On ADLP+ during modeset enabling and disabling, enable and disable the DP2
configuration for MST slave transcoders as required by the specification.
Update the documentation of intel_ddi_config_transcoder_func() /
intel_ddi_disable_transcoder_func() based on the above. While at it also
clarify the programming steps of these functions specific to transcoder
types.
v2:
- Enable/disable the DP2 config from
intel_ddi_config_transcoder_func()/intel_ddi_disable_transcoder_func().
(Jani)
- Handle all ADLP+ platforms in one patch, instead of doing that
separately wrt. PTL.
Bspec: 55424, 54128, 65448, 68849
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030192313.4030617-5-imre.deak@intel.com
On PTL during modeset enabling configure the DDI function without
enabling it for MST slave transcoders before programming the data and
link M/N values. The DDI function gets enabled separately later in the
transcoder enabling sequence.
This fixes a slave transcoder getting stuck during enabling, leading
to page flip timeout errors on the corresponding pipe.
The spec requires the same programming step for ADLP+ platforms, that
will be addressed separately (on those platforms the above transcoder
getting stuck issue was not observed).
Bspec: 68849
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241030192313.4030617-2-imre.deak@intel.com
Changes in Dynamic Range and Mastering infoframe
should not trigger a full modeset. Therefore, allow
fastset. DP SDP programming is already hooked up in the
fastset flow but HDMI AVI infoframe update is not, add it.
Any other infoframe that can be fastset should be added to
the helper intel_hdmi_fastset_infoframes().
v3:
- Create a wrapper intel_ddi_update_pipe_hdmi to stick to
uniform naming (Jani)
- Do not disable HDMI AVI infoframe if already disabled (Uma)
v2:
- Update HDMI AVI infoframe during fastset.
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241023044122.3889137-1-chaitanya.kumar.borah@intel.com
Currently, even though there is a bit to control FEC enable/disable
individually, the FEC Decode Enable sequence is sent by the SOC only
once TRANS_CONF enable is set. This ties the FEC enabling too tightly
to modeset and therefore cannot be re-issued (in case of failure)
without a modeset.
From PTL, FEC_DECODE_EN sequence can be sent to a DPRX independent
of TRANS_CONF enable. This allows us to re-issue an FEC_DECODE_EN
sequence without a modeset. Hence allowing us to have a retry
mechanism in case the DPRX does not respond with an FEC_ENABLE
within certain amount of time.
While at it, replace struct drm_i915_private with struct intel_display
v4:
- More code refactor [Jani]
- use struct intel_display [Jani]
- Optimize logging [Jani]
v3:
- Make the commit message more legible [Jani]
- Refactor code to re-use existing code [Jani]
- Do away with platform dependent FEC enable checks [Jani]
v2:
- Refactor code to avoid duplication and improve readability [Jani]
- In case of PTL, wait for FEC status directly after FEC enable [Srikanth]
- Wait for FEC_ENABLE_LIVE_STATUS to be cleared before
re-enabling FEC [Srikanth]
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241024061002.4085137-1-chaitanya.kumar.borah@intel.com
While updating the source OUI on the sink the driver should avoid
writing the OUI if it's already up-to-date to prevent the sink from
resetting itself in response to the update. On eDP - the only output
type where the OUI was updated so far - the driver ensured this by
comparing the current source OUI DPCD register values with the expected
Intel OUI value, skipping the update in case of a match. On some non-eDP
sinks - at least on Synaptics branch devices - this method doesn't work,
since the source OUI DPCD registers read back as all 0, even after
updating the registers.
Handle the above kind of sinks by tracking when the OUI was updated and
so should be valid, regardless of what the DPCD registers contain.
eDP sinks reset the written source OUI value when the panel power is
disabled, invalidate the OUI state accordingly.
This is required by a follow-up patch updating the source OUI for
non-eDP sink types as well.
v2: Fix setting intel_dp::oui_valid=true, if the DPCD register contains
already the expected value.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-5-imre.deak@intel.com
Joiners have specific enabling and disabling order dependent on primary
and secondary pipes. This becomes more complex with ultrajoiner where we
have ultrajoiner primary/secondary pipes in addition to bigjoiner
primary/secondary pipes. To unify the approach that works for present
and future joiner cases, use primary and secondary pipe masks to
iterate over pipes.
If joiner is used, derive bigoiner primary and secondary pipe masks
and use following sequences:
Disabling : disable primary pipes followed by secondary pipes,
Enabling: enable secondary pipes followed by primary pipes.
This works well with ultrajoiner too, as ultrajoiner has 2 bigjoiner
primary/secondary pairs (AC, BD).
For non joiner case, enable/disable based on usual pipe order A-D, D-A
respectively.
v2:
-Simplify the iterator macro. (Ville)
-Use struct intel_display. (Ville)
-Add prefix _intel to the helper name. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240918063016.2667721-3-ankit.k.nautiyal@intel.com
Panel Self Refresh on eDP requires the AUX IO power to be enabled
whenever the output (main link) is enabled. This is required by the
AUX_PHY_WAKE/ML_PHY_LOCK signaling initiated by the HW automatically to
re-enable the main link after it got disabled in power saving states
(see eDP v1.4b, sections 5.1, 6.1.3.3.1.1).
The Panel Replay mode on non-eDP outputs on the other hand is only
supported by keeping the main link active, thus not requiring the above
AUX_PHY_WAKE/ML_PHY_LOCK signaling (eDP v1.4b, section 6.1.3.3.1.2).
Thus enabling the AUX IO power for this case is not required either.
Based on the above enable the AUX IO power only for eDP/PSR outputs.
Bspec: 49274, 53370
v2:
- Add a TODO comment to adjust the requirement for AUX IO based on
whether the ALPM/main-link off mode gets enabled. (Rodrigo)
Cc: Animesh Manna <animesh.manna@intel.com>
Fixes: b8cf5b5d26 ("drm/i915/panelreplay: Initializaton and compute config for panel replay")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240910111847.2995725-1-imre.deak@intel.com
The next patch adds sending a modeset-retry uevent after a link training
failure to all MST connectors on link. This requires the atomic state,
so pass it to intel_dp_start_link_train(). In case of SST where
retraining still happens by calling this function directly instead of a
modeset commit the atomic state is not available and NULL is passed
instead. This is ok, since in this case the encoder's only DP connector
is available from intel_dp->attached_connector not requiring the atomic
state.
v2: Add NOTE that the atomic state may not be valid for SST links and
assert that it's valid for MST links. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-10-imre.deak@intel.com
Recheck the link state after a passing link training, with a 2 sec delay
to account for cases where the link goes bad following the link training
and the sink doesn't report this via an HPD IRQ.
The delayed work added here will be also used by a later patch after a
failed link training to try to retrain the link with unchanged link
params before reducing the link params.
v2: Don't flush an uninitialized delayed work (on HDMI-only DDI ports).
v3:
- Move the helpers to a new intel_encoder.c file, rename them
accordingly. (Ville)
- Add the work to intel_encoder instead of intel_digital_port.
- Call the encoder specific link check function via an encoder hook.
- Flush the link check work during encoder destroy from
intel_dp_encoder_flush_work().
- Flush the link check work during encoder suspend as well.
v4: Call intel_encoder_link_check_init() with a valid encoder pointer.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610181428.2955658-1-imre.deak@intel.com
