The current PHY2 LED define are wrong and actually set BITs outside the
related mask. Fix it and set the correct value. While at it, also use
FIELD_PREP_CONST macro to make it simple to understand what values are
actually applied for the mask.
Also fix wrong PHY LED mapping. The SoC Switch supports up to 4 port but
the register define mapping for 5 PHY port, starting from 0. The mapping
was wrongly defined starting from PHY1. Reorder the function group to
start from PHY0. PHY4 is actually never supported as we don't have a
GPIO pin to assign.
Cc: stable@vger.kernel.org
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Reviewed-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/20250401135026.18018-1-ansuelsmth@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The public datasheets of the following Amlogic SoCs describe a typical
resistor value for the built-in pull up/down resistor:
- Meson8/8b/8m2: not documented
- GXBB (S905): 60 kOhm
- GXL (S905X): 60 kOhm
- GXM (S912): 60 kOhm
- G12B (S922X): 60 kOhm
- SM1 (S905D3): 60 kOhm
The public G12B and SM1 datasheets additionally state min and max
values:
- min value: 50 kOhm for both, pull-up and pull-down
- max value for the pull-up: 70 kOhm
- max value for the pull-down: 130 kOhm
Use 60 kOhm in the pinctrl-meson driver as well so it's shown in the
debugfs output. It may not be accurate for Meson8/8b/8m2 but in reality
60 kOhm is closer to the actual value than 1 Ohm.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/20250329190132.855196-1-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"Core changes:
- None really.
New drivers:
- AMD ISP411 "AMD ISP" driver
- Exynos 2200 and 7870 SoC subdrivers
- Sophgo RISC-V SG2042 and SG2044 subdrivers
- Amlogic A4 subdriver
- Rockchip RK3528 subdriver
- Broadcom BCM21664 subdriver
- Allwinner A523/T527 subdriver
- Ingenic X1600 subdriver
- Microchip SAMA7D65 subdriver, essentially a re-branded Atmel AT91
PIO4 driver, but nowadays a Microschip SoC line
Improvements:
- Bring in the devm_kmemdup_array() helper and use it throughout,
also bring in changes to other subsystems for this to establish
this helper
- Support EGPIO on the Qualcomm SA8775P SoC
- Extend EINT support in the Mediatek driver"
* tag 'pinctrl-v6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (101 commits)
pinctrl: mediatek: Add EINT support for multiple addresses
pinctrl: amlogic-a4: Drop surplus semicolon
pinctrl: nuvoton: Reduce use of OF-specific APIs
pinctrl: nuvoton: Convert to use struct group_desc
pinctrl: nuvoton: Make use of struct pinfunction and PINCTRL_PINFUNCTION()
pinctrl: nuvoton: Convert to use struct pingroup and PINCTRL_PINGROUP()
pinctrl: npcm8xx: Fix incorrect struct npcm8xx_pincfg assignment
pinctrl: tegra: Fix off by one in tegra_pinctrl_get_group()
pinctrl: PINCTRL_AMDISP should depend on DRM_AMD_ISP
pinctrl: qcom: sa8775p: Enable egpio function
dt-bindings: pinctrl: qcom: Add egpio function for sa8775p
pinctrl: qcom: tlmm-test: Validate irq_enable delivers edge irqs
pinctrl: qcom: Clear latched interrupt status when changing IRQ type
dt-bindings: pinctrl: airoha: Add missing gpio-ranges property
pinctrl: bcm281xx: Add missing assignment in bcm21664_pinctrl_lock_all()
pinctrl: amd: isp411: Fix IS_ERR() vs NULL check in probe()
dt-bindings: pinctrl: at91-pio4: add microchip,sama7d65-pinctrl
pinctrl: tegra: Set SFIO mode to Mux Register
pinctrl-tegra: Restore SFSEL bit when freeing pins
pinctrl: tegra: Add descriptions for SoC data fields
...
Sparse is not happy about implementation of the NPCM8XX_PINCFG()
pinctrl-npcm8xx.c:1314:9: warning: obsolete array initializer, use C99 syntax
pinctrl-npcm8xx.c:1315:9: warning: obsolete array initializer, use C99 syntax
...
pinctrl-npcm8xx.c:1412:9: warning: obsolete array initializer, use C99 syntax
pinctrl-npcm8xx.c:1413:9: warning: too many warnings
which uses index-based assignment in a wrong way, i.e. it missed
the equal sign and hence the index is simply ignored, while the
entries are indexed naturally. This is not a problem as the pin
numbering repeats the natural order, but it might be in case of
shuffling the entries. Fix this by adding missed equal sign and
reformat a bit for better readability.
