Pull input fix from Dmitry Torokhov:
"A small fixup to the Zinitix touchscreen driver to avoid enabling the
IRQ line before we successfully requested it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: zinitix - make sure the IRQ is allocated before it gets enabled
The supply names of the Zinitix touchscreen were a bit confused, the new
bindings rectifies this.
To deal with old and new devicetrees, first check if we have "vddo" and in
case that exists assume the old supply names. Else go and look for the new
ones.
We cannot just get the regulators since we would get an OK and a dummy
regulator: we need to check explicitly for the old supply name.
Use struct device *dev as a local variable instead of the I2C client since
the device is what we are actually obtaining the resources from.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Slightly changed the legacy regulator detection]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-4-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The power button on Cherry Trail systems with an AXP288 PMIC is connected
to both the power button pin of the PMIC as well as to a power button GPIO
on the Cherry Trail SoC itself. This leads to double power button event
reporting which is a problem.
Since reporting power button presses through the PMIC is not supported on
all PMICs used on Cherry Trail systems, we want to keep the GPIO
power button events, so the axp20x-pek code checks for the presence of
a GPIO power button and in that case does not register its input-device.
On most systems the GPIO power button also can wake-up the system from
suspend, so the axp20x-pek driver would also not register its interrupt
handler. But on some systems there was a bug causing wakeup by the GPIO
power button handler to not work.
Commit 9747070c11 ("Input: axp20x-pek - always register interrupt
handlers") was added as a work around for this registering the axp20x-pek
interrupts, but not the input-device on Cherry Trail systems.
In the mean time the root-cause of the GPIO power button wakeup events
not working has been found and fixed by the "pinctrl: cherryview: Do not
allow the same interrupt line to be used by 2 pins" patch,
so this is no longer necessary.
This reverts the workaround going back to only registering the
interrupt handlers on systems where we also register the input-device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20220106111647.66520-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Two small fixups for spaceball joystick driver and appletouch touchpad
driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: spaceball - fix parsing of movement data packets
Input: appletouch - initialize work before device registration
Pull input fixes from Dmitry Torokhov:
"A few small updates to drivers.
Of note we are now deferring probes of i8042 on some Asus devices as
the controller is not ready to respond to queries first time around
when the driver is compiled into the kernel"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
Input: atmel_mxt_ts - fix double free in mxt_read_info_block
Input: goodix - fix memory leak in goodix_firmware_upload
Input: goodix - add id->model mapping for the "9111" model
Input: goodix - try not to touch the reset-pin on x86/ACPI devices
Input: i8042 - enable deferred probe quirk for ASUS UM325UA
Input: elantech - fix stack out of bound access in elantech_change_report_id()
Input: iqs626a - prohibit inlining of channel parsing functions
Input: i8042 - add deferred probe support
The open delay time has to be applied only on the first sample of the
X/Y coordinates because on the following samples the ADC channel is not
changed. Removing this time from the samples after the first one,
"ti,coordinate-readouts" greater than 1, decreases the total acquisition
time, allowing to increase the number of acquired coordinates in the time
unit.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-4-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".
Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.
Fixes: 1b8be32e69 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some Silead touchscreens have support for an active (battery powered)
pen, add support for this.
So far pen-support has only been seen on X86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new properties are deliberately not added
to the existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately, at the time of writing this commit message, we have been
unable to get permission from Silead, or from device OEMs, to distribute
the necessary Silead firmware files in linux-firmware.
On a whole bunch of devices the UEFI BIOS code contains a touchscreen
driver, which contains an embedded copy of the firmware. The fw-loader
code has a "platform" fallback mechanism, which together with info on the
firmware from drivers/platform/x86/touchscreen_dmi.c will use the firmware
from the UEFI driver when the firmware is missing from /lib/firmware. This
makes the touchscreen work OOTB without users needing to manually download
the firmware.
The firmware bundled with the original Windows/Android is usually newer
then the firmware in the UEFI driver and it is better calibrated. This
better calibration can lead to significant differences in the reported
min/max coordinates.
Add support for a new (optional) "silead,efi-fw-min-max" property which
provides a set of alternative min/max values to use for the x/y axis when
the EFI embedded firmware is used.
The new property is only used on (x86) devices which do not use devicetree,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added to the
existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When converting a rumble into a periodic effect, for compatibility,
the magnitude is effectively calculated using:
magnitude = max(strong_rubble / 3 + weak_rubble / 6, 0x7fff);
The rumble magnitudes are both u16 and the resulting magnitude is
s16. The max is presumably an attempt to limit the result of the
calculation to the maximum possible magnitude for the s16 result,
and thus should be a min.
However in the case of strong = weak = 0xffff, the result of the first
part of the calculation is 0x7fff, meaning that the min would be
redundant anyway, so simply remove the current max.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211130135039.13726-1-ckeepax@opensource.cirrus.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca9 ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some automated builds report a stack frame size in excess of 2 kB for
iqs626_probe(); the culprit appears to be the call to iqs626_parse_prop().
To solve this problem, specify noinline_for_stack for all of the
iqs626_parse_*() helper functions which are called inside a for loop
within iqs626_parse_prop().
