np->name was being used after calling of_node_put(np), which
releases the node and can lead to a use-after-free bug.
Previously, of_node_put(np) was called unconditionally after
of_find_device_by_node(np), which could result in a use-after-free if
pdev is NULL.
This patch moves of_node_put(np) after the error check to ensure
the node is only released after both the error and success cases
are handled appropriately, preventing potential resource issues.
Fixes: 23290c7bc1 ("net: airoha: Introduce Airoha NPU support")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250715143102.3458286-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the newly added of_reserved_mem_region_to_resource{_byname}()
functions to handle "memory-region" properties.
The error handling is a bit different for mtk_wed_mcu_load_firmware().
A failed match of the "memory-region-names" would skip the entry, but
then other errors in the lookup and retrieval of the address would not
skip the entry. However, that distinction is not really important.
Either the region is available and usable or it is not. So now, errors
from of_reserved_mem_region_to_resource() are ignored so the region is
simply skipped.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250703183459.2074381-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
EN7581 SoC allows configuring the size and the number of buffers in
hwfd payload queue for both QDMA0 and QDMA1.
In order to reduce the required DRAM used for hwfd buffers queues and
decrease the memory footprint, differentiate hwfd buffer size for QDMA0
and QDMA1 and reduce hwfd buffer size to 1KB for QDMA1 (WAN) while
maintaining 2KB for QDMA0 (LAN).
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250619-airoha-hw-num-desc-v4-2-49600a9b319a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ib2 and airoha_foe_mac_info_common have not the same offsets in
airoha_foe_bridge and airoha_foe_ipv6 structures. Current codebase does
not accelerate IPv6 traffic in bridge mode since ib2 and l2 info are not
set properly copying airoha_foe_bridge struct into airoha_foe_ipv6 one
in airoha_ppe_foe_commit_subflow_entry routine.
Fix IPv6 hw acceleration in bridge mode resolving ib2 and
airoha_foe_mac_info_common overwrite in
airoha_ppe_foe_commit_subflow_entry() and configuring them with proper
values.
Fixes: cd53f62261 ("net: airoha: Add L2 hw acceleration support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250602-airoha-flowtable-ipv6-fix-v2-2-3287f8b55214@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
UPDMEM source-mac table is a key-value map used to store devices mac
addresses according to the port identifier. UPDMEM source mac table is
used during IPv6 traffic hw acceleration since PPE entries, for space
constraints, do not contain the full source mac address but just the
identifier in the UPDMEM source-mac table.
Configure UPDMEM source-mac table with device mac addresses and set
the source-mac ID field for PPE IPv6 entries in order to select the
proper device mac address as source mac for L3 IPv6 hw accelerated traffic.
Fixes: 00a7678310 ("net: airoha: Introduce flowtable offload support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250602-airoha-flowtable-ipv6-fix-v2-1-3287f8b55214@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Do not recycle the page twice in airoha_qdma_rx_process routine in case
of error. Just run dev_kfree_skb() if the skb has been allocated and marked
for recycling. Run page_pool_put_full_page() directly if the skb has not
been allocated yet.
Moreover, rely on DMA address from queue entry element instead of reading
it from the DMA descriptor for DMA syncing in airoha_qdma_rx_process().
Fixes: e12182ddb6 ("net: airoha: Enable Rx Scatter-Gather")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250515-airoha-fix-rx-process-error-condition-v2-1-657e92c894b9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The official Airoha EN7581 firmware requires adding max_packet field in
ppe_mbox_data struct while the unofficial one used to develop the Airoha
EN7581 flowtable support does not require this field.
This patch does not introduce any real backwards compatible issue since
EN7581 fw is not publicly available in linux-firmware or other
repositories (e.g. OpenWrt) yet and the official fw version will use this
new layout. For this reason this change needs to be backported.
Moreover, make explicit the padding added by the compiler introducing
the rsv array in init_info struct.
At the same time use u32 instead of int for init_info and set_info
struct definitions in ppe_mbox_data struct.
Fixes: 23290c7bc1 ("net: airoha: Introduce Airoha NPU support")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250506-airoha-en7581-fix-ppe_mbox_data-v5-1-29cabed6864d@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
EN7581 ethernet SoC supports 4 programmable IRQ lines each one composed
by 4 IRQ configuration registers. Add airoha_irq_bank struct as a
container for independent IRQ lines info (e.g. IRQ number, enabled source
interrupts, ecc). This is a preliminary patch to support multiple IRQ lines
in airoha_eth driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250418-airoha-eth-multi-irq-v1-1-1ab0083ca3c1@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce tc matchall filter offload support in airoha_eth driver.
