Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Fixes: 998f70d180 ("mfd: Add base driver for qnap-mcu devices")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250310031145.650950-1-nichen@iscas.ac.cn
Signed-off-by: Lee Jones <lee@kernel.org>
Utilise devm_*() managed resource helpers for freeing IRQs instead.
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Lee Jones <lee@kernel.org>
The chipid macro/variable and regmap_read function call is not needed
because the TPS65219_REG_TI_DEV_ID register value is not a consistent value
across TPS65219 PMIC config versions. Reading from the DEV_ID register
without a consistent value to compare it to isn't useful. There isn't a
way to verify the match data ID is the same ID read from the DEV_ID device
register. 0xF0 isn't a DEV_ID value consistent across TPS65219 NVM
configurations.
For TPS65215, there is a consistent value in bits 5-0 of the DEV_ID
register. However, there are other error checks in place within probe()
that apply to both PMICs rather than keeping this isolated check for one
PMIC.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://lore.kernel.org/r/20250206173725.386720-4-s-ramamoorthy@ti.com
Signed-off-by: Lee Jones <lee@kernel.org>
If offset end up being high enough, right hand expression in functions
like sm501_gpio_set() shifted left for that number of bits, may
not fit in int type.
Just in case, fix that by using BIT() both as an option safe from
overflow issues and to make this step look similar to other gpio
drivers.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: f61be273d3 ("sm501: add gpiolib support")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20250115171206.20308-1-n.zhandarovich@fintech.ru
Signed-off-by: Lee Jones <lee@kernel.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114192538.911970-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for STM32MP25 SoC. Use newly introduced compatible, to handle
new features.
Identification and hardware configuration registers allow to read the
timer version and capabilities (counter width, number of channels...).
So, rework the probe to avoid touching ARR register by simply read the
counter width when available. This may avoid messing with a possibly
running timer.
Also add useful bit fields to stm32-timers header file.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250110091922.980627-3-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
A recent discussion has revealed that using DPM_FLAG_SMART_SUSPEND
unconditionally is generally problematic because it may lead to
situations in which the device's runtime PM information is internally
inconsistent or does not reflect its real state [1].
For this reason, change the handling of DPM_FLAG_SMART_SUSPEND so that
it is only taken into account if it is consistently set by the drivers
of all devices having any PM callbacks throughout dependency graphs in
accordance with the following rules:
- The "smart suspend" feature is only enabled for devices whose drivers
ask for it (that is, set DPM_FLAG_SMART_SUSPEND) and for devices
without PM callbacks unless they have never had runtime PM enabled.
- The "smart suspend" feature is not enabled for a device if it has not
been enabled for the device's parent unless the parent does not take
children into account or it has never had runtime PM enabled.
- The "smart suspend" feature is not enabled for a device if it has not
been enabled for one of the device's suppliers taking runtime PM into
account unless that supplier has never had runtime PM enabled.
Namely, introduce a new device PM flag called smart_suspend that is only
set if the above conditions are met and update all DPM_FLAG_SMART_SUSPEND
users to check power.smart_suspend instead of directly checking the
latter.
At the same time, drop the power.set_active flage introduced recently
in commit 3775fc538f ("PM: sleep: core: Synchronize runtime PM status
of parents and children") because it is now sufficient to check
power.smart_suspend along with the dev_pm_skip_resume() return value
to decide whether or not pm_runtime_set_active() needs to be called
for the device.
Link: https://lore.kernel.org/linux-pm/CAPDyKFroyU3YDSfw_Y6k3giVfajg3NQGwNWeteJWqpW29BojhQ@mail.gmail.com/ [1]
Fixes: 7585946243 ("PM: sleep: core: Restrict power.set_active propagation")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci
Link: https://patch.msgid.link/1914558.tdWV9SEqCh@rjwysocki.net
Pull mfd updates from Lee Jones:
- Fix race in device_node_get_regmap() using more extensive locking
- Remove unused platform driver support for syscon
- Allow syscon nodes to be registered without a "syscon" compatible
string
- Make `platform_data` pointer const in struct mfd_cell
- Revert support for multiple AXP PMICs to avoid regressions
- Increase SoundWire attach timeout and use gpiod_set_raw() for GPIO
operation
- Store the result from fault_log() for use by other sub-components
- Fix an invalid regmap-config max_register value
- Add another Gemini Lake ISA bridge PCI device ID
- Use devm_register_power_off_handler() to simplify code
- Add support for QNAP microcontroller units, including LEDs, input,
and hwmon
- Use MFD_CELL macros and remove unused code
- Add support for AAEON UP board FPGA
- Remove unused includes
- Fix various typos and compatibility issues in multiple bindings
- Add new bindings for rk3562 QoS, LED1202, and qcom,tcsr-ipq5424
- Convert several bindings to YAML schema
- Update sprd,sc2731 bindings to reference sprd,sc2731-efuse bindings
directly
- Fix rohm,bd71815 bindings by correcting resistor values and typos
- Documentation improvements:
- Add documentation for LED1202 and qnap-mcu-hwmon
- Adjust the file entry for the qnap-mcu header in MAINTAINERS
* tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (35 commits)
MAINTAINERS: Adjust the file entry for the qnap-mcu header
dt-bindings: mfd: syscon: Fix ti,j784s4-acspcie-proxy-ctrl compatible
dt-bindings: mfd: syscon: Fix al,alpine-sysfabric-service compatible
Revert "mfd: axp20x: Allow multiple regulators"
dt-bindings: mfd: syscon: Add rk3562 QoS register compatible
mfd: syscon: Allow syscon nodes without a "syscon" compatible
mfd: syscon: Remove the platform driver support
mfd: syscon: Fix race in device_node_get_regmap()
dt-bindings: mfd: atmel: Convert to YAML schema
dt-bindings: mfd: atmel,at91sam9260: Convert to YAML schema
dt-bindings: mfd: sprd,sc2731: Reference sprd,sc2731-efuse bindings
mfd: tps65219: Remove unused macros & add regmap.h
mfd: tps65219: Use MFD_CELL macros
leds: Add LED1202 I2C driver
dt-bindings: leds: Add LED1202 LED Controller
Documentation:leds: Add leds-st1202.rst
mfd: Add support for AAEON UP board FPGA
mfd: da9052: Store result from fault_log
mfd: intel_soc_pmic_chtdc_ti: Fix invalid regmap-config max_register value
mfd: cs42l43: Use devres for remove as well
...