As a result, a build with '-Wframe-larger-than' as low as 512 is free of
any such warnings.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20211129004104.453930-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When booting the xenbus driver will wait for PV devices to have
connected to their backends before continuing. The timeout is different
between essential and non-essential devices.
Non-essential devices are identified by their nodenames directly in the
xenbus driver, which requires to update this list in case a new device
type being non-essential is added (this was missed for several types
in the past).
In order to avoid this problem, add a "not_essential" flag to struct
xenbus_driver which can be set to "true" by the respective frontend.
Set this flag for the frontends currently regarded to be not essential
(vkbs and vfb) and use it for testing in the xenbus driver.
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211022064800.14978-2-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull HID updates from Jiri Kosina:
- support for Nintendo Switch Pro Controllers and Joy-Cons (Daniel J.
Ogorchock)
- support for new revision of the NitroKey U2F device firmware (Andrej
Shadura)
- LED handling improvements for Sony Playstation5 controllers (Roderick
Colenbrander)
- support for Apple 2021 Magic Keyboard (Alex Henrie)
- other assorted code cleanups and new device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (41 commits)
HID: nintendo: fix -Werror build
HID: playstation: require multicolor LED functionality
HID: u2fzero: properly handle timeouts in usb_submit_urb
HID: u2fzero: clarify error check and length calculations
HID: u2fzero: Support NitroKey U2F revision of the device
HID: wacom: Make use of the helper function devm_add_action_or_reset()
HID: wacom: Shrink critical section in `wacom_add_shared_data`
HID: nintendo: prevent needless queueing of the rumble worker
HID: nintendo: ratelimit subcommands and rumble
HID: nintendo: improve rumble performance and stability
HID: nintendo: add IMU support
HID: nintendo: add support for reading user calibration
HID: nintendo: add support for charging grip
HID: nintendo: set controller uniq to MAC
HID: nintendo: reduce device removal subcommand errors
HID: nintendo: patch hw version for userspace HID mappings
HID: nintendo: send subcommands after receiving input report
HID: nintendo: improve subcommand reliability
HID: nintendo: add rumble support
HID: nintendo: add home led support
...
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (86 commits)
tty: Fix extra "not" in TTY_DRIVER_REAL_RAW description
serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE
tty: rpmsg: Define tty name via constant string literal
tty: rpmsg: Add pr_fmt() to prefix messages
tty: rpmsg: Use dev_err_probe() in ->probe()
tty: rpmsg: Unify variable used to keep an error code
tty: rpmsg: Assign returned id to a local variable
serial: stm32: push DMA RX data before suspending
serial: stm32: terminate / restart DMA transfer at suspend / resume
serial: stm32: rework RX dma initialization and release
serial: 8250_pci: Remove empty stub pci_quatech_exit()
serial: 8250_pci: Replace custom pci_match_id() implementation
serial: xilinx_uartps: Fix race condition causing stuck TX
serial: sunzilog: Mark sunzilog_putchar() __maybe_unused
Revert "tty: hvc: pass DMA capable memory to put_chars()"
Revert "virtio-console: remove unnecessary kmemdup()"
serial: 8250_pci: Replace dev_*() by pci_*() macros
serial: 8250_pci: Get rid of redundant 'else' keyword
serial: 8250_pci: Refactor the loop in pci_ite887x_init()
tty: add rpmsg driver
...
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- AMD-PMC S0ix support fixes and improvements
- HP-WMI support for Omen laptops
- New nvidia-wmi-ec-backlight driver
- New Intel ISH ECLITE driver
- WMI core cleanups
- Support for various new Melanox platforms
- System76 Laptop support improvements
- Surface Laptop Studio support and initial Surface Pro 8 support
- Various other small fixes and hardware-id additions"
* tag 'platform-drivers-x86-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (106 commits)
platform/x86: system76_acpi: Fix input device error handling
platform/x86: touchscreen_dmi: Add info for the Viglen Connect 10 tablet
platform/surface: aggregator_registry: Add initial support for Surface Pro 8
platform/x86: mlx-platform: Add support for new system SGN2410
platform/x86: mlx-platform: Add BIOS attributes for CoffeeLake COMEx based systems
platform/x86: mlx-platform: Extend FAN and LED configuration to support new MQM97xx systems
platform/x86: asus-wmi: rename platform_profile_* function symbols
platform/x86: hp-wmi: rename platform_profile_* function symbols
platform/x86: amd-pmc: Drop check for valid alarm time
platform/x86: amd-pmc: Downgrade dev_info message to dev_dbg
platform/x86: amd-pmc: fix compilation without CONFIG_RTC_SYSTOHC_DEVICE
platform/x86: system76_acpi: fix Kconfig dependencies
platform/x86: barco-p50-gpio: use KEY_VENDOR for button instead of KEY_RESTART
platform/x86: sony-laptop: replace snprintf in show functions with sysfs_emit
platform/x86: lg-laptop: replace snprintf in show functions with sysfs_emit
docs: ABI: fix documentation warning in sysfs-driver-mlxreg-io
platform/x86: wmi: change notification handler type
HID: surface-hid: Allow driver matching for target ID 1 devices
HID: surface-hid: Use correct event registry for managing HID events
platform/surface: aggregator_registry: Add support for Surface Laptop Studio
...
