When connected to an AP, the PHY will typically be tuned to
a higher bandwidth than the beacons are transmitted on, as
they are normally only transmitted on 20 MHz. This can mean
that another STA is simultaneously transmitting on another
channel of the higher bandwidth, and apparently this energy
may be taken into account by the PHY, resulting in elevated
energy readings.
To work around this, track the firmware's corrected beacon
energy data and replace the RSSI in beacons by that. The
replacement happens for all beacons received in the context
of the current MAC or link (depending on FW version), in
which case the filters will drop all else. For a scan, which
is only tuning to 20 MHz channels, the MAC/link ID will be
one that isn't found (the AUX ID 4), and no correction will
be done (nor is it needed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250711183056.324bfe7027ff.I160f947e7aab30e0110a7019ed46186e57c3de14@changeid
In the current code, if there was a rekey, we remove all the existing keys
from mac80211, then re-add the ones that the FW sent with
ieee80211_gtk_rekey_add, (newer FW will send also the existing GTKs/BIGTKs)
and then update the sequence number.
Instead of removing and re-adding the existing keys for no good reason,
we can just update the sequence of all keys, also of the ones that are
going to be replaced, and update again after the replace.
This change is required because ieee80211_gtk_rekey_add is going to be
changed to lookup the cipher from the old key instead of receiving it as an
argument, and for this it will need the old key(s), so we can't remove all
keys.
Note that with this change, in case that a key that existed before wowlan
is replaced, mac80211 will now call the driver to remove the old key and
add the new one (as opposed the previous behaviour, in which the key was
removed by the driver itself).
Of course we don't want to run the set_key callbacks in this case, so just
return early.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250710212632.f0b5e19f77f5.I958f4926f168cdad6d4d7720ebde2f5e812b297d@changeid
Miri Korenblit says:
====================
iwlwifi-next - iwlwifi features
Mostly cleanups. A few fixes and small features.
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a requirement to exit EMLSR if there wasn't enough throughput
in the secondary link.
This is checked in check_tpt_wk, which runs every 5 seconds in a high
throughput scenario (when the throughput blocker isn't set)
It can happen that this worker is running immediately after we entered
EMLSR, and in that case the secondary link didn't have a chance to have
throughput. In that case we will exit EMLSR for no good reason.
Fix this by tracking the time we entered EMLSR, and in the worker make
sure that 5 seconds passed from when we entered EMLSR. If not, don't
check the secondary link throughput.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250612144708.c680f8d7dc37.I8a02d1e8d99df3789da8d5714f19b31a865a61ff@changeid
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The initialization of async_handlers_list
was accidentally removed in a previous change.
Then it was restoted by commit 175e69e33c ("wifi: iwlwifi: restore
missing initialization of async_handlers_list").
Somehow, the initialization disappeared again.
Restote it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Pull networking fixes from Jakub Kicinski:
"Including fixes from CAN, wireless, Bluetooth, and Netfilter.
Current release - regressions:
- Revert "kunit: configs: Enable CONFIG_INIT_STACK_ALL_PATTERN in
all_tests", makes kunit error out if compiler is old
- wifi: iwlwifi: mvm: fix assert on suspend
- rxrpc: fix return from none_validate_challenge()
Current release - new code bugs:
- ovpn: couple of fixes for socket cleanup and UDP-tunnel teardown
- can: kvaser_pciefd: refine error prone echo_skb_max handling logic
- fix net_devmem_bind_dmabuf() stub when DEVMEM not compiled
- eth: airoha: fixes for config / accel in bridge mode
Previous releases - regressions:
- Bluetooth: hci_qca: move the SoC type check to the right place, fix
GPIO integration
- prevent a NULL deref in rtnl_create_link() after locking changes
- fix udp gso skb_segment after pull from frag_list
- hv_netvsc: fix potential deadlock in netvsc_vf_setxdp()
Previous releases - always broken:
- netfilter:
- nf_nat: also check reverse tuple to obtain clashing entry
- nf_set_pipapo_avx2: fix initial map fill (zeroing)
- fix the helper for incremental update of packet checksums after
modifying the IP address, used by ILA and BPF
- eth:
- stmmac: prevent div by 0 when clock rate is misconfigured
- ice: fix Tx scheduler handling of XDP and changing queue count
- eth: fix support for the RGMII interface when delays configured"
* tag 'net-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
calipso: unlock rcu before returning -EAFNOSUPPORT
seg6: Fix validation of nexthop addresses
net: prevent a NULL deref in rtnl_create_link()
net: annotate data-races around cleanup_net_task
selftests: drv-net: tso: make bkg() wait for socat to quit
selftests: drv-net: tso: fix the GRE device name
selftests: drv-net: add configs for the TSO test
wireguard: device: enable threaded NAPI
netlink: specs: rt-link: decode ip6gre
netlink: specs: rt-link: add missing byte-order properties
net: wwan: mhi_wwan_mbim: use correct mux_id for multiplexing
wifi: cfg80211/mac80211: correctly parse S1G beacon optional elements
net: dsa: b53: do not touch DLL_IQQD on bcm53115
net: dsa: b53: allow RGMII for bcm63xx RGMII ports
net: dsa: b53: do not configure bcm63xx's IMP port interface
net: dsa: b53: do not enable RGMII delay on bcm63xx
net: dsa: b53: do not enable EEE on bcm63xx
net: ti: icssg-prueth: Fix swapped TX stats for MII interfaces.
