Backmerging to get v6.15-rc1 into drm-misc-next. Also fixes a
build issue when enabling CONFIG_DRM_SCHED_KUNIT_TEST.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Mediatek DRM Next for Linux 6.15
1. HDMI fixup and refinement
2. Move to devm_platform_ioremap_resource() usage
3. Add MT8188 dsc compatible
4. Fix config_updating flag never false when no mbox channel
5. dp: drm_err => dev_err in HPD path to avoid NULL ptr
6. Add dpi power-domains example
7. Add MT8365 SoC support
8. Fix error codes in mtk_dsi_host_transfer()
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250312232909.9304-1-chunkuang.hu@kernel.org
The function mtk_dp_wait_hpd_asserted() may be called before the
`mtk_dp->drm_dev` pointer is assigned in mtk_dp_bridge_attach().
Specifically it can be called via this callpath:
- mtk_edp_wait_hpd_asserted
- [panel probe]
- dp_aux_ep_probe
Using "drm" level prints anywhere in this callpath causes a NULL
pointer dereference. Change the error message directly in
mtk_dp_wait_hpd_asserted() to dev_err() to avoid this. Also change the
error messages in mtk_dp_parse_capabilities(), which is called by
mtk_dp_wait_hpd_asserted().
While touching these prints, also add the error code to them to make
future debugging easier.
Fixes: 7eacba9a08 ("drm/mediatek: dp: Add .wait_hpd_asserted() for AUX bus")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250116094249.1.I29b0b621abb613ddc70ab4996426a3909e1aa75f@changeid/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Pull drm updates from Dave Airlie:
"There are two external interactions of note, the msm tree pull in some
opp tree, hopefully the opp tree arrives from the same git tree
however it normally does.
There is also a new cgroup controller for device memory, that is used
by drm, so is merging through my tree. This will hopefully help open
up gpu cgroup usage a bit more and move us forward.
There is a new accelerator driver for the AMD XDNA Ryzen AI NPUs.
Then the usual xe/amdgpu/i915/msm leaders and lots of changes and
refactors across the board:
core:
- device memory cgroup controller added
- Remove driver date from drm_driver
- Add drm_printer based hex dumper
- drm memory stats docs update
- scheduler documentation improvements
new driver:
- amdxdna - Ryzen AI NPU support
connector:
- add a mutex to protect ELD
- make connector setup two-step
panels:
- Introduce backlight quirks infrastructure
- New panels: KDB KD116N2130B12, Tianma TM070JDHG34-00,
- Multi-Inno Technology MI1010Z1T-1CP11
bridge:
- ti-sn65dsi83: Add ti,lvds-vod-swing optional properties
- Provide default implementation of atomic_check for HDMI bridges
- it605: HDCP improvements, MCCS Support
xe:
- make OA buffer size configurable
- GuC capture fixes
- add ufence and g2h flushes
- restore system memory GGTT mappings
- ioctl fixes
- SRIOV PF scheduling priority
- allow fault injection
- lots of improvements/refactors
- Enable GuC's WA_DUAL_QUEUE for newer platforms
- IRQ related fixes and improvements
i915:
- More accurate engine busyness metrics with GuC submission
- Ensure partial BO segment offset never exceeds allowed max
- Flush GuC CT receive tasklet during reset preparation
- Some DG2 refactor to fix DG2 bugs when operating with certain CPUs
- Fix DG1 power gate sequence
- Enabling uncompressed 128b/132b UHBR SST
- Handle hdmi connector init failures, and no HDMI/DP cases
- More robust engine resets on Haswell and older
i915/xe display:
- HDCP fixes for Xe3Lpd
- New GSC FW ARL-H/ARL-U
- support 3 VDSC engines 12 slices
- MBUS joining sanitisation
- reconcile i915/xe display power mgmt
- Xe3Lpd fixes
- UHBR rates for Thunderbolt
amdgpu:
- DRM panic support
- track BO memory stats at runtime
- Fix max surface handling in DC
- Cleaner shader support for gfx10.3 dGPUs
- fix drm buddy trim handling
- SDMA engine reset updates
- Fix doorbell ttm cleanup
- RAS updates
- ISP updates
- SDMA queue reset support
- Rework DPM powergating interfaces
- Documentation updates and cleanups
- DCN 3.5 updates
- Use a pm notifier to more gracefully handle VRAM eviction on
suspend or hibernate
