The firmware has handled quiet in CSA for a long time now, but
it didn't really matter much. However, now with quiet CSA on a
perhaps secondary link, we don't want mac80211 to stop queues,
we can continue using a link that's not requiring quiet. Set
the feature flag for MLO-capable devices indicating that we'll
handle the quiet entirely in the driver/device.
However, the firmware doesn't handle quiet in AP mode since we
don't really expect to really be needing that (without radar
detection), but - even for testing - make that work properly
by simply not pulling from TXQs in this scenario.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.fa75403b5eaa.Ie3ff02215f810fcfefd6a22c481567f94f61c0c6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If, for any reason, we're going to attempt to flush the queues
while quiet CSA is happening, this cannot succeed. This could
be the case if for example mac80211 were to flush after TXing
e.g. a deauth frame due to disconnecting during the CSA.
In this case, drop the frames instead, the firmware won't let
us do any transmissions and may also become unhappy if we're
not going to disconnect quickly enough.
Currently this doesn't happen as mac80211 stops queues, but
we'll want to let mac80211 know not to stop queues for proper
multi-link support during CSA, so we need to handle this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.d5d629f32ea8.I86d9b849d92273542bfc2d9c671b66179e7ebb72@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a conflict already and some upcoming changes
also depend on changes in wireless for being conflict-
free, so pull wireless in to make all that easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A DoS tool that injects loads of authentication frames made our AP
crash. The iwl_mvm_is_dup() function couldn't find the per-queue
dup_data which was not allocated.
The root cause for that is that we ran out of stations in the firmware
and we didn't really add the station to the firmware, yet we didn't
return an error to mac80211.
Mac80211 was thinking that we have the station and because of that,
sta_info::uploaded was set to 1. This allowed
ieee80211_find_sta_by_ifaddr() to return a valid station object, but
that ieee80211_sta didn't have any iwl_mvm_sta object initialized and
that caused the crash mentioned earlier when we got Rx on that station.
Cc: stable@vger.kernel.org
Fixes: 57974a55d9 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.1f76c44b2486.I6a00955e2842f15f0a089db2f834adb9d10fbe35@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some changes coming to wireless-next that will
otherwise cause conflicts, pull wireless in first to be
able to resolve that when applying the individual changes
rather than having to do merge resolution later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When connecting to an AP, we currently initialize the rate
control only after associating. Since we now use firmware
to assign rates to auth/assoc frames rather than using the
data in the station and the firmware doesn't know, they're
transmitted using low mandatory rates. However, if the AP
advertised only higher supported rates we want to use them
to be nicer (it still must receive mandatory rates though),
so send the information to the firmware earlier to have it
know about it and be able to use it.
Fixes: 499d027904 ("wifi: iwlwifi: Use FW rate for non-data frames")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.ed7ab1c859c2.I4b4d4fc3905c8d8470fc0fee4648f25c950c9bb7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wiphy_work infra ensures that the entire worker will run
with the wiphy mutex. It is useful to have RX handlers
running as a wiphy_work, when we don't want the handler to
run in parallel with mac80211 work (to avoid races).
For example - BT notification can disable eSR starting from the next
patch.
In ieee80211_set_active_links we first check that eSR is
allowed, (drv_can_activate_links) and then activate it.
If the BT notif was received after drv_can_activate_links
(which returned true), and before the activation - eSR will be
activated when it shouldn't.
If BT notif is handled with the wiphy mutex, it can't run in
parallel to ieee80211_set_active_links, which also holds that
mutex.
Add the necessary infrastructure here, for use in the next commit.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240123200528.ce83d16cdec8.I35ef53fa23f58b9ec17924099238b61deafcecd7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to get regulatory domain, driver sends MCC_UPDATE_CMD to the
FW. One of the parameters in the response is the status which can tell
if the regdomain has changed or not.
When iwl_mvm_init_mcc() is called during iwl_op_mode_mvm_start(), then
sband is still NULL and channel parameters (i.e. chan->flags) cannot be
initialized. When, further in the flow, iwl_mvm_update_mcc() is called
during iwl_mvm_up(), it first checks if the regdomain has changed and
then skips the update if it remains the same. But, since channel
parameters weren't initialized yet, the update should be forced in this
codepath. Fix that by adding a corresponding parameter to
iwl_mvm_init_fw_regd().
