With large values of CONFIG_NR_CPUS, three Intel ethernet drivers fail to
compile like:
In function ‘i40e_free_q_vector’,
inlined from ‘i40e_vsi_alloc_q_vectors’ at drivers/net/ethernet/intel/i40e/i40e_main.c:12112:3:
571 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
include/linux/rcupdate.h:1084:17: note: in expansion of macro ‘BUILD_BUG_ON’
1084 | BUILD_BUG_ON(offsetof(typeof(*(ptr)), rhf) >= 4096); \
drivers/net/ethernet/intel/i40e/i40e_main.c:5113:9: note: in expansion of macro ‘kfree_rcu’
5113 | kfree_rcu(q_vector, rcu);
| ^~~~~~~~~
The problem is that the 'rcu' member in 'q_vector' is too far from the start
of the structure. Move this member before the CPU mask instead, in all three
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add Tx Hang detection due to an unhandled MDD Event.
Previously, a malicious VF could disable the entire port causing
TX to hang on the E610 card.
Those events that caused PF to freeze were not detected
as an MDD event and usually required a Tx Hang watchdog timer
to catch the suspension, and perform a physical function reset.
Implement flows in the affected PF driver in such a way to check
the cause of the hang, detect it as an MDD event and log an
entry of the malicious VF that caused the Hang.
The PF blocks the malicious VF, if it continues to be the source
of several MDD events.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add malicious driver detection to ixgbe driver. The supported devices
are E610 and X550.
Handling MDD events is enabled while VFs are created and turned off
when they are disabled. There is no runtime command to enable or
disable MDD independently.
MDD event is logged when malicious VF driver is detected. For example VF
can try to send incorrect Tx descriptor (TSO on, but length field not
correct). It can be reproduced by manipulating the driver, or using
driver with incorrect descriptor values.
Example log:
"Malicious event on VF 0 tx:128 rx:128"
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
New timestamping API was introduced in commit 66f7223039 ("net: add
NDOs for configuring hardware timestamping") from kernel v6.6.
It is time to convert the Intel ixgbe driver to the new API, so that
timestamping configuration can be removed from the ndo_eth_ioctl() path
completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Corrected spelling errors such as "simular" -> "similar",
"excepted" -> "accepted", and "Determime" -> "Determine".
Fixed including incorrect word usage ("to MAC" -> "two MAC")
and improved awkward phrasing.
Aligned function header descriptions with their actual functionality
(e.g., "Writes a value" -> "Reads a value").
Corrected typo in error code from -ENIVAL to -EINVAL.
Improved overall clarity and consistency in comment across various
functions.
These changes improve maintainability and readability of the code
without affecting functionality.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce a link_down_events counter to the ixgbe driver, incremented
each time the link transitions from up to down.
This counter can help diagnose issues related to link stability,
such as port flapping or unexpected link drops.
The value is exposed via ethtool's get_link_ext_stats() interface.
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Steffen Klassert says:
====================
1) Remove some unnecessary strscpy_pad() size arguments.
From Thorsten Blum.
2) Correct use of xso.real_dev on bonding offloads.
Patchset from Cosmin Ratiu.
3) Add hardware offload configuration to XFRM_MSG_MIGRATE.
From Chiachang Wang.
4) Refactor migration setup during cloning. This was
done after the clone was created. Now it is done
in the cloning function itself.
From Chiachang Wang.
5) Validate assignment of maximal possible SEQ number.
Prevent from setting to the maximum sequrnce number
as this would cause for traffic drop.
From Leon Romanovsky.
6) Prevent configuration of interface index when offload
is used. Hardware can't handle this case.i
From Leon Romanovsky.
7) Always use kfree_sensitive() for SA secret zeroization.