- Add debugfs interfaces for forcing scheduling to specific engine
instances
- GG 9.5 updates
- IH 4.4 updates
- Make missing optional firmware less noisy
- PSP 13.x updates
- SMU 13.x updates
- VCN 5.x updates
- JPEG 5.x updates
- GC 12.x updates
- DC FAMS updates
amdkfd:
- GG 9.5 updates
- Logging improvements
- Shader debugger fixes
- Trap handler cleanup
- Cleanup includes
- Eviction fence wq fix
msm:
- MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
- DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two
SSPPs for a single plane)
- added CWB hardware blocks support
- DSI:
- added SM6150 (aka QCS615) support
- GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
rcar-du:
- Add r8a779h0 Support
ivpu:
- Fix qemu crash when using passthrough
nouveau:
- expose GSP-RM logging buffers via debugfs
panfrost:
- Add MT8188 Mali-G57 MC3 support
rockchip:
- Gamma LUT support
hisilicon:
- new HIBMC support
virtio-gpu:
- convert to helpers
- add prime support for scanout buffers
v3d:
- Add DRM_IOCTL_V3D_PERFMON_SET_GLOBAL
vc4:
- Add support for BCM2712
vkms:
- line-per-line compositing algorithm to improve performance
zynqmp:
- Add DP audio support
mediatek:
- dp: Add sdp path reset
- dp: Support flexible length of DP calibration data
etnaviv:
- add fdinfo memory support
- add explicit reset handling"
* tag 'drm-next-2025-01-17' of https://gitlab.freedesktop.org/drm/kernel: (1070 commits)
drm/bridge: fix documentation for the hdmi_audio_prepare() callback
doc/cgroup: Fix title underline length
drm/doc: Include new drm-compute documentation
cgroup/dmem: Fix parameters documentation
cgroup/dmem: Select PAGE_COUNTER
kernel/cgroup: Remove the unused variable climit
drm/display: hdmi: Do not read EDID on disconnected connectors
drm/tests: hdmi: Add connector disablement test
drm/connector: hdmi: Do atomic check when necessary
drm/amd/display: 3.2.316
drm/amd/display: avoid reset DTBCLK at clock init
drm/amd/display: improve dpia pre-train
drm/amd/display: Apply DML21 Patches
drm/amd/display: Use HW lock mgr for PSR1
drm/amd/display: Revised for Replay Pseudo vblank control
drm/amd/display: Add a new flag for replay low hz
drm/amd/display: Remove unused read_ono_state function from Hwss module
drm/amd/display: Do not elevate mem_type change to full update
drm/amd/display: Do not wait for PSR disable on vbl enable
drm/amd/display: Remove unnecessary eDP power down
...
Mediatek DRM Fixes - 20250104
1. Revert "drm/mediatek: dsi: Correct calculation formula of PHY Timing"
2. Set private->all_drm_private[i]->drm to NULL if mtk_drm_bind returns err
3. Move mtk_crtc_finish_page_flip() to ddp_cmdq_cb()
4. Only touch DISP_REG_OVL_PITCH_MSB if AFBC is supported
5. Add support for 180-degree rotation in the display driver
6. Stop selecting foreign drivers
7. Revert "drm/mediatek: Switch to for_each_child_of_node_scoped()"
8. Fix YCbCr422 color format issue for DP
9. Fix mode valid issue for dp
10. dp: Reference common DAI properties
11. dsi: Add registers to pdata to fix MT8186/MT8188
12. Remove unneeded semicolon
13. Add return value check when reading DPCD
14. Initialize pointer in mtk_drm_of_ddp_path_build_one()
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250104124227.45505-1-chunkuang.hu@kernel.org
The DP calibration data is stored in nvmem cells, and the data layout is
described in the `mtk_dp_efuse_fmt` arrays for each platform.
There is no guarantee that the data is always a 4-length u32 cell array.
For example, MT8188 has a data length of 3, preventing it from passing
the preliminary check and undergoing calibration.
Update the logic to support flexible data lengths. Specifically, we
validate the length returned from `nvmem_cell_read()` against the
platform-specific efuse format. If out-of-bound access is detected, fall
back to the default calibration values. This likely indicates an error
in either the efuse data length described in DT or the efuse format
within the driver.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241204142626.158395-1-fshao@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fix dp mode valid issue to avoid abnormal display of limit state.