Matchall hw filter is used to implement hw rate policing via tc action
police:
$tc qdisc add dev eth0 handle ffff: ingress
$tc filter add dev eth0 parent ffff: matchall action police \
rate 100mbit burst 1000k drop
The current implementation supports just drop/accept as exceed/notexceed
actions. Moreover, rate and burst are the only supported configuration
parameters.
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250415-airoha-hw-rx-ratelimit-v4-1-03458784fbc3@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Dev pointer in airoha_ppe_foe_entry_prepare routine is not strictly
a device allocated by airoha_eth driver since it is an egress device
and the flowtable can contain even wlan, pppoe or vlan devices. E.g:
flowtable ft {
hook ingress priority filter
devices = { eth1, lan1, lan2, lan3, lan4, wlan0 }
flags offload ^
|
"not allocated by airoha_eth" --
}
In this case airoha_get_dsa_port() will just return the original device
pointer and we can't assume netdev priv pointer points to an
airoha_gdm_port struct.
Fix the issue validating egress gdm port in airoha_ppe_foe_entry_prepare
routine before accessing net_device priv pointer.
Fixes: 00a7678310 ("net: airoha: Introduce flowtable offload support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250401-airoha-validate-egress-gdm-port-v4-1-c7315d33ce10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ETS Qdisc schedules SP bands in a priority order assigning band-0 the
highest priority (band-0 > band-1 > .. > band-n) while EN7581 arranges
SP bands in a priority order assigning band-7 the highest priority
(band-7 > band-6, .. > band-n).
Fix priomap check in airoha_qdma_set_tx_ets_sched routine in order to
align ETS Qdisc and airoha_eth driver SP priority ordering.
Fixes: b56e4d660a ("net: airoha: Enforce ETS Qdisc priomap")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Link: https://patch.msgid.link/20250331-airoha-ets-validate-priomap-v1-1-60a524488672@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The #if check causes a build failure when CONFIG_DEBUG_FS is turned
off:
In file included from drivers/net/ethernet/airoha/airoha_eth.c:17:
drivers/net/ethernet/airoha/airoha_eth.h:543:5: error: "CONFIG_DEBUG_FS" is not defined, evaluates to 0 [-Werror=undef]
543 | #if CONFIG_DEBUG_FS
| ^~~~~~~~~~~~~~~
Replace it with the correct #ifdef.
Fixes: 3fe15c640f ("net: airoha: Introduce PPE debugfs support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250314155009.4114308-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Similar to PPE support for Mediatek devices, introduce PPE debugfs
in order to dump binded and unbinded flows.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Enable hw redirection for traffic received on GDM2 port to GDM{3,4}.
This is required to apply Qdisc offloading (HTB or ETS) for traffic to
and from GDM{3,4} port.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce netfilter flowtable integration in order to allow airoha_eth
driver to offload 5-tuple flower rules learned by the PPE module if the
user accelerates them using a nft configuration similar to the one reported
below:
table inet filter {
flowtable ft {
hook ingress priority filter
devices = { lan1, lan2, lan3, lan4, eth1 }
flags offload;
}
chain forward {
type filter hook forward priority filter; policy accept;
meta l4proto { tcp, udp } flow add @ft
}
}
Tested-by: Sayantan Nandy <sayantan.nandy@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Packet Processor Engine (PPE) module available on EN7581 SoC populates
the PPE table with 5-tuples flower rules learned from traffic forwarded
between the GDM ports connected to the Packet Switch Engine (PSE) module.
The airoha_eth driver can enable hw acceleration of learned 5-tuples
rules if the user configure them in netfilter flowtable (netfilter
flowtable support will be added with subsequent patches).
airoha_eth driver configures and collects data from the PPE module via a
Network Processor Unit (NPU) RISC-V module available on the EN7581 SoC.
Introduce basic support for Airoha NPU module.
Tested-by: Sayantan Nandy <sayantan.nandy@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename airoha_set_gdm_port() in airoha_set_vip_for_gdm_port().
Get rid of airoha_set_gdm_ports routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
