Pull MTD updates from Miquel Raynal:
"MTD device changes:
- switch platform_driver back to remove()
- misc fixes
SPI-NAND changes:
- a load of fixes to Winbond manufacturer driver
- structure constification
Raw NAND changes:
- improve the power management of the GPMI driver
- Davinci driver clean-ups
- fix leak in the Atmel driver
- fix some typos in the core
SPI NOR changes:
- Introduce byte swap support for 8D-8D-8D mode and a user for it:
macronix.
SPI NOR flashes may swap the bytes on a 16-bit boundary when
configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the
controllers swap the bytes back at runtime. This avoids breaking
the boot sequence because of the endianness problems that appear
when the bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with
byte swap support. Along with the SPI MEM byte swap support we
queue a patch for the SPI MXIC controller that swaps the bytes back
at runtime"
* tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (25 commits)
mtd: spi-nor: core: replace dummy buswidth from addr to data
mtd: spi-nor: winbond: add "w/ and w/o SFDP" comment
mtd: spi-nor: spansion: Use nor->addr_nbytes in octal DTR mode in RD_ANY_REG_OP
mtd: Switch back to struct platform_driver::remove()
mtd: cfi_cmdset_0002: remove redundant assignment to variable ret
mtd: spinand: Constify struct nand_ecc_engine_ops
MAINTAINERS: add mailing list for GPMI NAND driver
mtd: spinand: winbond: Sort the devices
mtd: spinand: winbond: Ignore the last ID characters
mtd: spinand: winbond: Fix 512GW, 01GW, 01JW and 02JW ECC information
mtd: spinand: winbond: Fix 512GW and 02JW OOB layout
mtd: nand: raw: gpmi: improve power management handling
mtd: nand: raw: gpmi: switch to SYSTEM_SLEEP_PM_OPS
mtd: rawnand: davinci: use generic device property helpers
mtd: rawnand: davinci: break the line correctly
mtd: rawnand: davinci: order headers alphabetically
mtd: rawnand: atmel: Fix possible memory leak
mtd: rawnand: Correct multiple typos in comments
mtd: hyperbus: rpc-if: Add missing MODULE_DEVICE_TABLE
mtd: spi-nor: add support for Macronix Octal flash
...
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mtd to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007205803.444994-10-u.kleine-koenig@baylibre.com
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
The check in nand_base.c, nand_scan_tail() : has the following code:
(ecc->steps * ecc->size != mtd->writesize) which fails for some NAND chips.
Remove ECC entries in this driver which are not integral multiplications,
and adjust the number of chunks for entries which fails the above
calculation so it will calculate correctly (this was previously done
automatically before the check and was removed in a later commit).
Fixes: 68c18dae68 ("mtd: rawnand: marvell: add missing layouts")
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Pull mtd updates from Miquel Raynal:
"The main set of changes is related to Uwe's work converting platform
remove callbacks to return void. Comes next (in number of changes)
Kees' additional structures annotations to improve the sanitizers. The
usual amount of cleanups apply.
About the more substancial contribution, one main function of the
partitions core could return an error which was not checked, this is
now fixed. On the bindings side, fixed partitions can now have a
compression property. Finally, an erroneous situation is now always
avoided in the MAP RAM driver.
CFI:
- A several years old byte swap has been fixed.
NAND:
- The subsystem has, as usual, seen a bit of cleanup being done this
cycle, typically return values of platform_get_irq() and
devm_kasprintf(). There is also a better ECC check in the Arasan
driver. This comes with smaller misc changes.
- In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
SPI NOR:
- For SPI NOR we cleaned the flash info entries in order to have them
slimmer and self explanatory. In order to make the entries as slim
as possible, we introduced sane default values so that the actual
flash entries don't need to specify them. We now use a flexible
macro to specify the flash ID instead of the previous INFOx()
macros that had hardcoded ID lengths.
Instead of:
{ "w25q512nwm", INFO(0xef8020, 0, 64 * 1024, 0)
OTP_INFO(256, 3, 0x1000, 0x1000) },
We now use:
.id = SNOR_ID(0xef, 0x80, 0x20),
.name = "w25q512nwm",
.otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
- We also removed some flash entries: the very old Catalyst SPI
EEPROMs that were introduced once with the SPI-NOR subsystem, and a
Fujitsu MRAM. Both should use the at25 EEPROM driver. The latter
even has device tree bindings for the at25 driver.
- We made sure that the conversion didn't introduce any unwanted
changes by comparing the .rodata segment before and after the
conversion. The patches landed in linux-next immediately after
v6.6-rc2, we haven't seen any regressions yet.
