Samsung DTS ARM changes for v5.1, part 2
1. Enable ADC on Odroid HC1 board.
2. Fix clkout register failure on Exynos3250.
3. Allow using earlycon on Arndale board.
4. Disable ARM PMU on Odroid XU3 Lite because it is locked by Trusted
Firmware.
5. Add support for secondary DAI to Odroid XU3 and XU4 boards.
* tag 'samsung-dt-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 482997699e ("ARM: tegra: Fix unit_address_vs_reg DTC warnings
for /memory") inadventently broke device tree ABI by adding a unit-
address to the "/memory" node because the device tree compiler flagged
the missing unit-address as a warning.
Tegra124 Chromebooks (a.k.a. Nyan) use a bootloader that relies on the
full name of the memory node in device tree being exactly "/memory". It
can be argued whether this was a good decision or not, and some other
bootloaders (such as U-Boot) do accept a unit-address in the name of the
node, but the device tree is an ABI and we can't break existing setups
just because the device tree compiler considers it bad practice to omit
the unit-address nowadays.
This partially reverts the offending commit and restores device tree ABI
compatibility.
Fixes: 482997699e ("ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory")
Reported-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
marvell,dsa properties has been removed from kirkwood-rd88f6281.dtsi
while cleanuping the dsa binding, but the dsa reference in
kirkwood-rd88f6281-z0.dts has been missed causing the following errors:
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:21.4-16: Warning (reg_format): /dsa/switch@0:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:23.5-15: Warning (reg_format): /dsa/switch@0/port@4:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:20.12-26.5: Warning (avoid_default_addr_size): /dsa/switch@0: Relying on default #address-cells value
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:20.12-26.5: Warning (avoid_default_addr_size): /dsa/switch@0: Relying on default #size-cells value
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:22.11-25.6: Warning (avoid_default_addr_size): /dsa/switch@0/port@4: Relying on default #address-cells value
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:22.11-25.6: Warning (avoid_default_addr_size): /dsa/switch@0/port@4: Relying on default #size-cells value
So remove the dsa reference too in order to fix this issue.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3b79919946 ("ARM: dts:
armada-370-xp: update NAND node with new bindings") updated some
Marvell Armada DT description to use the new NAND controller bindings,
but did it incorrectly for a number of boards: armada-xp-gp,
armada-xp-db and armada-xp-lenovo-ix4-300d. Due to this, the NAND is
no longer detected on those platforms.
This commit fixes that by properly using the new NAND DT binding. This
commit was runtime-tested on Armada XP GP, the two other platforms are
only compile-tested.
Fixes: 3b79919946 ("ARM: dts: armada-370-xp: update NAND node with new bindings")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch extends DAPM routing and adds secondary CPU DAI entry
to support the secondary audio PCM interface on Odroid XU4.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch extends DAPM routing and adds secondary CPU DAI entry
to support the secondary audio PCM interface on Odroid XU3.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
ARM Performance Monitoring Units (PMUs) are permanently disabled in the
Exynos5422 SoC version used on Odroid XU3-lite boards. Disable them in
boards dtb to avoid confusing user and getting following warning on boot:
hw-breakpoint: Failed to enable monitor mode on CPU 0
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace bootargs and kernel console parameter with 'stdout-path' property
in 'chosen' node to instruct kernel which serial driver should be used
for the kernel console and logs. This allows to enable earlycon messages
by adding just 'earlycon' parameter to kernel command line.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add minimal parameters needed by the Exynos CLKOUT driver to Exynos3250
PMU node. This fixes the following warning on boot:
exynos_clkout_init: failed to register clkout clock
Fixes: d19bb397e1 ("ARM: dts: exynos: Update PMU node with CLKOUT related data")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Odroid HC1 uses the exynos5422-odroid-core.dtsi file as a base. All
other Exynos5422 Odroids use the "common". The ADC node was defined
only in the latter.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A number of improvements for rv1108 boards, removal of an obsolete property
from the Edison tablet and a chosen node for veyron devices.