After DP passes link training, it can express the lane count of the
current link status is good. Calculate the maximum bandwidth supported
by DP using the current lane count.
The color format will select the best one based on the bandwidth
requirements of the current timing mode. If the current timing mode
uses RGB and meets the DP link bandwidth requirements, RGB will be used.
If the timing mode uses RGB but does not meet the DP link bandwidthi
requirements, it will continue to check whether YUV422 meets
the DP link bandwidth.
FEC overhead is approximately 2.4% from DP 1.4a spec 2.2.1.4.2.
The down-spread amplitude shall either be disabled (0.0%) or up
to 0.5% from 1.4a 3.5.2.6. Add up to approximately 3% total overhead.
Because rate is already divided by 10,
mode->clock does not need to be multiplied by 10.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Liankun Yang <liankun.yang@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241025083036.8829-3-liankun.yang@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mtk_dp driver registers a phy device which is handled by the
phy_mtk_dp driver and assumes that the phy probe will complete
synchronously, proceeding to make use of functionality exposed by that
driver right away. This assumption however is false when the phy driver
is built as a module, causing the mtk_dp driver to fail probe in this
case.
Add the phy_mtk_dp module as a pre-dependency to the mtk_dp module to
ensure the phy module has been loaded before the dp, so that the phy
probe happens synchrounously and the mtk_dp driver can probe
successfully even with the phy driver built as a module.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231121142938.460846-1-nfraprado@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the mediatek drm drivers from always returning zero in
the remove callback to the void returning variant.
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230801110239.831099-8-u.kleine-koenig@pengutronix.de/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In order to support usecases in which the panel regulator can be
switched on and off to save power, and usecases in which the panel
regulator is off at boot, add a .wait_hpd_asserted() callback for
the AUX bus: this will make sure to wait until the panel is fully
ready after power-on before trying to communicate with it.
Also, parse the eDP display capabilities in that callback, so that
we can also avoid using the .get_edid() callback from this bridge.
Since at this point the hpd machinery is performed in the new hpd
callback and the detection and edid reading are done outside of
this driver, assign the DRM_BRIDGE_OP_{DETECT, EDID, HPD} ops and
register the bridge unconditionally at probe time only if we are
probing full DisplayPort and not eDP while, for the latter, we
register the bridge in the .done_probing() callback and only if
the panel was found and triggered HPD.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-11-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
For the eDP case we can support using aux-bus on MediaTek DP: this
gives us the possibility to declare our panel as generic "panel-edp"
which will automatically configure the timings and available modes
via the EDID that we read from it.
To do this, move the panel parsing at the end of the probe function
so that the hardware is initialized beforehand and also initialize
the DPTX AUX block and power both on as, when we populate the
aux-bus, the panel driver will trigger an EDID read to perform
panel detection.
Last but not least, since now the AUX transfers can happen in the
separated aux-bus, it was necessary to add an exclusion for the
cable_plugged_in check in `mtk_dp_aux_transfer()` and the easiest
way to do this is to simply ignore checking that when the bridge
type is eDP.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-10-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
It is useless and error-prone to enable the DisplayPort event interrupt
before finishing to probe and install the driver, as the DP training
cannot happen before the entire pipeline is correctly set up, as the
interrupt handler also requires the full hardware to be initialized by
mtk_dp_bridge_attach().
Anyway, depending in which state the controller is left from the
bootloader, this may cause an interrupt storm and consequently hang
the kernel during boot, so, avoid enabling the interrupt until we
reach a clean state by adding the IRQ_NOAUTOEN flag before requesting
it at probe time and manage the enablement of the ISR in the .attach()
and .detach() handlers for the DP bridge.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-7-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Everytime we run bridge detection and/or EDID read we run a poweron
and poweroff sequence for both the AUX and the panel; moreover, this
is also done when enabling the bridge in the .atomic_enable() callback.
Move this power on/off sequence to a new mtk_dp_aux_panel_poweron()
function as to commonize it.
Note that, before this commit, in mtk_dp_bridge_atomic_enable() only
the AUX was getting powered on but the panel was left powered off if
the DP cable wasn't plugged in while now we unconditionally send a D0
request and this is done for two reasons:
- First, whether this request fails or not, it takes the same time
and anyway the DP hardware won't produce any error (or, if it
does, it's ignorable because it won't block further commands)
- Second, training the link between a sleeping/standby/unpowered
display makes little sense.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
