Pass the current pipe into enabled_joiner_pipes(), and let it figure out
the proper bitmasks for us. Since the enabled_joiner_pipes now gets the
primary and secondary pipes wrt a given pipe, the helpers
to get primary pipe and secondary pipes are no longer required.
v2:
-Simplify helper get_joiner_primary_pipes. (Ville)
-Nuke get_joiner_secondary_pipes. (Ville)
-Add more drm_WARNs final primary/secondary pipes. (Ville)
v3: Drop ultrajoiner stuff and add it in subsequent patches. (Ville)
v4:
-Replace input variable name primary_pipes to primary_pipe for
enabled_joiner_pipes()
-Avoid get_joiner_primary_pipe and use primary_pipes set by
enabled_joiner_pipes(). (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-5-ankit.k.nautiyal@intel.com
The ilk+ disable_lp_wm boolean has the exact same role as
disable_cxsr for gmch platforms. The documentation also
still talks about CxSR on ilk+ even theough the way you
control it has now change to involve toggling the LP watermarks.
Get rid of disable_lp_wm and just use disable_cxsr for ilk+
as well.
TODO: Unify even more to not have any gmch vs. ilk+
details in high level modeset code...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240916162413.8555-7-ville.syrjala@linux.intel.com
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Joiners have specific enabling and disabling order dependent on primary
and secondary pipes. This becomes more complex with ultrajoiner where we
have ultrajoiner primary/secondary pipes in addition to bigjoiner
primary/secondary pipes. To unify the approach that works for present
and future joiner cases, use primary and secondary pipe masks to
iterate over pipes.
If joiner is used, derive bigoiner primary and secondary pipe masks
and use following sequences:
Disabling : disable primary pipes followed by secondary pipes,
Enabling: enable secondary pipes followed by primary pipes.
This works well with ultrajoiner too, as ultrajoiner has 2 bigjoiner
primary/secondary pairs (AC, BD).
For non joiner case, enable/disable based on usual pipe order A-D, D-A
respectively.
v2:
-Simplify the iterator macro. (Ville)
-Use struct intel_display. (Ville)
-Add prefix _intel to the helper name. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240918063016.2667721-3-ankit.k.nautiyal@intel.com
In most of the cases we now try to avoid mentioning things like
"bigjoiner" or "ultrajoiner" trying to unify the API and refer
mostly to all this functionality as "joiner".
In majority cases that should be way to go.
However in some cases we still need to distinguish between
bigjoiner primaries and secondaries(such as DSC register programming).
Create correspondent helper functions and start using them,
in order be prepared for adding ultrajoiner functionality.
v2: Fixed checkpatch warnings (Ankit)
v3: Introduce ultrajoiner helpers in next patch.
v4: Streamline the helpers and add few more. (Ville)
v5: Add comment to clarify that helpers apply to both bigjoiner and
uncompressed joiner configurations. (Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240918063016.2667721-2-ankit.k.nautiyal@intel.com
When determining various scanlines for DSB use we should take into
account whether VRR is active at the time when the DSB uses said
scanline information. For now all DSB scanline usage occurs prior
to the actual commit, so we only need to care about the state of
VRR at that time.
I've decided to move intel_crtc_scanline_to_hw() in its entirety
to the DSB code as it will also need to know the actual state
of VRR in order to do its job 100% correctly.
TODO: figure out how much of this could be moved to some
more generic place and perhaps be shared with the CPU
vblank evasion code/etc...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240624191032.27333-8-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
The cursor hardware only does sync updates, and thus the hardware
will be scanning out from the old fb until the next start of vblank.
So in order to make the legacy cursor fastpath actually safe we
should not unpin the old fb until we're sure the hardware has
ceased accessing it. The simplest approach is to just use a vblank
work here to do the delayed unpin.
Not 100% sure it's a good idea to put this onto the same high
priority vblank worker as eg. our timing critical gamma updates.
But let's keep it simple for now, and it we later discover that
this is causing problems we can think about adding a lower
priority worker for such things.
This patch is slightly reworked by Maarten
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240522053341.137592-3-maarten.lankhorst@linux.intel.com
Compute Fixed Average Vtotal/CMRR with resepect to
userspace VRR enablement. Also calculate required
parameters in case of CMRR is enabled. During
intel_vrr_compute_config, CMRR is getting enabled
based on userspace has enabled Variable refresh mode
with VRR timing generator or not. Make CMRR as small subset of
FAVT mode, when Panel is running on Fixed refresh rate
and on VRR framework then only enable CMRR to match with
actual refresh rate.
--v2:
- Update is_cmrr_frac_required function return as bool, not int. [Jani]
- Use signed int math instead of unsigned in cmrr_get_vtotal2. [Jani]
- Fix typo and usage of camel case in cmrr_get_vtotal. [Jani]
- Use do_div in cmrr_get_vtotalwhile calculating cmrr_m. [ Jani]
- Simplify cmrr and vrr compute config in intel_vrr_compute_config. [Jani]
- Correct valiable name usage in is_cmrr_frac_required. [Ville]
--v3:
- Removing RFC tag.
--v4:
- Added edp check to address edp usecase for now. (ville)
- Updated is_cmrr_fraction_required to more simplified calculation.
- on longterm goal to be worked upon uapi as suggestion from ville.
--v5:
- Correct vtotal paramas accuracy and add 2 digit precision.
- Avoid using DIV_ROUND_UP and improve scanline precision.
--v6:
- Make CMRR a small subset of FAVT mode.
--v7:
- Update commit message to avoid confusion with Legacy VRR (Ankit).
- Add cmrr.enable in last, so remove from this patch.
--v8:
- Set cmrr.enable in current patch instead of separate patch (Ankit).
- Since vrr.enable and cmrr.enable are not mutually exclusive,
handle accordingly (Ankit).
- is_edp is not required inside is_cmrr_frac_required function (Ankit).
- Add video_mode_required flag for future enhancement.
- Correct cmrr_m/cmrr_n calculation.
--v9:
- Move patch to last and set other bits before computing
cmrr.enable.(Ankit)
- Add TODO: for to address target refresh rate precision as future
enhancement.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610072203.24956-10-mitulkumar.ajitkumar.golani@intel.com
Add register definitions for Transcoder Fixed Average
Vtotal mode/CMRR function, with the necessary bitfields.
Compute these registers when CMRR is enabled, extending
Adaptive refresh rate capabilities.
--v2:
- Use intel_de_read64_2x32 in intel_vrr_get_config. [Jani]
- Fix indent and order based on register offset. [Jani]
--v3:
- Removing RFC tag.
--v4:
- Update place holder for CMRR register definition. (Jani)
--v5:
- Add CMRR register definitions to a separate file intel_vrr_reg.h.
--v6:
- Fixed indentation. (Jani)
- Add dependency header intel_display_reg_defs.h. (Jani)
- Rename file name to intel_vrr_regs.h instead of reg.h (Jani)
--v7:
- Remove adding CMRR flag to vrr_ctl register during set_transcoder_timing,
as it is already being done during intel_vrr_enable. (Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610072203.24956-4-mitulkumar.ajitkumar.golani@intel.com
