be avoided.
Reported-and-tested-by: folkert <folkert@vanheusden.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210801182754.GP890690@belle.intranet.vanheusden.com
Link: https://lore.kernel.org/r/20210803114312.2536-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