* tag 'v5.1-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add chosen node on veyron devices
ARM: dts: rockchip: remove cap-mmc-highspeed from rk3188-bqedison2qc mmc1 node
ARM: dts: rockchip: Use the correct regulator properties on rv1108-evb
ARM: dts: rockchip: Use the correct regulator properties on rv1108-elgin
ARM: dts: rockchip: Fix vcc5/6-supply representation on rv1108-elgin
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
gpio updates for v5.1
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
In order to use earlycon, the stdout-path property needs to be set
in the chosen node. All veyron devices use uart2 for debugging, so
add it to the core veyron dtsi.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The mmc1 pins are used for SDIO with a wifi chip.
The function mmc_sdio_switch_hs() only checks for MMC_CAP_SD_HIGHSPEED and
not for MMC_CAP_MMC_HIGHSPEED, so cap-mmc-highspeed can be removed.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Qualcomm Device Tree Changes for v5.1 - Part 2
* Fix MSI IRQ type on IPQ4019
* tag 'qcom-dts-for-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom: ipq4019: Fix MSI IRQ type
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM/ARM64/MIPS based SoCs changes
for 5.1, please pull the following:
- Stefan updates the BCM2835 SoC driver with downstream properties and
uses that to implement a reboot notifier to tell the VC4 firmware when
Linux on the ARM CPU is rebooting
- Eric adds a proper power domain driver for the BCM283x SoCs and
updates a bunch of drivers to have a better and clearer Device Tree
definition to support power domains/breaking up of functionality. This
requires converting the existing watchdog driver into a MFD and then
breaking up the functionality into separate drivers and finally
updating the DTS files to leverage the power domains information.
- Wei provides a fix for making a symbol static
* tag 'arm-soc/for-5.1/drivers' of https://github.com/Broadcom/stblinux:
ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.
ARM: bcm283x: Extend the WDT DT node out to cover the whole PM block. (v4)
soc: bcm: bcm2835-pm: Make local symbol static
soc: bcm: Make PM driver default for BCM2835
soc: bcm: bcm2835-pm: Add support for power domains under a new binding.
bcm2835-pm: Move bcm2835-watchdog's DT probe to an MFD.
dt-bindings: soc: Add a new binding for the BCM2835 PM node. (v4)
firmware: raspberrypi: notify VC4 firmware of a reboot
soc: bcm2835: sync firmware properties with downstream
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
More dts changes for omaps
We add support for Bosch Guardian am335x device, and configure more
devices like GNSS and LCD backlight for omap3-gta04. And we replace
the wlcore binding documentation URL with a local file that we have.
* tag 'omap-for-v5.1/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3-gta04: declare backlight in lcd node
ARM: dts: am335x: Add support for Bosch Guardian
ARM: dts: gta04: add gps support
ARM: dts: gta04: add ldo 3v3 regulator
ARM: dts: gta04: add pinctrl settings for wkup domain
ARM: dts: omap3-gta04a5: Replace LXR reference with a local one
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: dts: zynq: DT changes for v5.1
- Use new "wakeup-source" instead of "gpio-key,wakeup" in Z-Turn
* tag 'zynq-dt-for-v5.1' of https://github.com/Xilinx/linux-xlnx:
ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX device tree changes for 5.1:
- New board support: Logic PD i.MX6QD EVM, ZII SSMB DTU, Phytec
phyBOARD i.MX6UL Segin, Y Soft IOTA Draco, Hydra and Ursa boards.
- Add regulator control for various sensors on imx6qdl-sabresd board.
- Add DISPLAY power domain support for i.MX6SX SoC.
- Add stmpe-adc device node for Toradex iMX6 module.
- Switch to SPDX identifier for imx6q-tbs2910 board.
- Add proper ksz9031 clock skew values for imx6qdl-phytec-pfla02 board.
- Mark I2C recovery GPIOs as open drain and correct and WEIM range
configuration for apalis/colibri boards.
- Small and random updates to various devices.
