ASPM issues may result in the NIC not being accessible any longer.
In this case disabling ASPM may not work. Therefore detect this case
by checking whether register reads return ~0, and try to make the
NIC accessible again by resetting the secondary bus.
v2:
- add exception handling for the case that pci_reset_bus() fails
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When close device, if wol is enabled, rx will be enabled. When open
device it will cause rx packet to be dma to the wrong memory address
after pci_set_master() and system log will show blow messages.
DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write] Request device [02:00.0] PASID ffffffff fault addr
ffdd4000 [fault reason 05] PTE Write access is not set
In this patch, driver disable tx/rx when close device. If wol is
enabled, only enable rx filter and disable rxdv_gate(if support) to
let hardware only receive packet to fifo but not to dma it.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change. Moving these two functions for following
patch "r8169: fix dmar pte write access is not set error".
Signed-off-by: Chunhao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are reports about r8169 not reaching full line speed on certain
systems (e.g. SBC's) with a 2.5Gbps link.
There was a time when hardware interrupt coalescing was enabled per
default, but this was changed due to ASPM-related issues on few systems.
So let's use software interrupt coalescing instead and enable it
using new function netdev_sw_irq_coalesce_default_on().
Even with these conservative settings interrupt load on my 1Gbps test
system reduced significantly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The open code is defined as a helper function(tp_to_dev) on r8169_main.c,
which the open code is &tp->pci_dev->dev. The helper function was added
in commit 1e1205b7d3 ("r8169: add helper tp_to_dev"). And then later,
commit f1e911d5d0 ("r8169: add basic phylib support") added
r8169_phylink_handler function but it didn't use the helper function.
Thus, tp_to_dev() replaces the open code. This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20221129161244.5356-1-claudiajkang@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rtl_disable_rxdvgate() is used for disable RXDV_GATE. It is opposite function
of rtl_enable_rxdvgate().
Disable RXDV_GATE does not have to delay. So in this patch, also remove the
delay after disale RXDV_GATE.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Link: https://lore.kernel.org/r/20220928171356.3951-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're not in a hot path and don't want to miss this message,
therefore remove the net_ratelimit() check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's trust the hardware here and remove this useless check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have devm_clk_get_optional_enabled(), we don't have to
open-code it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not clear where these entries came from, and as I wrote in the
comment: Not even Realtek's r8101 driver knows these chip id's.
So remove the comment.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not clear why XID's 380 and 381..387 ever got different chip
version id's. VER_12 and VER_17 are handled exactly the same.
Therefore merge handling under the VER_17 umbrella.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
v3:
- rebase patch
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
v2:
- fix a typo: RTL_GIGA_MAC_VER_40 -> RTL_GIGA_MAC_VER_50
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of these chip versions has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch all Ethernet drivers which use custom napi weights
to the new API.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
atp.h is included only by atp.c, which does not use eeprom_delay(). Remove
the unused definition.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rtl8168d_2_hw_phy_config() shares quite some functionality with
rtl8168d_1_hw_phy_config(), so let's factor out the common part to a
new function rtl8168d_1_common(). In addition improve the code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtl_disable_exit_l1() for ensuring that the chip doesn't
inadvertently exit ASPM L1 when being in a low-power mode.
The new function is called from rtl_prepare_power_down() which
has to be moved in the code to avoid a forward declaration.
According to Realtek OCP register 0xc0ac shadows ERI register 0xd4
on RTL8168 versions from RTL8168g. This allows to simplify the
code a little.
v2:
- call rtl_disable_exit_l1() also if DASH or WoL are enabled
Suggested-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some systems there are compatibility issues with ASPM L1.2 and
RTL8125, therefore this state is disabled per default. To allow for
the L1.2 power saving on not affected systems, Realtek provides
vendors that successfully tested ASPM L1.2 the option to flag this
state as safe. According to Realtek this flag will be set first on
certain Chromebox devices.
Suggested-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull power management updates from Rafael Wysocki:
"The most signigicant change here is the addition of a new cpufreq
'P-state' driver for AMD processors as a better replacement for the
venerable acpi-cpufreq driver.
There are also other cpufreq updates (in the core, intel_pstate, ARM
drivers), PM core updates (mostly related to adding new macros for
declaring PM operations which should make the lives of driver
developers somewhat easier), and a bunch of assorted fixes and
cleanups.
Summary:
- Add new P-state driver for AMD processors (Huang Rui).