Fixes: acf4884a57 ("pinctrl: nuvoton: add NPCM8XX pinctrl and GPIO driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/20250318105932.2090926-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Samsung pinctrl drivers changes for v6.15
1. Add pin controller drivers for newly usptreamed Samsung Exynos2200
and Exynos7870.
2. Correct filter configuration offset of some of Google GS101 SoC pin
banks, which later is supposed to be used during system
suspend/resume.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
Cc: stable@vger.kernel.org
Fixes: cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts when enabling")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20250312-pinctrl-msm-type-latch-v1-1-ce87c561d3d7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra devices have an 'sfsel' bit field that determines whether a pin
operates in SFIO (Special Function I/O) or GPIO mode. Currently,
tegra_pinctrl_gpio_disable_free() sets this bit when releasing a GPIO.
However, tegra_pinctrl_set_mux() can be called independently in certain
code paths where gpio_disable_free() is not invoked. In such cases, failing
to set the SFIO mode could lead to incorrect pin configurations, resulting
in functional issues for peripherals relying on SFIO.
This patch ensures that whenever set_mux() is called, the SFIO mode is
correctly set in the Mux Register if the 'sfsel' bit is present. This
prevents situations where the pin remains in GPIO mode despite being
configured for SFIO use.
Fixes: 971dac7123 ("pinctrl: add a driver for NVIDIA Tegra")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Link: https://lore.kernel.org/20250306050542.16335-1-pshete@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each pin can be configured as a Special Function IO (SFIO) or GPIO,
where the SFIO enables the pin to operate in alternative modes such as
I2C, SPI, etc.
The current implementation sets all the pins back to SFIO mode
even if they were initially in GPIO mode. This can cause glitches
on the pins when pinctrl_gpio_free() is called.
Avoid these undesired glitches by storing the pin's SFIO/GPIO
state on GPIO request and restoring it on GPIO free.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Link: https://lore.kernel.org/20250305104939.15168-2-pshete@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As most other Allwinner SoCs before, the A523 chip contains a second
GPIO controller, managing banks PL and PM.
Use the newly introduced DT based pinctrl driver to describe just the
generic pinctrl properties, so advertise the number of pins per bank
and the interrupt capabilities. The actual function/mux assignment is
taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-9-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner A523 contains pins in 10 out of the 11 possible pin banks;
it just skips port A.
Use the newly introduced DT based pinctrl driver to describe just the
generic pinctrl properties, so advertise the number of pins per bank
and the interrupt capabilities. The actual function/mux assignment is
taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-8-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
So far every Allwinner SoC needs a large table in the kernel code, to
describe the mapping between the pinctrl function names ("uart") and
the actual pincontroller mux value to be written into the registers.
This adds a lot of data into a single image kernel, and also looks
somewhat weird, as the DT can easily store the mux value.
Add some code that allows to avoid that table: the struct that describes
the existing pins will be build at *runtime*, based on very basic
information provided by the respective SoC's pinctrl driver. This
consists of the number of pins per bank, plus information which bank
provides IRQ support, along with the mux value to use for that.
The code will then iterate over all children of the pincontroller DT
node (which describe each pin group), and populate that struct with the
mapping between function names and mux values. The only thing that needs
adding in the DT is a property with that value, per pin group.
When this table is built, it will be handed over to the existing sunxi
pinctrl driver, which cannot tell a difference between a hardcoded
struct and this new one built at runtime. It will take care of
registering the pinctrl device with the pinctrl subsystem.
All a new SoC driver would need to do is to provide two arrays, and then
call the sunxi_pinctrl_dt_table_init() function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-6-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner pincontroller IP features some registers to control the
withstand voltage of each pin group. So far those registers were always
located at the same offset, but the A523 SoC has moved them (probably to
accommodate all eleven pin banks).
Add a flag to note this feature, and use that to program the registers
either at offset 0x340 or 0x380. So far no pincontroller driver uses
this flag, but we need it for the upcoming A523 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-5-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner pincontroller register layout used to allow for at least
11 banks per controller, any more banks would reside at a second
controller instance.