* tag 'imx-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (31 commits)
ARM: dts: imx: Add support for Logic PD i.MX6QD EVM
ARM: dts: imx6qdl-sabresd: remove reg_sensors' regulator-always-on
ARM: dts: imx6qdl-sabresd: add regulators control for mma8451 sensor
ARM: dts: imx6qdl-sabresd: add regulators control for mag3110 sensor
ARM: dts: imx6qdl-sabresd: add regulator control for isl29023 sensor
ARM: dts: vf610: Add ZII SSMB DTU board
ARM: dts: pfla02: add ksz9031 clock skew values
ARM: dts: imx6qdl-phytec-pfla02: add missing interrupt-controller property
ARM: dts: Add stmpe-adc DT node to Toradex iMX6 modules
ARM: dts: Add devicetree compatibles for LS1021A based boards
ARM: dts: colibri: use valid range configuration for weim
ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin
ARM: dts: imx6*-apalis/-colibri: mark I2C recovery GPIOs as open drain
ARM: dts: vf610-zii-ssmb-spu3: Pass "no-sdio"/"no-sd" properties
ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards
ARM: dts: imx7ulp: add sim node
ARM: dts: imx6ull: change to use new compatible "fsl,imx6ull-usdhc" for usdhc
ARM: dts: imx6ull: Fix i.MX6ULL/ULZ ocotp compatible
ARM: dts: imx6sx: Add DISPLAY power domain support
ARM: dts: i.MX51: digi-connectcore-som: Add support for I2C bus recovery
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: dts: Amlogic updates for v5.1
- more features for Endless EC100 board
- chip temperature sensor support
- fix ethernet pins
- add Mali-450 GPU
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: ec100: add the GPIO line names
ARM: dts: meson8b: ec100: improve the description of the regulators
ARM: dts: meson8b: ec100: enable the Ethernet PHY interrupt
ARM: dts: meson8m2: mxiii-plus: add iio-hwmon for the chip temperature
ARM: dts: meson8b: odroidc1: add iio-hwmon for the chip temperature
ARM: dts: meson8b: ec100: add iio-hwmon for the chip temperature
ARM: dts: meson8b: add the temperature calibration data for the SAR ADC
ARM: dts: meson8: add the temperature calibration data for the SAR ADC
ARM: dts: meson8m2: use the Meson8m2 specific SAR ADC compatible
ARM: dts: meson: switch the clock controller to the HHI register area
ARM: dts: meson8b: fix the Ethernet data line signals in eth_rgmii_pins
ARM: dts: meson8b: add the Mali-450 MP2 GPU
ARM: dts: meson8: add the Mali-450 MP6 GPU
dt-bindings: gpu: mali-utgard: add Amlogic Meson8 and Meson8b compatible
ARM: dts: meson8b: add the APB bus
ARM: dts: meson8: add the APB bus
ARM: dts: meson6: add the APB2 bus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mt7623:
- add cooling mask to all CPUs
- add compatible to sysirq binding
* tag 'v5.0-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: interrupt-controller: update bindings for MT7623
ARM: dts: mt7623: Add all CPUs in cooling maps
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: tegra: Device tree changes for v5.1-rc1
Contains a single patch that adds the "jedec,spi-nor" compatible string
where appropriate.
* tag 'tegra-for-5.1-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: add "jedec,spi-nor" flash compatible binding
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas ARM Based SoC DT Updates for v5.1
* R-Car H2 (r8a7790) based Stout board
- Convert to new LVDS DT bindings
* R-Car H1 (r8a7779) and M1A (r8a7778) SoCs
- Describe HSCIF0/1 devices in DT
* RZ/G1M (r8a7743) SoC
- Correct sort order of the RWDT node
- Remove aliases: should be defined in board rather than SoC DT if needed
- Remove generic compatible string from iic3: it is not compatible
* RZ/G1N (r8a7744) SoC
- Describe LVDS and DU devices in DT
- Correct sort order of VSP and MSIOF noces
* RZ/G1C (r8a7747) based iWave SBC
- Enable RTC
* RZ/A2M (r7s9210) SoC and EVB
- Initial support
* tag 'renesas-arm-dt-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7744: Add LVDS support
ARM: dts: r8a7744: Add DU support
ARM: dts: r7s9210-rza2mevb: Add support for RZ/A2M EVB
ARM: dts: r7s9210: Initial SoC device tree
ARM: dts: r8a7779: Add HSCIF0/1 device nodes
ARM: dts: r8a7778: Add HSCIF0/1 support
ARM: dts: r8a7743: Fix sorting of rwdt node
ARM: dts: r8a7743: Remove aliases from SoC dtsi
ARM: dts: r8a7743: Remove generic compatible string from iic3
ARM: dts: r8a7744: Fix sorting of vsp and msiof nodes
ARM: dts: iwg23s-sbc: Enable RTC
ARM: dts: stout: Convert to new LVDS DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allwinner H3 and H5 changes for 5.1
Our usual round of DT changes shared between arm and arm64.