- Apart of the autumn cleaning we introduced a new flash entry,
at25ff321a, and added block protection support for mt25qu512a"
* tag 'mtd/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (91 commits)
mtd: cfi_cmdset_0001: Byte swap OTP info
mtd: rawnand: meson: check return value of devm_kasprintf()
mtd: rawnand: intel: check return value of devm_kasprintf()
mtd: rawnand: sh_flctl: Convert to module_platform_driver()
mtd: spi-nor: micron-st: use SFDP table for mt25qu512a
mtd: spi-nor: micron-st: enable lock/unlock for mt25qu512a
mtd: rawnand: Remove unused of_gpio.h inclusion
mtd: spinand: Add support for XTX XT26xxxDxxxxx
mtd: spinand: winbond: add support for serial NAND flash
mtd: rawnand: cadence: Annotate struct cdns_nand_chip with __counted_by
mtd: rawnand: Annotate struct mtk_nfc_nand_chip with __counted_by
mtd: spinand: add support for FORESEE F35SQA002G
mtd: rawnand: rockchip: Use struct_size()
mtd: rawnand: arasan: Include ECC syndrome along with in-band data while checking for ECC failure
mtd: Use device_get_match_data()
mtd: spi-nor: nxp-spifi: Convert to platform remove callback returning void
mtd: spi-nor: hisi-sfc: Convert to platform remove callback returning void
mtd: maps: sun_uflash: Convert to platform remove callback returning void
mtd: maps: sa1100-flash: Convert to platform remove callback returning void
mtd: maps: pxa2xx-flash: Convert to platform remove callback returning void
...
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: stable@vger.kernel.org
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ravi Chandra Minnikanti <rminnikanti@marvell.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-1-miquel.raynal@bootlin.com
Raw NAND core changes:
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230714174751.4060439-1-robh@kernel.org
marvell_nfc_setup_interface() uses the frequency retrieved from the
clock associated with the nand interface to determine the timings that
will be used. By changing the NAND frequency select without reflecting
this in the clock configuration this means that the timings calculated
don't correctly meet the requirements of the NAND chip. This hasn't been
an issue up to now because of a different bug that was stopping the
timings being updated after they were initially set.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-2-chris.packham@alliedtelesis.co.nz
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
Fix merge conflict with mtd tree regarding the brcm bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221109231325.7714-1-hamish.martin@alliedtelesis.co.nz
Fix kerneldoc comments and add missing documentation for members to fix
W=1 compile warnings like:
drivers/mtd/nand/raw/marvell_nand.c:251: warning:
cannot understand function prototype: 'struct marvell_hw_ecc_layout '
drivers/mtd/nand/raw/marvell_nand.c:342: warning:
Function parameter or member 'layout' not described in 'marvell_nand_chip'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-5-krzk@kernel.org
The name/suffix data_interface is a bit misleading in that the field
or functions actually represent a configuration that can be applied by
the controller/chip. Let's rename all fields/functions/hooks that are
worth renaming.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In a previous fix, I changed the condition on which the timeout of an
IRQ is reached from:
if (!ret)
into:
if (ret && !pending)
While having a non-zero return code is usual in the Linux kernel, here
ret comes from a wait_for_completion_timeout() which returns 0 when
the waiting period is too long.
Hence, the revised condition should be:
if (!ret && !pending)
The faulty patch did not produce any error because of the !pending
condition so this change is finally purely cosmetic and does not
change the actual driver behavior.
Fixes: cafb56dd74 ("mtd: rawnand: marvell: prevent timeouts on a loaded machine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200424164501.26719-2-miquel.raynal@bootlin.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200226222722.GA18020@embeddedor
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
Since the migration of the driver to stop using the legacy
->select_chip() hook, there is nothing deselecting the target anymore,
thus the selection is not forced at the next access. Ensure the ND_RUN
bit and the interrupts are always in a clean state.
Cc: Daniel Mack <daniel@zonque.org>
Cc: stable@vger.kernel.org
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since the migration of the driver to stop using the legacy
->select_chip() hook, the marvell_nfc_select_chip() helper has been
'renamed' to marvell_nfc_select_target(). Update a left-over reference
to this helper in a comment in the ->resume() path.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
We plan to move cache related fields to a pagecache struct in nand_chip
but some drivers access ->pagebuf directly to invalidate the cache
before they start using ->data_buf.
Let's provide an helper that returns a pointer to ->data_buf after
invalidating the cache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
