The tc358775 driver follows the drm_encoder->crtc pointer that is
deprecated and shouldn't be used by atomic drivers.
Fortunately, the atomic hooks provide the drm_atomic_state and we can
access our current CRTC from that, going from the bridge to its encoder,
to its connector, and to its CRTC.
Let's convert this bridge driver to atomic so we can get rid of the
drm_encoder->crtc dereference.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-13-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
The tc358775 bridge is pin compatible with earlier tc358765 according to
the tc358774xbg_datasheet_en_20190118.pdf documentation. Compared to the
tc358765, the tc358775 supports a STBY GPIO and higher data rates.
The tc358765 has a register bit for video event mode vs video pulse mode.
We must set it to video event mode for the LCD output to work, and on the
tc358775, this bit no longer exists.
Looks like the registers seem to match otherwise based on a quick glance
comparing the defines to the earlier Android kernel tc358765 driver.
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240225062008.33191-10-tony@atomide.com
The current code assumes the data-lanes property is configured on the
DSI host side instead of the bridge side, and assumes DSI host endpoint 1.
Let's standardize on what the other bridge drivers are doing and parse the
data-lanes property for the bridge. Only if data-lanes property is not found,
let's be nice and also check the DSI host for old dtb in use and warn.
And as Dmitry pointed out, the lanes for the host and the bridge may be
different because the lanes may be swapped on the host side.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240225062008.33191-7-tony@atomide.com
The bridge always uses 24bpp internally. Therefore, for jeida-18
mapping we need to discard the lowest two bits for each channel and thus
starting with LV_[RGB]2. jeida-24 has the same mapping but uses four
lanes instead of three, with the forth pair transmitting the lowest two
bits of each channel. Thus, the mapping between jeida-18 and jeida-24
is actually the same, except that one channel is turned off (by
selecting the RGB666 format in VPCTRL).
While at it, remove the bogus comment about the hardware default because
the default is overwritten in any case.
Tested with a jeida-18 display (Evervision VGG644804).
Fixes: b26975593b ("display/drm/bridge: TC358775 DSI/LVDS driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240225062008.33191-5-tony@atomide.com
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
This driver is tested with two panels individually with Apq8016-IFC6309 board
https://www.inforcecomputing.com/products/single-board-computers-sbc/qualcomm-snapdragon-410-inforce-6309-micro-sbc
1. 1366x768@60 auo,b101xtn01 data-mapping = "jeida-24"
2. 800x480@60 innolux,at070tn92 data-mapping = "vesa-24"
- power off sequence in proper order
- put_unaligned_be16, put_unaligned_le32 macros used
- static function for mode_valid
- len initialized
- MODE_CLOCK_HIGH handled properly
- bus_formats handled in mode_valid
- GENMASK and FIELD_PREP used
- Kconfig proper indentation
- error handling endpoint data-lanes
- check for bus_formats unsupported
- display_timings naming local variables
- help modified
- ~vsdelay dynamic value set based on the
calculation of dsi speed, output speed, blanking
- panel->connector_type removed
- dual port implemented
- devm_drm_panel_bridge_add method used instead of panel
description modified
- regulator enable and disable with proper orders and delays
as per the spec
- removed drm_connector_status
- added bus_formats
- mdelay to usleep_range
- magic number to macros for CLRSI and mux registers
description modified
- replaced u32 instead of uint32_t
- updated alphabetic order of headers
- added SPDX identifier license
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam.ravnborg@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1594388491-15129-2-git-send-email-simhavcs@gmail.com