of_syscon_register_regmap() was added for nodes which need a custom
regmap setup. It's not really correct for those nodes to claim they are
compatible with "syscon" as the default handling likely doesn't work in
those cases. If device_node_get_regmap() happens to be called first,
then of_syscon_register() will be called and an incorrect regmap will be
created (barring some other error). That may lead to unknown results in
the worst case. In the best case, of_syscon_register_regmap() will fail
with -EEXIST. This problem remains unless these cases drop "syscon" (an
ABI issue) or we exclude them using their specific compatible. ATM,
there is only one user: "google,gs101-pmu"
There are also cases of adding "syscon" compatible to existing nodes
after the fact in order to register the syscon. That presents a
potential DT ABI problem. Instead, if there's a kernel change needing a
syscon for a node, then it should be possible to allow the kernel to
register a syscon without a DT change. That's only possible by using
of_syscon_register_regmap() currently, but in the future we may want to
support a match list for cases which don't need a custom regmap.
With this change, the lookup functions will succeed for any node
registered by of_syscon_register_regmap() regardless of whether the node
compatible contains "syscon".
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241217-syscon-fixes-v2-3-4f56d750541d@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The platform driver is dead code. It is not used by DT platforms since
commit bdb0066df9 ("mfd: syscon: Decouple syscon interface from
platform devices") which said:
For non-DT based platforms, this patch keeps syscon platform driver
structure so that syscon can be probed and such non-DT based drivers
can use syscon_regmap_lookup_by_pdev API and access regmap handles.
Once all users of "syscon_regmap_lookup_by_pdev" migrated to DT based,
we can completely remove platform driver of syscon, and keep only helper
functions to get regmap handles.
The last user of syscon_regmap_lookup_by_pdevname() was removed in 2018.
syscon_regmap_lookup_by_pdevname() was then removed in 2019, but that
commit failed to remove the rest of the platform driver.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241217-syscon-fixes-v2-2-4f56d750541d@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
It is possible for multiple, simultaneous callers calling
device_node_get_regmap() with the same node to fail to find an entry in
the syscon_list. There is a period of time while the first caller is
calling of_syscon_register() that subsequent callers also fail to find
an entry in the syscon_list and then call of_syscon_register() a second
time.
Fix this by keeping the lock held until after of_syscon_register()
completes and adds the node to syscon_list. Convert the spinlock to a
mutex as many of the functions called in of_syscon_register() such as
kzalloc() and of_clk_get() may sleep.
Fixes: bdb0066df9 ("mfd: syscon: Decouple syscon interface from platform devices")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20241217-syscon-fixes-v2-1-4f56d750541d@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
The max_register = 128 setting in the regmap config is not valid.
The Intel Dollar Cove TI PMIC has an eeprom unlock register at address 0x88
and a number of EEPROM registers at 0xF?. Increase max_register to 0xff so
that these registers can be accessed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241208150028.325349-1-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Currently the device is powered down in the remove callback, however
all other clean up is done through devres. The problem here is the
MFD children are cleaned up through devres. As this happens after
the remove callback has run, this leads to the incorrect ordering
where the child remove functions run after the device has been powered
down. Put the power down into devres as well such that everything runs
in the expected order.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20241205115822.2371719-4-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
The GPIO framework supports specifying if a GPIO is active low or
high and will invert accordingly. Whilst specifying this is part of
the normal GPIO definition flow on device tree systems, it is a DSD
extension under ACPI, that Windows doesn't really use. This means most
ACPI systems do not set the polarity of the pin.
The current cs42l43 driver assumes it is setting the level of the line
directly, which is actually the case on all current systems and likely
most future ones. However if the part was used in a device tree system
or an ACPI system that actually used the DSD extensions this would get
inverted, causing the driver to fail probe. As the driver always knows
the polarity of its own reset line, use the raw set API making the
intention to set the level directly clear and to avoid any such future
issues.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20241205115822.2371719-2-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
These microcontroller units are used in network-attached-storage devices
made by QNAP and provide additional functionality to the system.
This adds the base driver that implements the serial protocol via
serdev and additionally hooks into the poweroff handlers to turn
off the parts of the system not supplied by the general PMIC.
Turning off (at least the TSx33 devices using Rockchip SoCs) consists of
two separate actions. Turning off the MCU alone does not turn off the main
SoC and turning off only the SoC/PMIC does not turn off the hard-drives.
Also if the MCU is not turned off, the system also won't start again until
it is unplugged from power.
So on shutdown the MCU needs to be turned off separately before the
main PMIC.
The protocol spoken by the MCU is sadly not documented, but was
obtained by listening to the chatter on the serial port, as thankfully
the "hal_app" program from QNAPs firmware allows triggering all/most
MCU actions from the command line.
The implementation of how to talk to the serial device got some
inspiration from the rave-sp servdev driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241107114712.538976-5-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
