[Why]
Change DCN10 hubbub to use hubbub as a base and allow all future DCN
hubbubs to do the same instead of using DCN10_hubbub. This increases
readability and doesn't require future hubbubs to inherit anything
other than the base hubbub struct.
[How]
Create separate DCN10_hubbub struct which uses the hubbub struct as
a base.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On DCN1, there is an issue where on high BW config on single channel
systems, underflow will be observed if DCC is disabled. This issue
can be observed on several use cases. For this particular case,
it is observed when playing 4k video on 4k desktop with video downscaled
to a certain size.
[How]
Block MPO for this particular case, this will prevent extra BW consumed
from downscaling, working around the underflow.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The aux_engine struct is needlessly complex and
is defined multiple times. It contains function pointers
that each have only one version and are called only from
inside dce_aux.
[How]
Replace aux_engine with a new struct called dce_aux.
Remove all function pointers and call functions directly.
Remove unused functions
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Users would like more accurate pixel clocks, especially for fractional
"TV" frame rates like 59.94 Hz.
[How]
Store and communicate pixel clocks with 100 Hz accuracy from
dc_crtc_timing through to BIOS command table setpixelclock call.
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_stream_state containing a pointer to sink is poor design.
Sink describes the display, and the specifications or capabilities
it has. That information is irrelevant for dc_stream_state, which describes
hardware state, and is generally used for hardware programming. It
could further be argued that dc_sink itself is just a convenience dc
provides, and DC should be perfectly capable of programming hardware
without any dc_sinks (for example, emulated sinks).
[how]
Phase 1:
Deprecate use of dc_sink pointer in dc_stream. Most references are trivial
to remove, but some call sites are risky (such as is_timing_changed) with
no obvious logical replacement. These will be removed in follow up change.
Add dc_link pointer to dc_stream. This is the typical reason DC really needed
sink pointer, and most call sites are replaced with this.
DMs also need minor updates, as all 3 DMs leverage stream->sink for
some functionality. this is replaced instead by a pointer to private data
inside dc_stream_state, which is used by DMs as a quality of life improvment
for some key functionality. it allows DMs to set pointers have to their own objects
which associate OS objects to dc_stream_states (such as DisplayTarget
and amdgpu_dm_connector). Without the private pointer, DMs would be
forced to perform a lookup for callbacks.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for clock debug logging. With the exception of removing
max_supported_dppclk_khz from logs, there are no functional changes.
[How]
Add clk_bypass struct and clean up buffer logic
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Su Chung <Su.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to disable EDP backlight when enter S4 with EDP only
and resume from S4 with secondary only.
[How]
Align the real hw and sw state via vBios scratch register in
function enable_accelerated_mode when resume from S4.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need separate feature flag for DP 4:2:0 support, since existing
flag is used for HDMI
[How]
Added dp_ycbcr420_supported to struct encoder_feature_support
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is done to clear up the clock programming sequence
since the only time we need to notify pplib is after
clock update.
This also renames the clk block to dccg, at the moment
this block contains both clock management and dccg
functionality.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
ddc engines were recently changed to be independently tracked
from pipe count. the change was reflected in resource constructor
but not in destructor. this manifests as a memory leak when
pipe harvesting is enabled, since not all constructed ddc engines
are freed
[how]
make destructor symmetric with constructor for all dcX_resource
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All ASICS we support has YCbCr support, so
the check is unnecessary, the currently logic
in validate output also returns true all
the time, so the unneccessary logic is removed
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously bandwidth validation was failing because swizzle mode was not
initialized during plane_state allocation. The swizzle mode was
calculated using pixed format which is how swizzle mode is initially
calculated in addrlib.
[How]
* Set default swizzle mode for validation to DC_SW_UNKNOWN
* Created new function in dcn10_assign_swizzle_mode which sets the
plane swizzle mode based on selected pixed format
* Added the call of assign_swizzle_mode into dc_validate_global_state
* Set failsafe swizzle mode back to DC_SW_LINEAR
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clock sources currently have support for asic specific
function pointers. But actual separation into functions
was never performed, leaving us with giant functions that
rely on switch.
This change creates separate functions, removing switch use.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
AMD Stoney reference board, there are only 2 pipes (not include
underlay), and 3 connectors. resource creation, only
2 I2C/AUX engines are created. Within dc_link_aux_transfer, when
pin_data_en =2, refer to enengines[ddc_pin->pin_data->en] = NULL.
NULL point is referred later causing system crash.
[how]
each asic design has fixed number of ddc engines at hw side.
for each ddc engine, create its i2x/aux engine at sw side.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I2C code did not match dc resource model and was generally
unpleasant
[How]
Move code into new svelte dce_i2c files, replacing various i2c
objects with two structs: dce_i2c_sw and dce_i2c_hw. Fully split
sw and hw code paths. Remove all redundant declarations. Use
address lists to distinguish between versions. Change dce80 code
to newer register access macros.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
engine and aux_engine are unnecessary layers we want to remove this
layer.
[How]
flatten engine and aux engine structs into one struct called
aux_engine and remove all references to the engine struct.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Aux engine is created from i2caux layer. We want to remove this layer
and use the engine directly.
[How]
Decouple aux engine from i2caux. Move aux engine related code to dce folder and use
dc resource pool to manage the engine. And use the engine functions directly
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why] dp hbr2 eye diagram pattern for raven asic is not stabled.
workaround is to use tp4 pattern. But this should not be
applied to asic before raven.
[how] add new bool varilable in asic caps. for raven asic,
use the workaround. for carrizo, vega, do not use workaround.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the powerplay debug flag to false for both Windows and Linux
to allow the calls to pplib. So we can retrieve the clock values
from powerplay instead of using default hardcoded values.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
for any reason, if driver detects HUBP underflow,
if a debug option enabled to enable recovery.
it will kick in a sequence of recovery.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move DCN1 implementation of stream encoder to new file (instead
of common dce_stream_encoder.c).
Cleanup code related to different implementation due to register
definition differences.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Video playback shows tearing when adjusting
brightness through radeon custom settings.
- Now added double buffer mechanism to switch
input CSC from register buffer ICSC and COMA
- Improved tab alignment
Signed-off-by: Xingyue Tao <xingyue.tao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change make sure bandwidth is set properly.
For increase bandwidth, set bandwidth before backend
and front end programming.
For decrease bandwidth, set bandwidth after.
To avoid smu hang when reboot and dpms due to 0 disp clk,
keep min disp clock as 100Mhz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
