This is a preparation patch for the introduction of CAN XL.
CAN FD and CAN XL uses similar bittiming parameters. Add one level of
nesting for all the CAN FD parameters. Typically:
priv->can.data_bittiming;
becomes:
priv->can.fd.data_bittiming;
This way, the CAN XL equivalent (to be introduced later) would be:
priv->can.xl.data_bittiming;
Add the new struct data_bittiming_params which contains all the data
bittiming parameters, including the TDC and the callback functions.
This done, update all the CAN FD drivers to make use of the new
layout.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250501171213.2161572-2-mailhol.vincent@wanadoo.fr
[mkl: fix rcar_canfd]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-01-10
Pierre-Henry Moussay adds PIC64GX compatibility to the DT bindings for
Microchip's mpfs-can IP core.
The next 3 patches are by Sean Nyekjaer and target the tcan4x5x
driver. First the DT bindings is converted to DT schema, then nWKRQ
voltage selection is added to the driver.
Dario Binacchi's patch for the sun4i_can makes the driver more
consistent by adding a likely() to the driver.
Another patch by Sean Nyekjaer for the tcan4x5x driver gets rid of a
false error message.
Charan Pedumuru converts the atmel-can DT bindings to DT schema.
The next 2 patches are by Oliver Hartkopp. The first one maps Oliver's
former mail addresses to a dedicated CAN mail address. The second one
assigns net/sched/em_canid.c additionally to the CAN maintainers.
Ariel Otilibili's patch removes dead code from the CAN dev helper.
The next 3 patches are by Sean Nyekjaer and add HW standby support to
the tcan4x5x driver.
A patch by Dario Binacchi fixes the DT bindings for the st,stm32-bxcan
driver.
The last 4 patches are by Jimmy Assarsson and target the kvaser_usb
and the kvaser_pciefd driver: error statistics are improved and
CAN_CTRLMODE_BERR_REPORTING is added.
* tag 'linux-can-next-for-6.14-20250110' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: kvaser_pciefd: Add support for CAN_CTRLMODE_BERR_REPORTING
can: kvaser_pciefd: Update stats and state even if alloc_can_err_skb() fails
can: kvaser_usb: Add support for CAN_CTRLMODE_BERR_REPORTING
can: kvaser_usb: Update stats and state even if alloc_can_err_skb() fails
dt-bindings: can: st,stm32-bxcan: fix st,gcan property type
can: m_can: call deinit/init callback when going into suspend/resume
can: tcan4x5x: add deinit callback to set standby mode
can: m_can: add deinit callback
can: dev: can_get_state_str(): Remove dead code
MAINTAINERS: assign em_canid.c additionally to CAN maintainers
mailmap: add an entry for Oliver Hartkopp
dt-bindings: net: can: atmel: Convert to json schema
can: tcan4x5x: get rid of false clock errors
can: sun4i_can: continue to use likely() to check skb
can: tcan4x5x: add option for selecting nWKRQ voltage
dt-bindings: can: tcan4x5x: Document the ti,nwkrq-voltage-vio option
dt-bindings: can: convert tcan4x5x.txt to DT schema
dt-bindings: can: mpfs: add PIC64GX CAN compatibility
====================
Link: https://patch.msgid.link/20250110112712.3214173-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In commit 6e86a1543c ("can: dev: provide optional GPIO based
termination support") GPIO based termination support was added.
For no particular reason that patch uses gpiod_set_value() to set the
GPIO. This leads to the following warning, if the systems uses a
sleeping GPIO, i.e. behind an I2C port expander:
| WARNING: CPU: 0 PID: 379 at /drivers/gpio/gpiolib.c:3496 gpiod_set_value+0x50/0x6c
| CPU: 0 UID: 0 PID: 379 Comm: ip Not tainted 6.11.0-20241016-1 #1 823affae360cc91126e4d316d7a614a8bf86236c
Replace gpiod_set_value() by gpiod_set_value_cansleep() to allow the
use of sleeping GPIOs.
Cc: Nicolai Buchwitz <nb@tipi-net.de>
Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reported-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Tested-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Fixes: 6e86a1543c ("can: dev: provide optional GPIO based termination support")
Link: https://patch.msgid.link/20241121-dev-fix-can_set_termination-v1-1-41fa6e29216d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some CAN controllers do not have a register that contains the current
CAN state, but only a register that contains the error counters.
Introduce a new function can_state_get_by_berr_counter() that returns
the current TX and RX state depending on the provided CAN bit error
counters.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-1-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This race condition was discovered while updating the at91_can driver
to use can_bus_off(). The following scenario describes how the
converted at91_can driver would behave.
When a CAN device goes into BUS-OFF state, the driver usually
stops/resets the CAN device and calls can_bus_off().
This function sets the netif carrier to off, and (if configured by
user space) schedules a delayed work that calls can_restart() to
restart the CAN device.
The can_restart() function first checks if the carrier is off and
triggers an error message if the carrier is OK.
Then it calls the driver's do_set_mode() function to restart the
device, then it sets the netif carrier to on. There is a race window
between these two calls.
The at91 CAN controller (observed on the sama5d3, a single core 32 bit
ARM CPU) has a hardware limitation. If the device goes into bus-off
while sending a CAN frame, there is no way to abort the sending of
this frame. After the controller is enabled again, another attempt is
made to send it.