We have a bunch of changes for board, improving the eMMC support on the H5
variant of the All-H3-CC, enabling HDMI and reworking the CSI driver.
* tag 'sunxi-h3-h5-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: libretech-all-h3-cc: Mark eMMC HS-DDR 3.3V capable
ARM: dts: sunxi: h3/h5: Drop A31 fallback compatible for CSI controller
ARM: dts: sun8i-h3: nanopi-m1-plus: enable HDMI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm Device Tree Changes for v5.1
* Fixup GIC IRQ flags and GSBI state on MSM8660
* Add USB OTG, gpio ranges, and Wifi support on MSM8974 Hammerhead
* Remove skeleton.dtsi on IPQ4019
* tag 'qcom-dts-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: ipq4019: Remove skeleton.dtsi
ARM: dts: qcom: msm8974-hammerhead: add USB OTG support
ARM: dts: qcom: msm8974: add gpio-ranges
ARM: dts: qcom: msm8974-hammerhead: add WiFi support
ARM: dts: msm8660: Fix up GIC IRQ flags
ARM: dts: msm8660: Mark two GSBI blocks "disabled"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: lpc32xx: devicetree updates for v5.1
Here are the changes for ARM NXP LPC32xx and ARM NXP LPC18xx/LPC43xx
devicetree files:
* added dts file for MYIR Tech MYD-LPC4357 development board,
* two missing properties are added to LPC32xx keypad controller device
tree node, this fixes a long-standing problem with its initialization,
* LPC32xx PL11x LCD controller device node got corrected properties,
which allows to use it with a new PL11x DRM driver,
* output voltage level on one of Phytec phyCORE-LPC3250 fixed regulators
is corrected, the fix is needed to remove duplicating platform data,
* Phytec phyCORE-LPC3250 board gets a description of a kit LCD panel,
this completes setup of CLCD device tree node for the board,
* added unit addresses to memory device nodes on EA and Phytec boards,
* fixes of ordinary warnings in dts formatting like leading zeroes,
unused address and size cell properties and so on.