From Zilin Guan.
ipsec-next-2025-05-23
* tag 'ipsec-next-2025-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: use kfree_sensitive() for SA secret zeroization
xfrm: prevent configuration of interface index when offload is used
xfrm: validate assignment of maximal possible SEQ number
xfrm: Refactor migration setup during the cloning process
xfrm: Migrate offload configuration
bonding: Fix multiple long standing offload races
bonding: Mark active offloaded xfrm_states
xfrm: Add explicit dev to .xdo_dev_state_{add,delete,free}
xfrm: Remove unneeded device check from validate_xmit_xfrm
xfrm: Use xdo.dev instead of xdo.real_dev
net/mlx5: Avoid using xso.real_dev unnecessarily
xfrm: Remove unnecessary strscpy_pad() size arguments
====================
Link: https://patch.msgid.link/20250523075611.3723340-1-steffen.klassert@secunet.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Provide support for the following devlink cmds:
-DEVLINK_CMD_REGION_GET
-DEVLINK_CMD_REGION_NEW
-DEVLINK_CMD_REGION_DEL
-DEVLINK_CMD_REGION_READ
ixgbe devlink region implementation, similarly to the ice one,
lets user to create snapshots of content of Non Volatile Memory,
content of Shadow RAM, and capabilities of the device.
For both NVM and SRAM regions provide .read() handler to let user
read their contents without the need to create full snapshots.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently only APM (Advanced Power Management) is supported by
the ixgbe driver. It works for magic packets only, as for different
sources of wake-up E610 adapter utilizes different feature.
Add E610 specific implementation of ixgbe_set_wol() callback. When
any of broadcast/multicast/unicast wake-up is set, disable APM and
configure ACPI (Advanced Configuration and Power Interface).
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
E610's implementation of various ethtool ops is different than
the ones corresponding to ixgbe legacy products. Therefore create
separate E610 ethtool_ops struct which will be filled out in the
forthcoming patches.
Add adequate ops struct basing on MAC type. This step requires
changing a bit the flow of probing by placing ixgbe_set_ethtool_ops
after hw.mac.type is assigned. So move the whole netdev assignment
block after hw.mac.type is known. This step doesn't have any additional
impact on probing sequence.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously, device driver IPSec offload implementations would fall into
two categories:
1. Those that used xso.dev to determine the offload device.
2. Those that used xso.real_dev to determine the offload device.
The first category didn't work with bonding while the second did.
In a non-bonding setup the two pointers are the same.
This commit adds explicit pointers for the offload netdevice to
.xdo_dev_state_add() / .xdo_dev_state_delete() / .xdo_dev_state_free()
which eliminates the confusion and allows drivers from the first
category to work with bonding.
xso.real_dev now becomes a private pointer managed by the bonding
driver.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The driver should detect whether the device entered FW rollback
mode and then notify user with the dedicated message including
FW and NVM versions.
Even if the driver detected rollback mode, this should not result
in an probe error and the normal flow proceeds.
FW tries to rollback to "old" operational FW located in the
inactive NVM bank in cases when newly loaded FW exhibits faulty
behavior. If something goes wrong during boot the FW may switch
into rollback mode in an attempt to avoid recovery mode and stay
operational. After rollback is successful, the banks are swapped,
and the "rollback" bank becomes the active bank for the next reset.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add E610 implementation of fw_recovery_mode MAC operation.
In case of E610 information about recovery mode is obtained
from FW_MODES field in IXGBE_GL_MNG_FWSM register (0x000B6134).
Introduce recovery specific probing flow and init only
vital features.
User should be able to perform NVM update using devlink
once FW error is detected in order to load a healthy img.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add E610 specific function checking whether the FW API version
is compatible with the driver expectations.
The major API version should be less than or equal to the expected
API version. If not the driver won't be fully operational.
Check the minor version, and if it is more than two versions lesser
or greater than the expected version, print a message indicating
that the NVM or driver should be updated respectively.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The E610 adapters contain an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the pldmfw library to implement device flash update for
the Intel ixgbe networking device driver specifically for E610 devices.
This support uses the devlink flash update interface.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset.
With this implementation, basic flash update for the E610 hardware is
supported.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add functions reading inactive versions from the inactive flash
bank.
Print stored versions for the content present in the inactive bank.
If there's pending update the versions reflect the ones which
are going to be loaded after reload. If there's no pending update
both running and stored are the same, which means there won't
be any NVM change on reload.
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce 2 E610 specific callbacks implementations:
-ixgbe_start_hw_e610() which expands the regular .start_hw callback with
getting FW version information
-ixgbe_read_pba_string_e610() which gets Product Board Assembly string
Extend EEPROM ops with new .read_pba_string in order to distinguish
generic one and the E610 one.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
E610 devices give possibility to show more detailed info than the previous
boards.
