[Why & How]
When MST config is unplugged/replugged too quickly, it can potentially
result in a scenario where previous DC state has not been reset before
the HPD link detection sequence begins. In this case, driver will
disable the streams/link prior to re-enabling the link for link
training.
There is a bug in the current logic that does not account for the fact
that current_state can be released and cleared prior to swapping to a
new state (resulting in the pipe_ctx stream pointers to be cleared) in
between disabling streams.
To resolve this, cache the original streams prior to committing any
stream updates.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The response of DP BW allocation is handled in Outbox ISR.
When it failed to request the DP BW allocation, it sent another
DPCD request in Outbox ISR immediately. The DP AUX reply also
uses the Outbox ISR. So, no AUX reply happened in this case.
Change to use HPD IRQ for the notification.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see unstable DP LL 4.2.1.3 test result with dpia pre-train. It is
because the outbox interrupt mechanism can not handle HPD
immediately and require some improvement.
[HOW]
1. not enable link if hpd_pending is true.
2. abort pre-train if training failed and hpd_pending is true.
3. check if 2 lane supported when it is alt mode
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The defines have also been updated with prefix AMD_ and atomfirmware.h
has been temporarily updated with both sets of defines to allow the
transition.
This update is being made to standardize workaround chip_cap flags,
in order to support more workaround flags in the future.
[HOW]
Updated EXT_DISPLAY_PATH_CAPS__DP_FIXED_VS_EN define, the flag is now
an enum masked by EXT_DISPLAY_PATH_CAPS__EXT_CHIP_MASK. All checks for
DP_FIXED_VS_EN are now performed by masking with EXT_CHIP_MASK and
checking for an exact match rather than the previous bitwise AND check.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain small HBlank timings may not have a large enough HBlank to
support audio when low bpp DSC is enabled. HBlank expansion by the
source can solve this problem, but requires the branch/sink to support
HBlank reduction.
[How]
Update DPMS sequence to call DM to perform DPCD write to enable HBlank
reduction on the branch/sink. Add stub in dm_helpers to be implemented
later.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We like to have pretrain for dpia link so that dp and dp tunneling
have aligned behavior. The Main difficult for dpia pretrain is that
encoder can not get corresponded dpia port when link detection
in current implementation.
[HOW]
1. create enable/disable dpia output functions for dcn35 encoder
and have dpia_id and other necessary info as inputs.
2. dcn35 dpia use the new functions to enable/disable output.
3. have a option to enable/disable the change.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
OLED power up sequence takes an extra 150ms via hardcoded delay,
but there is a strict requirement on DisplayOn resume time.
For customer panel, remove these delays to meet target until a
cleaner solution is can be put in place.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Supporting UHBR10 link rate on eDP leverages
the existing DP2.0 code but need to add some small
adjustments in code.
[how]
Acknowledge the given DPCD caps for UHBR10
link rate support and allow DP2.0 programming
sequence and link training for eDP.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The mux to switch between refclk and dto_dsc_clk is non double buffered.
However dto dsc clk's phase and modulo divider registers are currently
configured as double buffered update. This causes a problem when we switch to
use dto dsc clk and program phase and modulo in the same sequence. In this
sequence dsc clk is switched to dto but the clock divider programming doesn't
take effect until next frame. When we try to program DSCC registers, SMN bus
will hang because dto dsc clk divider phase is set to 0.
[how]
Configure phase and modulo to take effect immediately. Always switch to dto dsc
clk before DSC clock is unagted. Switch back to refclk after DSC clock is gated.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
In newer DCN's the programming of SYMCLK_FE_SRC_SEL depends on
the value of DIG_FE_SOURCE_SELECT. If DIG_FE_SOURCE_SELECT is not
already programmed at the time of PHY / DIG enable then the FW
sequence will program an incorrect SYMCLK source. Ensure that we
program DIG_FE_SOURCE_SELECT for all DIO scenarios (DVI in this
particular case) before going through the PHY / DIG enable sequence.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In order to support glitchless display clock ramping for virtual stream,
we must
turn on symclk for stream encoder. The code will power on phy and enable
symclk
for dio encoder during virtual stream dpms sequence.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Switching between DSC clock or disable DSC block are not double buffered update.
Corruption is observed if these updates happen before DSC double buffered
disconnection.
[how]
Move DSC disable and refclk reset to post unlock update. Wait for DSC double buffered
disconnection and all mpccs are disconnected before reset DSC clock.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Upon disconnecting a UHBR SST display, the disconnection and the
SetTimings to disable the display can occur such that link_set_dpms_off
occurs after the disconnection has already processed
(link->type is dc_connection_none). Thus, the AUX related
operations should be skipped when clearing the payload allocation table.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why and how:
as part of cleanup, need to refactor vpg. It was improperly referenced
as a dcn specfic part of link. the dcn agnostic code needed was ripped out
and put into vpg.h, now in dc/inc/hw.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Parandhaman K <parandhaman.k@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Enabling higher compiler warning levels results in many issues that can
be trivially resolved as well as some potentially critical issues.
[how]
Fix all compiler warnings found with various compilers and higher
warning levels. Primarily, potentially uninitialized variables and
unreachable code.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When usb4 bandwidth allocation mode is enabled, driver need to request
bandwidth from connection manager. For mst link, the requested
bandwidth should be big enough for all remote streams.