- Fix initialization of min and max frequency QoS requests in the
cpufreq core (Rafael Wysocki).
- Fix EPP handling on Alder Lake in intel_pstate (Srinivas
Pandruvada).
- Make intel_pstate update cpuinfo.max_freq when notified of HWP
capabilities changes and drop a redundant function call from that
driver (Rafael Wysocki).
- Improve IRQ support in the Qcom cpufreq driver (Ard Biesheuvel,
Stephen Boyd, Vladimir Zapolskiy).
- Fix double devm_remap() in the Mediatek cpufreq driver (Hector
Yuan).
- Introduce thermal pressure helpers for cpufreq CPU cooling (Lukasz
Luba).
- Make cpufreq use default_groups in kobj_type (Greg Kroah-Hartman).
- Make cpuidle use default_groups in kobj_type (Greg Kroah-Hartman).
- Fix two comments in cpuidle code (Jason Wang, Yang Li).
- Allow model-specific normal EPB value to be used in the intel_epb
sysfs attribute handling code (Srinivas Pandruvada).
- Simplify locking in pm_runtime_put_suppliers() (Rafael Wysocki).
- Add safety net to supplier device release in the runtime PM core
code (Rafael Wysocki).
- Capture device status before disabling runtime PM for it (Rafael
Wysocki).
- Add new macros for declaring PM operations to allow drivers to
avoid guarding them with CONFIG_PM #ifdefs or __maybe_unused and
update some drivers to use these macros (Paul Cercueil).
- Allow ACPI hardware signature to be honoured during restore from
hibernation (David Woodhouse).
- Update outdated operating performance points (OPP) documentation
(Tang Yizhou).
- Reduce log severity for informative message regarding frequency
transition failures in devfreq (Tzung-Bi Shih).
- Add DRAM frequency controller devfreq driver for Allwinner sunXi
SoCs (Samuel Holland).
- Add missing COMMON_CLK dependency to sun8i devfreq driver (Arnd
Bergmann).
- Add support for new layout of Psys PowerLimit Register on SPR to
the Intel RAPL power capping driver (Zhang Rui).
- Fix typo in a comment in idle_inject.c (Jason Wang).
- Remove unused function definition from the DTPM (Dynamit Thermal
Power Management) power capping framework (Daniel Lezcano).
- Reduce DTPM trace verbosity (Daniel Lezcano)"
* tag 'pm-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (53 commits)
x86, sched: Fix undefined reference to init_freq_invariance_cppc() build error
cpufreq: amd-pstate: Fix Kconfig dependencies for AMD P-State
cpufreq: amd-pstate: Fix struct amd_cpudata kernel-doc comment
cpuidle: use default_groups in kobj_type
x86: intel_epb: Allow model specific normal EPB value
MAINTAINERS: Add AMD P-State driver maintainer entry
Documentation: amd-pstate: Add AMD P-State driver introduction
cpufreq: amd-pstate: Add AMD P-State performance attributes
cpufreq: amd-pstate: Add AMD P-State frequencies attributes
cpufreq: amd-pstate: Add boost mode support for AMD P-State
cpufreq: amd-pstate: Add trace for AMD P-State module
cpufreq: amd-pstate: Introduce the support for the processors with shared memory solution
cpufreq: amd-pstate: Add fast switch function for AMD P-State
cpufreq: amd-pstate: Introduce a new AMD P-State driver to support future processors
ACPI: CPPC: Add CPPC enable register function
ACPI: CPPC: Check present CPUs for determining _CPC is valid
ACPI: CPPC: Implement support for SystemIO registers
x86/msr: Add AMD CPPC MSR definitions
x86/cpufeatures: Add AMD Collaborative Processor Performance Control feature flag
cpufreq: use default_groups in kobj_type
...
The pm_ptr() macro should be used when the suspend and resume functions
can be compiled independently of the CONFIG_PM Kconfig option.
In the case of this driver, the suspend and resume functions are inside
a section protected by a #ifdef CONFIG_PM guard. Therefore pm_ptr()
should not be used.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev->gso_max_segs is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add netif_set_gso_max_segs() helper.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_segs()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->gso_max_size is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_size()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems this chip version never made it to the wild. Therefore
disable detection and if nobody complains remove support completely
later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems this chip version never made it to the wild. Therefore
disable detection and if nobody complains remove support completely
later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems these chip versions never made it to the wild. Therefore
disable detection and if nobody complains remove support completely
later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