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.78b2c5b891b0.Iac49d52e0bfc0317372015607c63ea9276bbb188@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Multi rx queue allows to spread the load of the Rx streams on different
CPUs. 9000 series required complex synchronization mechanisms from the
driver side since the hardware / firmware is not able to provide
information about duplicate packets and timeouts inside the reordering
buffer.
Users have complained that for newer devices, all those synchronization
mechanisms have caused spurious packet drops. Those packet drops
disappeared if we simplify the code, but unfortunately, we can't have
RSS enabled on 9000 series without this complex code.
Remove support for RSS on 9000 so that we can make the code much simpler
for newer devices and fix the bugs for them.
The down side of this patch is a that all the Rx path will be routed to
a single CPU, but this has never been an issue, the modern CPUs are just
fast enough to cope with all the traffic.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.2917eb8b7af9.Iddd7dcf335387ba46fcbbb6067ef4ff9cd3755a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As session protection API is moving to be per link instead of per mac,
move the time events to be per link too.
Since there is only one concurrent time event per mac, it feels
unnecessary to have the time_event as a member of iwl_mvm_link_info.
(That way we will have to iterate over all links each time we want to
clear a time event, and also we will need mac80211 to tell us the link
id when mgd_tx_complete() is called.)
So leave this as a member of iwl_mvm_vif, but add the link id to the
time_event structure.
The link id in time_event will only be maintained and used for:
1. When SESSION_PROTECTION_CMD is supported (before it, we don't have MLO)
2. For time_events of types SESSION_PROTECT_CONF_ASSOC,
SESSION_PROTECT_CONF_P2P_DEVICE_DISCOV, and
SESSION_PROTECT_CONF_P2P_GO_NEGOTIATION
(not for aux roc/ Hot Spot time_events).
For P2P, non-MLO connections, and pre-MLD API, deflink id, meaning 0,
will be used
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.21496bcacb18.I79d037325b4fae4c12a22d9477e53fc9c537ad46@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When I implemented iwl_mvm_mac_flush_sta() I completely botched it;
it basically always happens after the iwl_mvm_sta_pre_rcu_remove()
call, and that already clears mvm->fw_id_to_mac_id[] entries, so we
cannot rely on those at iwl_mvm_mac_flush_sta() time. This means it
never did anything.
Fix this by just going through the station IDs and now with the new
API for iwl_mvm_flush_sta(), call those.
Fixes: a6cc6ccb1c ("wifi: iwlwifi: mvm: support new flush_sta method")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.0b5878e93118.I1093e60163052e7be64d2b01424097cd6a272979@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
From its very first stages of development, iwlmvm added all the PHY
context immediately upon firmware boot. Then, all we needed to do is to
modify the contexts. This was fine if the addition of a PHY context that
we don't need is free. This was true until now. Newer devices will run
calibrations upon the addition of a PHY context.
Change the way we work with PHY context in iwlmvm. Fortunately, we
already have all the ref counting in place so that it is not very hard
to do.
Also, since we now remove the PHY context before the link is removed
(but after it has been de-activated of course), it'll confuse the
firmware if we put the late phy_id into the LINK command that removes
the link. Change this to put an invalid phy_id just like we do when we
add a link that has no PHY context yet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.55a1a78719be.I2032a7d227b57f4fc4370a2793476d47538404fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bss_info_changed() callback of mac80211 was originally in both
MLD and non-MLD API. Therefore, we extracted the common part
to a function which receives a callback structure with the
mode-specific (non-MLO\MLO) ops. Eventually, for MLO API,
bss_info_changed() callback was split into 2 callbacks:
link_info_changed() and vif_cfg_changed() so it is no longer in use
for MLO, only for non-MLO.
Remove the code that uses the mode-specific callback structure.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.b65fbcdb9295.I2a64a6f1178ee0466755d728addc77acbb2ed6f4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add simple logic that would allow using EMLSR in case
there are multiple valid links:
- In case the connection establishment has just been
completed try to find a valid link pair for EMLSR
functionality where one of the links in the pair is
the current active link.
- In case the valid links changed after connection
was already established, try to find a valid link pair
for EMLSR functionality, in case the EMSLR is not active
yet.
If a valid link pair is found call mac80211 to asynchronously
set the new link pair, otherwise continue using the current active
links.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004123422.0c7b89ab29c2.I6600bd16551d75e2bf520d8d0add525568a9f85f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