* tag 'lpc32xx-dt-for-5.1' of https://github.com/vzapolskiy/linux-lpc32xx:
ARM: dts: lpc32xx: ea3250: beautify gpio keys children nodes
ARM: dts: lpc32xx: ea3250: add unit address to memory device node
ARM: dts: lpc32xx: phy3250: add unit address to memory device node
ARM: dts: lpc32xx: phy3250: setup LCD controller to panel interface
ARM: dts: lpc32xx: phy3250: remove regulators umbrella device node
ARM: dts: lpc32xx: phy3250: fix SD card regulator voltage
ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller clocks property
ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller variant
ARM: dts: lpc32xx: reparent keypad controller to SIC1
ARM: dts: lpc32xx: add required clocks property to keypad device node
ARM: dts: Add DT for MYIR Tech MYD-LPC4357 Development Board
ARM: dts: lpc32xx: Remove leading 0x and 0s from bindings notation
ARM: dts: lpc435x: remove address and size cells from gpio-keys-polled nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.1, please pull the following:
- Dan relicenses the Luxul DTS files to GPL 2.0+/MIT
- Hao adds support for the Phicomm K3 which is a BCM4709 SoC with dual
BCM4366 radio
- Stefan adds support for the Raspberry Pi A+: binding and DTS files. He
also provides a bunch of DTC warning fixes for the different RPi DTS(i)
files and adds support for missing GPIO lines on RPi 2/3
* tag 'arm-soc/for-5.1/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero-w: Drop unnecessary pinctrl
ARM: dts: bcm283x: Add missing GPIO line names
ARM: dts: bcm2837-rpi-3-b-plus: Clarify label for STATUS_LED
ARM: dts: bcm2837-rpi-3-b: Use consistent label for HDMI hotplug
ARM: dts: bcm2835: Fix labels for GPIO 0,1
ARM: dts: bcm2835-rpi: Drop unnecessary #address-cells/#size-cells
ARM: dts: bcm283x: Fix DTC warning for memory node
ARM: dts: add Raspberry Pi 3 A+
dt-bindings: bcm: Add Raspberry Pi 3 A+
ARM: dts: BCM5301X: Add basic DT for Phicomm K3
ARM: dts: BCM53573: Relicense Luxul files to the GPL 2.0+ / MIT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v5.1
1. Extend support for Aries family of mobile devices (e.g. Samsung
Galaxy S) based on S5Pv210 SoC: DRM Rotator, FIMD, PWM vibrator,
power off, touchscreen, Broadcom BCM4329 Bluetooth and cpufreq.
2. Remove hardcoded bootargs on Galaxy S family (proper support in
U-Boot).
3. Fix minor DTC warnings.
4. Fix Exynos4412 Odroid X2/U3 conflicting eMMC GPIO settings and regulator
properties.
5. Fix the eMMC RTSN pin breaking proper reboot on X2.
* tag 'samsung-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix pinctrl definition for eMMC RTSN line on Odroid X2/U3
ARM: dts: exynos: Fix eMMC regulator properties on Odroid U3 boards
ARM: dts: exynos: Fix conflicting fixed-regulator GPIO flags and properties
ARM: dts: s3c2416: Fix xti node's missing reg property warning
ARM: dts: s5pv210: Fix onenand's unit address format warning
ARM: dts: s5pv210: Add DMC nodes
ARM: dts: s5pv210: Add support for more devices present on Aries
ARM: dts: s5pv210: Add reserved memory for MFC on Aries
ARM: dts: s5pv210: Remove hardcoded bootargs on Galaxy S and Fascinate 4G
ARM: dts: s5pv210: Use correct fimd variant
ARM: dts: s5pv210: Add node for exynos-rotator
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
STM32 DT updates for v5.1, round 1
Highlights:
----------
MPU part:
-Enable Digital Thermal Sensor (dts) on stm32mp157c-ed1 (and so ev1).
MCU part:
-Add SPI support on stm32f429 SOC (4 SPIs instances).
* tag 'stm32-dt-for-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Enable thermal sensor support on STM32MP157c-ed1
ARM: dts: stm32: add SPI support on STM32F429 SoC
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New board the Elgin-R1 based on the rv1108 soc and a number of small
improvements for rv1108 as well. RK3066 got support for the core
display components and the Edison tablet got its touchscreen added.
Apart from that a wider fix to drop display-wp usage from places where
it shouldn't be used, a pin fix for Edison and a cleanup to prevent
rk3036 board from defining sound-dai-cells for core components in
each board separately.
* tag 'v5.1-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: clean up the abuse of disable-wp
ARM: dts: rv1108: Add support for rv1108-elgin-r1 board
dt-bindings: Add vendor prefix for elgin
ARM: dts: rockchip: rv1108: Add spim0 and spim1 pinctrl groups
ARM: dts: rockchip: Add missing dma-names SPI support for rv1108
ARM: dts: rockchip: add rk3066 vop display nodes
ARM: dts: rockchip: add focaltech touchscreen to rk3188-bqedison2qc
ARM: dts: rockchip: fix cif1_pdn pin on rk3188-bqedison2qc
ARM: dts: rockchip: add HCLK_HDMI to rk3066 vio power-domain
ARM: dts: rockchip: move rk3036 i2s sound-dail-cells into soc dtsi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DaVinci device-tree updates for v5.1 contains a patch to enable analog
mic input on da850 LCDK board.
