Add support for the SM8650 platform by re-using the SM8550
definitions and using the vpu33 ops.
Move the Sm8650 reset tables that differs in a per-SoC platform
header, that will contain mode SoC specific data when
more codecs are introduced.
The SM8650/vpu33 requires more reset lines, but the H.264
decoder capabilities are identical.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e Dell
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The IRIS acceleration found in the SM8650 platforms uses the vpu33
hardware version, and requires a slighly different reset and power off
sequences in order to properly get out of runtime suspend.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e Dell
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Introduce an optional controller_rst_tbl use to store reset lines
used to reset part of the controller.
This is necessary for the vpu3 support, when the xo reset line
must be asserted separately from the other reset line
on power off operation.
Factor the iris_init_resets() logic to allow requesting
multiple reset tables.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e Dell
Reviewed-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Build-testing on x86 showed two modules with conflicting "iris.ko"
names after the addition of the qualcomm driver:
error: the following would cause module name conflict:
arch/x86/platform/iris/iris.ko
drivers/media/platform/qcom/iris/iris.ko
Since this a new module, nothing should rely on the name yet, so
rename this one to a more specific "qcom-iris.ko".
Fixes: 38506cb7e8 ("media: iris: add platform driver for iris video device")
Cc: Shérab <Sebastien.Hinderer@ens-lyon.org> # for x86 iris
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
handle the V4L2_DEC_CMD_STOP by initiating a drain sequence on the
firmware. Process and decode all OUTPUT buffers, that are queued by the
client, before the VIDIOC_DECODER_CMD() was issued and mark the last
buffer with the V4L2_BUF_FLAG_LAST flag. The decoder is stopped, after
processing the last buffer.
Resume the decoder when one of these operations are issued by the client:
- V4L2_DEC_CMD_START
- pair of VIDIOC_STREAMOFF() and VIDIOC_STREAMON() on the CAPTURE queue
- pair of VIDIOC_STREAMOFF() and VIDIOC_STREAMON() on the OUTPUT queue
Add the handling to resume decoding when client issues
V4L2_DEC_CMD_START to resume decoding after a source change is detected.
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org> # x1e80100 (Dell XPS 13 9345)
Reviewed-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Handle the response sent by the firmware, when a source change is
detected. Read the subscribed parameter to get the changed values. Raise
the source change event to the client and update the instance sub-state.
Mark the last buffer from before the source change with the
V4L2_BUF_FLAG_LAST flag and return to the client.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org> # x1e80100 (Dell XPS 13 9345)
Reviewed-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Implement the vb2 ops for the buf queue. These are the different buffer
attributes:
BUF_ATTR_DEFERRED - buffer queued by the client but not submitted to
firmware.
BUF_ATTR_PENDING_RELEASE - buffers requested to be released from
the firmware.
BUF_ATTR_QUEUED - buffers submitted to the firmware.
BUF_ATTR_DEQUEUED - buffers received from the firmware.
BUF_ATTR_BUFFER_DONE - buffers sent back to vb2.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org> # x1e80100 (Dell XPS 13 9345)
Reviewed-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
During the stream on operation, send HFI_CMD_START on the capture and
output planes to start processing on the respective planes.
During the stream off operation, send HFI_CMD_STOP to the firmware,
which is a synchronous command. After the response is received by the
firmware, the session is closed on the firmware.
Introduce different states for the instance and state transitions.
IRIS_INST_INIT - video instance is opened.
IRIS_INST_INPUT_STREAMING - stream on is completed on output plane.
IRIS_INST_OUTPUT_STREAMING - stream on is completed on capture plane.
IRIS_INST_STREAMING - stream on is completed on both output and capture
planes.
IRIS_INST_DEINIT - video instance is closed.
IRIS_INST_ERROR - error state.
|
v
-------------
+---------| INIT |--------- +
| ------------- |
| ^ ^ |
| / \ |
| / \ |
| v v |
| ----------- ----------- |
| | INPUT OUTPUT | |
|---| STREAMING STREAMING |---|
| ----------- ----------- |
| ^ ^ |
| \ / |
| \ / |
| v v |
| ------------- |
|--------| STREAMING |-----------|
| ------------- |
| | |
| | |
| v |
| ----------- |
+-------->| DEINIT |<----------+
| ----------- |
| | |
| | |
| v |
| ---------- |
+-------->| ERROR |<-----------+
----------.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org> # x1e80100 (Dell XPS 13 9345)
Reviewed-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Initialize the control handler by reading the platform specific firmware
capabilities. Capabilities are features, which are supported by a
specific platform (SOC). Each capability is defined with a min, max,
range and default value and a corresponding HFI. Implement s_ctrl and
g_volatile_ctrl ctrl ops.
Co-developed-by: Vedang Nagar <quic_vnagar@quicinc.com>
Signed-off-by: Vedang Nagar <quic_vnagar@quicinc.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org> # x1e80100 (Dell XPS 13 9345)
Reviewed-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The Host firmware interface (HFI) is a well defined set of interfaces
for the communication between the host driver and the firmware. The
commands and responses are exchanged in form of packets. One or multiple
packets are grouped under the packet header. Each packet has a packet
type which describes the specific HFI and the payload, which holds the
corresponding value for that HFI.
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org> # x1e80100 (Dell XPS 13 9345)
Reviewed-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Introduce a core state management for iris driver with the necessary
queues needed for the host firmware communication.
There are 3 types of queues:
Command queue - driver to write any command to firmware.
Message queue - firmware to send any response to the driver.
Debug queue - for the firmware to write debug messages.
Initialize and configure the shared queues during probe.
Different states for core:
IRIS_CORE_DEINIT - default state.
IRIS_CORE_INIT - core state with core initialized. FW loaded and HW
brought out of reset, shared queues established
between host driver and firmware.
IRIS_CORE_ERROR - error state.
-----------
|
V
-----------
| DEINIT |
-----------
^
/ \
/ \
/ \
/ \
v v
----------- ----------.
| INIT |-->| ERROR |
----------- ----------.
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org> # x1e80100 (Dell XPS 13 9345)
Reviewed-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Implement open, close and poll ops.
Open:
Configure the vb2 queue and v4l2 file handler. Allocate a video instance
and add the instance to core instance list.
Close:
Free the instance and remove it from core instance list.
Poll:
Wait for an event on vb2 src and vb2 dst queues.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Stefan Schmidt <stefan.schmidt@linaro.org> # x1e80100 (Dell XPS 13 9345)
Reviewed-by: Stefan Schmidt <stefan.schmidt@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