Extend reporting NVM info with following pieces:
fw.mgmt.api -> version number of the API
fw.mgmt.build -> identifier of the source for the FW
fw.mgmt.srev -> number defining FW's security revision
fw.psid.api -> version defining the format of the flash contents
fw.undi.srev -> number defining OROM's security revision
fw.netlist -> version of the netlist module
fw.netlist.build -> first 4 bytes of the netlist hash
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provide devlink .info_get() callback implementation to allow the
driver to report detailed version information. The following info
is reported:
"serial_number" -> The PCI DSN of the adapter
"fw.bundle_id" -> Unique identifier for the combined flash image
"fw.undi" -> Version of the Option ROM containing the UEFI driver
"board.id" -> The PBA ID string
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add an initial support for devlink interface to ixgbe driver.
Similarly to i40e driver the implementation doesn't enable
devlink to manage device-wide configuration. Devlink instance
is created for each physical function of PCIe device.
Create separate directory for devlink related ixgbe files
and use naming scheme similar to the one used in the ice driver.
Add a stub for Documentation, to be extended by further patches.
Change struct ixgbe_adapter allocation to be done by devlink (Przemek),
as suggested by Jiri.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Co-developed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Wrap use of netdev_priv() in order to change the allocator of the device
private structure from alloc_etherdev_mq() to the devlink in next commit.
All but one netdev_priv() calls in the whole driver are replaced, the
remaining one is called on MACVLAN (so not ixgbe) device.
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current implementation of `ixgbe_write_i2c_combined_generic_int` and
`ixgbe_write_i2c_byte_generic_int` sets `max_retry` to `1`, which makes
the condition `retry < max_retry` always evaluate to `false`. This renders
the retry mechanism ineffective, as the debug message and retry logic are
never executed.
This patch increases `max_retry` to `3` in both functions, aligning them
with the retry logic in `ixgbe_read_i2c_combined_generic_int`. This
ensures that the retry mechanism functions as intended, improving
robustness in case of I2C write failures.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The commit 23c0e5a16b ("ixgbe: Add link management support for E610
device") introduced incorrect media type detection for E610 device. It
reproduces when advertised speed is modified after driver reload. Clear
the previous outdated PHY type high value.
Reproduction steps:
modprobe ixgbe
ethtool -s eth0 advertise 0x1000000000000
modprobe -r ixgbe
modprobe ixgbe
ethtool -s eth0 advertise 0x1000000000000
Result before the fix:
netlink error: link settings update failed
netlink error: Invalid argument
Result after the fix:
No output error
Fixes: 23c0e5a16b ("ixgbe: Add link management support for E610 device")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2025-03-24
1) Prevent setting high order sequence number bits input in
non-ESN mode. From Leon Romanovsky.
2) Support PMTU handling in tunnel mode for packet offload.
From Leon Romanovsky.
3) Make xfrm_state_lookup_byaddr lockless.
From Florian Westphal.
4) Remove unnecessary NULL check in xfrm_lookup_with_ifid().
From Dan Carpenter.
* tag 'ipsec-next-2025-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: Remove unnecessary NULL check in xfrm_lookup_with_ifid()
xfrm: state: make xfrm_state_lookup_byaddr lockless
xfrm: check for PMTU in tunnel mode for packet offload
xfrm: provide common xdo_dev_offload_ok callback implementation
xfrm: rely on XFRM offload
xfrm: simplify SA initialization routine
xfrm: delay initialization of offload path till its actually requested
xfrm: prevent high SEQ input in non-ESN mode
====================
Link: https://patch.msgid.link/20250324061855.4116819-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
E610 NICs unlike the previous devices utilising ixgbe driver
are notified in the case of overheating by the FW ACI event.
In event of overheat when threshold is exceeded, FW suspends all
traffic and sends overtemp event to the driver. Then driver
logs appropriate message and disables the adapter instance.
The card remains in that state until the platform is rebooted.
This approach is a solution to the fact current version of the
E610 FW doesn't support reading thermal sensor data by the
SW. So give to user at least any info that overtemp event
has occurred, without interface disappearing from the OS
without any note.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Jeremiah Lokan <jeremiahx.j.lokan@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250310174502.3708121-7-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Almost all drivers except bond and nsim had same check if device
can perform XFRM offload on that specific packet. The check was that
packet doesn't have IPv4 options and IPv6 extensions.
In NIC drivers, the IPv4 HELEN comparison was slightly different, but
the intent was to check for the same conditions. So let's chose more
strict variant as a common base.
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