* tag 'davinci-for-v5.1/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Enable the analog mic input
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dts updates for omap variants for v5.1 merge window
This series contains board specific dts updates and few minor
clean-up changes:
- add stdout-path for am335x-chiliboard
- add wlcore wakeirq for omap3-evm, pandaboard and omap4-droid4
- remove unnecessary address-cells and io-cells for am33xx
- replace deprecated linux,wakeup with wakeup-source property
- use spdx license for am335x-shc
- configure ethernet pins for omap4-sdp
* tag 'omap-for-v5.1/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-sdp: Make ethernet working even if booted with latest u-boot
ARM: dts: am335x-shc.dts: Switch to SPDX identifier
ARM: dts: am437x: replace linux,wakeup with wakeup-source property
ARM: dts: am33xx: Remove unnecessary properties
ARM: dts: omap4-droid4: Configure wlcore wakeirq
ARM: dts: Configure wlcore wakeirq for pandaboard
ARM: dts: Add wlcore wakeirq for omap3-evm
ARM: dts: am335x-chiliboard: Add stdout-path property
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dts updates for ti81xx for v5.1 merge window
Two changes to add support for McGill University's IceBoard telescope
ARM + FPGA instrumentation board. This board is used for several
telescopes around the world, see the related device tree commit for
some interesting links for more information.
Note that these changes are based on the related ti81xx soc changes.
* tag 'omap-for-v5.1/dt-ti-81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874
ARM: dts: ti81xx: Add dts boilerplate for all GPIO and SPI peripherals
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Drop one non-existent component from powerdomain list.
* tag 'v5.0-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove qos_cif1 from rk3188 power-domain
SoC fixes for omaps for v5.0-rc cycle
This series contains two SoC regression fixes and one uninitialized
variable fix:
- Fix inverted nirq pin handling for omap5 that started producing
warnings with earlier GIC direction checks and took a while to
understand and confirm. Basically there are two sys_nirq pins
that are bypassing peripheral modules and inverted automatically
by the SoC and need to be handled with a custom irq_set_type()
- Recent ti-sysc changes caused a regression to the pwm-omap-dmtimer
code where the device tree handling code for timer source clock
gets confused. It looks like we can remove that code eventually,
but for now we just drop a bogus pm_runtime_irq_safe() for the
timers with the related quirks caused by pm_runtime_irq_safe(),
and have the standard assigned-clocks and assigned-clock-parents
deal with setting the source clock
- Fix potentially uninitialized value for display init code if
regmap_read() fails
* tag 'omap-for-v5.0/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Variable "reg" in function omap4_dsi_mux_pads() could be uninitialized
ARM: dts: Configure clock parent for pwm vibra
bus: ti-sysc: Fix timer handling with drop pm_runtime_irq_safe()
ARM: OMAP5+: Fix inverted nirq pin interrupts with irq_set_type
clocksource: timer-ti-dm: Fix pwm dmtimer usage of fck reparenting
Before we fixed up the interrupt hierarchy for the SSBI
GPIO controller, we had to use the PM8058 directly to pick
interrupts. After making the interrupt controller work properly,
we can reference the real interrupt parent.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
Note that the IRQs started at 24 instead of 192 like all of the other
PMICs. This is the same IRQs as the MPP for this board. qcom-pm8xxx.c
doesn't set the shared IRQs so this is highly likely to be a copy and
paste error.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on an APQ8060 DragonBoard with no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the PHY as a new node. The PCI-e controller node gains a
phandle property that points to it.
There isn't yet any code in the kernel that uses this device's
registers, but it will be added for a PCIe PLL erratum workaround.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The lcd display of the gta04 has a backlight but the backlight
was not referenced in the lcd node, so screen blanking did
not turn off the backlight. Fix that.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
