The Unicam hardware has been observed to cause a buffer overrun when
using the dummy buffer as a circular buffer. The conditions that cause
the overrun are not fully known, but it seems to occur when the memory
bus is heavily loaded.
To avoid the overrun, program the hardware with a buffer size of 0 when
using the dummy buffer. This will cause overrun into the allocated dummy
buffer, but avoid out of bounds writes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The imx219/imx708 sensors frequently generate a single corrupt frame
(image or embedded data) when the sensor first starts. This can either
be a missing line, or invalid samples within the line. This only occurrs
using the upstream Unicam kernel driver.
Disabling trigger mode elimiates this corruption. Since trigger mode is
a legacy feature copied from the firmware driver and not expected to be
needed, remove it. Tested on the Raspberry Pi cameras and shows no ill
effects.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When matching formats via try_fmt/set_fmt ioctls, test for the unpacked
formats as well as packed formats. This allows userland clients setup
unpacking to 16-bits from the 10/12/14-packed CSI2 formats.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ensure that the frame sequence counter is incremented only if a previous
frame start interrupt has occurred, or a frame start + frame end has
occurred simultaneously.
This corresponds the sequence number with the actual number of frames
produced by the sensor, not the number of frame buffers dequeued back
to userland.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 88785982a1 ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> # for meson-ge2d
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/media to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240506100917.1544174-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The driver can only match the device vide the DT table, so the table
should always be used, of_match_ptr does not make sense here.
It fixes this warning:
drivers/media/platform/broadcom/bcm2835-unicam.c:2724:34: warning: ‘unicam_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