When the per-bank register map size was increased with the D1, it turned
out that the last bank (port K) of those maximum 11 banks actually would
not fit anymore in the 512 bytes reserved for the pincontroller registers.
On new SoCs Allwinner thus moved the last bank beyond the existing
registers, at offset 0x500.
So far SoCs never used more than 9 banks per controller, but the new
Allwinner A523 actually uses all 11 banks. Since that SoC also uses the
extended layout, its PortK needs to be programmed at offset 0x500.
Factor out the bank offset calculation into a new function, and handle
the case for the last bank separately. Since none of the older SoCs ever
used PortK, we can ignore this case, and just always use offset 0x500
for the last bank.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/20250306235827.4895-4-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By design, the Allwinner pinctrl IP always supported up to 11 GPIO banks,
though no SoC ever used more than 9 banks so far.
The Allwinner A523 has pins in all 11 banks, which exceeds the number of
per-bank regulators that we currently support, as this was set to 9.
Increase the size of the array to hold up to 11 regulator structs, to
support pins in bank J and K as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/20250306235827.4895-3-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For some Allwinner SoCs we have one pinctrl driver caring for multiple
very similar chips, and are tagging certain pins with a variant bitmask.
The Allwinner D1 introduced a slightly extended register layout, and we
were abusing this variant mask to convey this bit of information into
the common code part.
Now there will be more pinctrl device properties to consider (has PortF
voltage switch, for instance), so shoehorning this into the variant
bitmask will not fly anymore.
Refactor the "variant" field into a more generic "flags" field. It turns
out that we don't need the variant bits to be unique across all SoCs,
but only among those SoCs that share one driver (table), of which there
are at most three variants at the moment. So the actual variant field can
be limited to say 8 bits, and the other bits in the flag register can be
re-purposed to hold other information, like this extended register
layout.
As a side effect we can move the variant definition into the per-SoC
pinctrl driver file, which makes it more obvious that this is just a
private definition, only relevant for this particular table.
This also changes the artificial sun20i-d1 "variant" into the actual
flag bit that we are after.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/20250306235827.4895-2-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v6.15-1
* Introduce devm_kmemdup_array() and convert Intel pin control drivers
* Update PWM handling for the cases when it's provided by Intel pin control
* Miscellaneous fixes, updates, and cleanups
The following is an automated git shortlog grouped by driver:
baytrail:
- copy communities using devm_kmemdup_array()
- Use dedicated helpers for chained IRQ handlers
cherryview:
- use devm_kmemdup_array()
devres:
- Introduce devm_kmemdup_array()
driver core:
- Split devres APIs to device/devres.h
err.h:
- move IOMEM_ERR_PTR() to err.h
iio:
- adc: xilinx-xadc-core: use devm_kmemdup_array()
- imu: st_lsm9ds0: Replace device.h with what is needed
input:
- ipaq-micro-keys: use devm_kmemdup_array()
- sparse-keymap: use devm_kmemdup_array()
intel:
- drop repeated config dependency
- copy communities using devm_kmemdup_array()
- Fix wrong bypass assignment in intel_pinctrl_probe_pwm()
- Import PWM_LPSS namespace for devm_pwm_lpss_probe()
lynxpoint:
- Use dedicated helpers for chained IRQ handlers
MAINTAINERS:
- Add pin control and GPIO to the Intel MID record
pwm:
- lpss: Clarify the bypass member semantics in struct pwm_lpss_boardinfo
- lpss: Actually use a module namespace by defining the namespace earlier
pxa2xx:
- use devm_kmemdup_array()
tangier:
- use devm_kmemdup_array()
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
BCM21664 is another chip from the Kona line of Broadcom SoCs, and
its pinmux shares a lot of similarities with the BCM281xx pinmux.
Add support for the BCM21664 pinmux controller to the BCM281xx driver.
This also enables pinmux support for the BCM23550, which has an
identical pinmux config to the BCM21664 (hence they can share a
single compatible, brcm,bcm21664-pinctrl).
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/20250303-bcm21664-pinctrl-v3-4-5f8b80e4ab51@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce a new struct type, "bcm281xx_pinctrl_info", that holds
information about the pins, pin functions and regmap config for a pin
control chip. Create such a struct for the BCM218xx and pass it as
device data for the OF compatible match.
This is done in preparation for introducing additional chip types
to the driver.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/20250303-bcm21664-pinctrl-v3-3-5f8b80e4ab51@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