[HOW]
- If mst link, the requested bandwidth should be the sum of all mst
streams bandwidth added with dp MTPH overhead.
- Allocate/deallcate usb4 bandwidth when setting dpms on/off.
- When doing display mode validation, driver also need to consider total
bandwidth of all mst streams for mst link.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Peichen Huang <peichen.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current implementation will choose to use refclk as dscclk. This is not
recommended by hardware team as refclk is a fixed value which could
cause unnecessary power consumption or it could be not enough for large
DSC timings. So we are adding new interfaces so we could switch to use
dynamically generated DSCCLK by DTO. So DSCCLK is programmable based on
current pixel clock and dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changing PBN calculation to be more in line with spec. We don't need to
inflate PBN_NATIVE value by the 1.006 margin, since that is already
taken care of in the get_pbn_per_slot function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MST relevant variables are maintained at drm side. As the result, we
still have to call drm_dp_remove_payload_part2() to update the relevant
values regardless the link is under mst mode or not. We used to have a
workaround patch to tackle this: commit 3d8fcc6740 ("drm/amd/display:
Extract temp drm mst deallocation wa into its own function")
Now it's time to remove the workaround and adjust the flow.
[How]
During deallocate_mst_payload(), source actually doesn't send out
ALLOCATE_PAYLOAD at the end as like the flow in allocate_mst_payload().
Call function dm_helpers_dp_mst_send_payload_allocation() at the end of
deallocate_mst_payload() is a bit confusing.
Separate dm_helpers_dp_mst_send_payload_allocation() into 2 functions.
Have a new function dm_helpers_dp_mst_update_mst_mgr_for_deallocation()
to replace dm_helpers_dp_mst_send_payload_allocation() for payload
deallocation.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Remove the brightness cache in DC. It uses a single value to represent
the brightness for both SDR and HDR mode. This leads to flash in HDR
on/off. It also unconditionally programs brightness as in HDR mode. This
may introduce garbage on SDR mode in miniLED panel.
[How]
Simplify the initialization flow by removing the DC cache and taking
what panel has as default. Expand the mechanism for PWM to DPCD Aux to
restore cached brightness value generally.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For multi-GPU systems it is difficult to tell which GPU a particular
message is being printed for and that is undesirable because it
complicates debugging efforts. Also, the new macros allow us to enable
logging for particular parts of the codebase more selectively (since we
no longer need to throw everything at DRM_DEBUG_KMS()). So, for the
reasons outlined above we should switch to the new macros.
We can accomplish this by using the existing DC_LOGGER code to pass
around the relevant `struct drm_device` which will be fed to the new
macros in logger_types.h. Also, we must get rid of all instances of the
DC_LOG_.*() functions that are currently in amdgpu_dm since we don't use
the DC logger there and we can simply refer to the macros directly
there instead.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
To organize the edp power control a bit:
1. add flag in dc_link to indicate dc to skip all implicit eDP power control.
2. add edp_set_panel_power link service for DM to call.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a lack of encapsulation of pipe connection representation in pipe context.
This has caused many challenging bugs and coding errors with repeated
logic to identify the same pipe type.
[how]
Formally define pipe types and provide getters to identify a pipe type and
find a pipe based on specific requirements. Update existing logic in non dcn
specific files and dcn32 and future versions to use the new accessors.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There certain cases where the timing BW is dependent on the type of link
encoding in use. Thus to calculate the correct BW required for a given
timing, the link encoding should be added as a parameter.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to save the cached backlight level so that display lights up using
appropriate brightness level instead of the default brightness when
waking up from s0i3.
[How]
Adding a backlight level cache in link structure. Also instead on
calling set_default_brightness_aux, check if cached values exists.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDMI spec requires TMDS clock to be not more than 340MHz. Stream encoder ensure
this requirement but driver enable stream encoder later than PHY. So PHY will
output full speed TMDS clock first.
[How]
Enable stream encoder first in TMDS case.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: JinZe Xu <jinze.xu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The eDP retrain will cause the DPCD 300 to be reset to default.
And cause the brightness can't be set correctly.
[How]
delete the call to edp panel power control in both
enable_link_output/disable_link_output entirely and
only call edp panel control in enable_link_dp and
disable_link_dp once.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Jingwen Zhu <Jingwen.Zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
New sequence for transparent mode DP1.x link training was provided by LTTPR
vendor
[HOW]
Implement new FIXED_VS sequence, increase LT retry count to minimize
any potential intermittent lightup failures
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some dock and mst monitor don't like to receive CLEAR_PAYLOAD_ID_TABLE
when mst_en is set to 0. It doesn't make sense to do so in source
side, either.
[How]
Don't send CLEAR_PAYLOAD_ID_TABLE if mst_en is 0
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
All dc subcomponents should call another dc component via function pointers
stored in a component structure. This is part of dc coding convention since
the beginning. The reason behind this is to improve encapsulation and
polymorphism. The function contract is extracted into a single link service
structure defined in link.h header file and implemented only in link_factory.c instead
of spreading across multiple files in link component file structure.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