selftests: netfilter: nft_nat.sh: add test for reverse clash with nat
netfilter: nf_nat: also check reverse tuple to obtain clashing entry
...
The regulatory domain information was initialized every time the
FW was loaded and the device was restarted. This was unnecessary
and useless as at this stage the wiphy channels information was
not setup yet so while the regulatory domain was set to the wiphy,
the channel information was not updated.
In case that a specific MCC was configured during FW initialization
then following updates with this MCC are ignored, and thus the
wiphy channels information is left with information not matching
the regulatory domain.
This commit moves the regulatory domain initialization to after the
operational firmware is started, i.e., after the wiphy channels were
configured and the regulatory information is needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250604061200.f138a7382093.I2fd8b3e99be13c2687da483e2cb1311ffb4fbfce@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
In case of an error during init, in_hw_restart will be set, but it will
never get cleared.
Instead, we will retry to init again, and then we will act like we are in a
restart when we are actually not.
This causes (among others) to a NULL pointer dereference when canceling
rx_omi::finished_work, that was not even initialized, because we thought
that we are in hw_restart.
Set in_hw_restart to true only if the fw is running, then we know that
FW was loaded successfully and we are not going to the retry loop.
Fixes: 7391b2a4f7 ("wifi: iwlwifi: rework firmware error handling")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250604061200.e0040e0a4b09.Iae469a0abe6bfa3c26d8a88c066bad75c2e8f121@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Pull hardening fixes from Kees Cook:
- randstruct: gcc-plugin: Fix attribute addition with GCC 15
- ubsan: integer-overflow: depend on BROKEN to keep this out of CI
- overflow: Introduce __DEFINE_FLEX for having no initializer
- wifi: iwlwifi: mld: Work around Clang loop unrolling bug
[ Take two after a jump scare due to some repo rewriting by 'b4' - Linus ]
* tag 'hardening-v6.16-rc1-fix1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
randstruct: gcc-plugin: Fix attribute addition
overflow: Introduce __DEFINE_FLEX for having no initializer
ubsan: integer-overflow: depend on BROKEN to keep this out of CI
wifi: iwlwifi: mld: Work around Clang loop unrolling bug
The nested loop in iwl_mld_send_proto_offload() confuses Clang into
thinking there could be a final loop iteration past the end of the
"nsc" array (which is only 4 entries). The FORTIFY checking in memcmp()
(via ipv6_addr_cmp()) notices this (due to the available bytes in the
out-of-bounds position of &nsc[4] being 0), and errors out, failing
the build. For some reason (likely due to architectural loop unrolling
configurations), this is only exposed on ARM builds currently. Due to
Clang's lack of inline tracking[1], the warning is not very helpful:
include/linux/fortify-string.h:719:4: error: call to '__read_overflow' declared with 'error' attribute: detected read beyond size of object (1st parameter)
719 | __read_overflow();
| ^
1 error generated.
But this was tracked down to iwl_mld_send_proto_offload()'s
ipv6_addr_cmp() call.
An upstream Clang bug has been filed[2] to track this. For now fix the
build by explicitly bounding the inner loop by "n_nsc", which is what
"c" is already limited to.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/2076
Link: https://github.com/llvm/llvm-project/pull/73552 [1]
Link: https://github.com/llvm/llvm-project/issues/136603 [2]
Link: https://lore.kernel.org/r/20250421204153.work.935-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
We have iwl_tx_cmd for devices older than 22000, iwl_tx_cmd_gen2 for
22000 devices, and iwl_tx_cmd_gen3 ax210 and up.
But the convention for all other APIs is to have the latest version
without any prefix and the older ones - with a _vX prefix,
where X is the highest version that this struct support.
The term 'gen' was introduced as the name of the (back then) new
transport, and should not be used as a device name (for that we have the
actual names: 22000, ax210, etc.)
Now as a new transport, called 'gen3', is going to be written and it can
be confused with this API.
Move iwl_tx_cmd to use the regular versioning convention.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.806e40c8f767.Ibc0e95e43a6fa6d47f72823bf804314d5db84618@changeid