If the bus is still faulty, the device immediately goes back to the
bus-off state. The driver calls can_bus_off(), the netif carrier is
switched off and another can_restart is scheduled. This occurs within
the race window before the original can_restart() handler marks the
netif carrier as OK. This would cause the 2nd can_restart() to be
called with an OK netif carrier, resulting in an error message.
The flow of the 1st can_restart() looks like this:
can_restart()
// bail out if netif_carrier is OK
netif_carrier_ok(dev)
priv->do_set_mode(dev, CAN_MODE_START)
// enable CAN controller
// sama5d3 restarts sending old message
// CAN devices goes into BUS_OFF, triggers IRQ
// IRQ handler start
at91_irq()
at91_irq_err_line()
can_bus_off()
netif_carrier_off()
schedule_delayed_work()
// IRQ handler end
netif_carrier_on()
The 2nd can_restart() will be called with an OK netif carrier and the
error message will be printed.
To close the race window, first set the netif carrier to on, then
restart the controller. In case the restart fails with an error code,
roll back the netif carrier to off.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-2-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During testing, I triggered a can_restart() with the netif carrier
being OK [1]. The BUG_ON, which checks if the carrier is OK, results
in a fatal kernel crash. This is neither helpful for debugging nor for
a production system.
[1] The root cause is a race condition in can_restart() which will be
fixed in the next patch.
Do not crash the kernel, issue an error message instead, and continue
restarting the CAN device anyway.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-1-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Implement the function can_bittiming_const_valid() to check the
validity of the specified bit timing constant. Call this function from
register_candev() to check the bit timing constants during the
registration of the CAN interface.
Link: https://lore.kernel.org/all/20230202110854.2318594-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add function can_ethtool_op_get_ts_info_hwts(). This function will be
used by CAN devices with hardware TX/RX timestamping support to
implement ethtool_ops::get_ts_info. This function does not offer
support to activate/deactivate hardware timestamps at device level nor
support the filter options (which is currently the case for all CAN
devices with hardware timestamping support).
The fact that hardware timestamp can not be deactivated at hardware
level does not impact the userland. As long as the user do not set
SO_TIMESTAMPING using a setsockopt() or ioctl(), the kernel will not
emit TX timestamps (RX timestamps will still be reproted as it is the
case currently).
Drivers which need more fine grained control remains free to implement
their own function, but we foresee that the generic function
introduced here will be sufficient for the majority.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220727101641.198847-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the next patches, the software/virtual drivers (slcan, v(x)can)
will depend on drivers/net/can/dev/skb.o.
This patch changes the scope of the can-dev module to include the
above mentioned drivers.
To do so, we reuse the menu "CAN Device Drivers" and turn it into a
configmenu using the config symbol CAN_DEV (which we released in
previous patch). Also, add a description to this new CAN_DEV
menuconfig.
The symbol CAN_DEV now only triggers the build of skb.o. For this
reasons, all the macros from linux/module.h are deported from
drivers/net/can/dev/dev.c to drivers/net/can/dev/skb.c.
Finally, drivers/net/can/dev/Makefile is adjusted accordingly.
Link: https://lore.kernel.org/all/20220610143009.323579-3-mailhol.vincent@wanadoo.fr
Suggested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Max Staudt <max@enpas.org>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The statically enabled features of a CAN controller can be retrieved
using below formula:
| u32 ctrlmode_static = priv->ctrlmode & ~priv->ctrlmode_supported;
As such, there is no need to store this information. This patch remove
the field ctrlmode_static of struct can_priv and provides, in
replacement, the inline function can_get_static_ctrlmode() which
returns the same value.
Link: https://lore.kernel.org/all/20211213160226.56219-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For CAN buses to work, a termination resistor has to be present at both
ends of the bus. This resistor is usually 120 Ohms, other values may be
required for special bus topologies.
This patch adds support for a generic GPIO based CAN termination. The
resistor value has to be specified via device tree, and it can only be
attached to or detached from the bus. By default the termination is not
active.
Link: https://lore.kernel.org/r/20210818071232.20585-4-o.rempel@pengutronix.de
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since 20dd3850bc ("can: Speed up CAN frame receiption by using
ml_priv") the CAN framework uses per device specific data in the AF_CAN
protocol. For this purpose the struct net_device->ml_priv is used. Later
the ml_priv usage in CAN was extended for other users, one of them being
CAN_J1939.
Later in the kernel ml_priv was converted to an union, used by other
drivers. E.g. the tun driver started storing it's stats pointer.
Since tun devices can claim to be a CAN device, CAN specific protocols
will wrongly interpret this pointer, which will cause system crashes.
Mostly this issue is visible in the CAN_J1939 stack.
To fix this issue, we request a dedicated CAN pointer within the
net_device struct.
Reported-by: syzbot+5138c4dd15a0401bec7b@syzkaller.appspotmail.com
Fixes: 20dd3850bc ("can: Speed up CAN frame receiption by using ml_priv")
Fixes: ffd956eef6 ("can: introduce CAN midlayer private and allocate it automatically")
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Fixes: 497a5757ce ("tun: switch to net core provided statistics counters")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210223070127.4538-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
