The current EINVAL value is more applicable to embedded library, where
user can actually put the fixed value to the sensor. In case of the
driver if the value of the channel is invalid it is better in inform
userspace that Channel was out of range as that implies more to internal
driver error than invalid input. It also makes for easier debugging of
where the error comes from during the development.
Signed-off-by: Crt Mori <cmo@melexis.com>
Link: https://lore.kernel.org/r/565d4df2592d751dc0f40908f2569b7c9af8e56e.1663834141.git.cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The sensor can operate in lower power modes and even make measurements when
in those lower powered modes. The decision was taken that if measurement
is not requested within 2 seconds the sensor will remain in SLEEP_STEP
power mode, where measurements are triggered on request with setting the
start of measurement bit (SOB). In this mode the measurements are taking
a bit longer because we need to start it and complete it. Currently, in
continuous mode we read ready data and this mode is activated if sensor
measurement is requested within 2 seconds. The suspend timeout is
increased to 6 seconds (instead of 3 before), because that enables more
measurements in lower power mode (SLEEP_STEP), with the lowest refresh
rate (2 seconds).
Signed-off-by: Crt Mori <cmo@melexis.com>
Link: https://lore.kernel.org/r/be405068f081f2d518843897b13cd0289c280b5d.1663834141.git.cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
The conversion slightly changes the logic behind property reading for
the configuration values. Original code allocates just as much memory
as needed. Then for each separate 32- or 64-bit value it reads it from
the property and converts to a raw one which will be fed to the sensor.
In the new code we allocate the amount of memory needed to retrieve all
values at once from the property and then convert them as required.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220307203606.87258-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
The vendor introduced an updated revision of IQS620A(T) silicon
which is backwards-compatible with previous revisions, the only
exception being the offset used to derive temperature.
Enable this new revision by returning the appropriate offset as
a function of the hardware number provided by the parent MFD.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
sysfs_emit() is preferred over raw s*printf() for sysfs attributes since it
knows about the sysfs buffer specifics and has some built-in checks for
size and alignment.
Use sysfs_emit() to format the custom ``in_filter_notch_center_frequency`
and fault_ovuv` device attributes of the max31865 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211216185217.1054495-10-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
sysfs_emit() is preferred over raw s*printf() for sysfs attributes since it
knows about the sysfs buffer specifics and has some built-in checks for
size and alignment.
Use sysfs_emit() to format the custom `fault_ovuv`, `fault_oc` and
`in_temp_filter_notch_center_frequency` device attributes of the max31856
driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211216185217.1054495-9-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If there are no channels defined in the devicetree, there's no point in
probing the device. We were actually requesting a zero sized 'kmalloc'
array but since we were not touching the ZERO_SIZE_PTR afterwards,
nothing bad was actually happening. Hence this is not really a fix but
rather an improvement.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210825084149.11587-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no reason to assume that the IRQ rising edge (indicating that
the device start up phase is done) will happen after we request the IRQ.
If the device is already up by the time we request it, the call to
'wait_for_completion_timeout()' will timeout and we will fail the device
probe even though there's nothing wrong.
Fix it by just polling the status register until we get the indication that
the device is up and running. As a side effect of this fix, requesting the
IRQ is also moved to after the setup function.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Reported-and-tested-by: Drew Fustini <drew@pdp7.com>
Reviewed-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210811133220.190264-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the device is probed, there's no guarantee that the device is not in
power-down mode. This can happen if the driver is unregistered and
re-probed.
To make sure this doesn't happen, the value of the TMP006_CONFIG register
(which is read in the probe function and stored in the device's private
data) is being checked to see if the MOD bits have the correct value.
This is a fix for a somewhat-rare corner case. As it stands, this doesn't
look like a high priority to go into the Fixes route.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210624081924.15897-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the driver to register via devm_iio_device_register().
For the tmp006_powerdown() hook, this uses a devm_add_action() hook to put
the device in powerdown mode when it's unregistered.
With these changes, the remove hook can be removed.
The i2c_set_clientdata() call is staying around as the private data is used
in the PM routines.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210624081924.15897-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
During commit 067fda1c06 ("iio: hid-sensors: move triggered buffer
setup into hid_sensor_setup_trigger"), the
iio_triggered_buffer_{setup,cleanup}() functions got moved under the
hid-sensor-trigger module.
The above change works fine, if any of the sensors get built. However, when
only the common hid-sensor-trigger module gets built (and none of the
drivers), then the IIO_TRIGGERED_BUFFER symbol isn't selected/enforced.
Previously, each driver would enforce/select the IIO_TRIGGERED_BUFFER
symbol. With this change the HID_SENSOR_IIO_TRIGGER (for the
hid-sensor-trigger module) will enforce that IIO_TRIGGERED_BUFFER gets
selected.
All HID sensor drivers select the HID_SENSOR_IIO_TRIGGER symbol. So, this
change removes the IIO_TRIGGERED_BUFFER enforcement from each driver.
Fixes: 067fda1c06 ("iio: hid-sensors: move triggered buffer setup into hid_sensor_setup_trigger")
Reported-by: Thomas Deutschmann <whissi@gentoo.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210414084955.260117-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
