This patch defines OOP tables for all CPUs, similarly to
what done by Takeshi Kihara and Yoshihiro Kaneko for the
R8A77990.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When commit 022bccb840 ("dts: arm64/sdm845: Add WCN3990 WLAN module
device node") was posted upstream no clocks were specified. However,
when the pack was picked into the Chrome OS kernel tree (allegedly
directly from the mailing list post) it had clock properties.
I presume that the clock should be there, so let's add it.
Fixes: 022bccb840 ("dts: arm64/sdm845: Add WCN3990 WLAN module device node")
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[bjorn: Add also the required iommus property]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Change the SDMMC clock source to support a maximum frequency of 200 MHz
on Tegra194.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add SDMMC initial pad offsets used by auto calibration process.
Add SDMMC fixed drive strengths for Tegra210, Tegra186 and
Tegra194 which are used when calibration timeouts.
Fixed drive strengths are based on Pre SI Analysis of the pads.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add nodes required for communication through the Tegra Combined UART.
This includes the AON HSP instance, addition of shared interrupts
for the TOP0 HSP instance, and finally the TCU node itself. Also
mark the HSP instances as compatible to tegra194-hsp, as the hardware
is not identical but is compatible to tegra186-hsp.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix apb, cbus, hiu and periph regions which are not aligned
with the documentation and the information provided by Amlogic
Fixes: 9c8c52f7cb ("arm64: dts: meson-g12a: add initial g12a s905d2 SoC DT support")
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The USB controllers need to be associated with their respective IOMMU
bank, so define this on the dwc3 nodes.
Also add dma-ranges to the qcom-dwc3 nodes to make the bus' DMA mask
propagate to the dwc3 controller instances.
Fixes: 4429e57567 ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
With apps_smmu initializing the SMMU we must specify iommus property for
the sdhc controller.
Fixes: 4429e57567 ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since all cpus in the big and little clusters, respectively, are in the
same frequency domain, use all of them for mitigation in the
cooling-map. We end up with two cooling devices - one each for the big
and little clusters.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The apcs node has #clock-cells = <0>, which means that those who
references it should specify 0 arguments.
The apcs reference in the cpu node incorrectly specifies an argument,
remove this bogus argument.
Fixes: 65afdf4583 ("arm64: dts: qcom: msm8916: Add CPU frequency scaling support")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Libre Computer ALL-H3-CC H5 is one of the few boards that can have
its eMMC run at HS-DDR speed mode. Mark it as such.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On these A64 devices, the DC input jacks are wired to the ACIN pins of
the PMIC, which is represented by the AC power supply. With the
exception of the Nanopi A64, all devices include LiPo batteries or have
connectors for them, which are represented by the battery power supply.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Ensure the PCIe endpoint card reset that is toggled by the PCIe
controller itself is muxed correctly on the EspressoBin.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
On Marvell Armada 3700 SoCs there are two USB2 UTMI PHYs. They are
both very similar but only one has OTG/charging capabilities.
Because there are USB host registers and PHY registers mixed in a
single area, a system controller is also created and referenced from
both the USB host node and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The specification splits the USB2 memory region into three sections:
1/ 0xD005E000-0xD005EFFF: USB2 Host Controller Registers
2/ 0xD005F000-0xD005F7FF: USB2 UTMI PHY Registers
3/ 0xD005F800-0xD005FFFF: USB2 Host Miscellaneous Registers
Section 1/ belongs to the USB2 node but section 2/ belongs to the UTMI
PHY node. Section 3/ can be accessed by both the USB controller and
the PHY because of the miscaellaneous nature of the registers inside
so a specific node will be created to cover the area and a handle to
it will be added in both the USB controller and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fix the SATA IP memory area which is only 0x178 bytes long (from
Marvell A3700 specification). Actually, starting from the offset
0xe0178, there is an area dedicated to the COMPHY driver.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Somewhere along recent changes to power control of the wl1835, power-on
became very unreliable on the hikey, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms, the
hikey would already be happy with 1 ms. Still, we use the safer 10 ms,
like on the Ultra96.
Fixes: ea45267873 ("arm64: dts: hikey: Fix WiFi support")
Cc: <stable@vger.kernel.org> #4.12+
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Enable the gpu node and add the supplying regulator
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit enable the hdmi-sound and i2s2 devices needed to have
audio over HDMI on both rock960 and the related ficus board.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add RSC (Resource State Coordinator) provider
dictating network-on-chip interconnect bus performance
found on SDM845-based platforms.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds a reference to the dts of the Raspberry Pi 3 A+,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
