- Check only PCIE_LINKUP, not LTSSM status, to determine whether the link
is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s for Root
Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead of
rockchip_pcie_ep_pre_init() so it stays hidden after PERST# resets
non-sticky registers (Shawn Lin)
- Remove unused PCIE_CLIENT_GENERAL_DEBUG definition (Hans Zhang)
- Organize register and bitfield definitions logically (Hans Zhang)
- Use rockchip_pcie_link_up() to check link up instead of open coding, and
use GENMASK() and FIELD_GET() when possible (Hans Zhang)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up() and
armada8k, dra7xx, dw-rockchip, exynos, histb, keembay, keystone, kirin,
meson, qcom, qcom-ep, rcar_gen4, spear13xx, tegra194, uniphier, visconti
(Hans Zhang)
- Return bool (not int) for link-up check in mobiveil_pab_ops.link_up() and
layerscape-gen4, mobiveil (Hans Zhang)
- Simplify j721e link-up check (Hans Zhang)
- Convert pci-host-common to a library so platforms that don't need native
host controller drivers don't need to include these helper functions
(Manivannan Sadhasivam)
* pci/controller/dw-rockchip:
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI: cadence: Simplify J721e link status check
PCI: mobiveil: Return bool from link up check
PCI: dwc: Return bool from link up check
PCI: dw-rockchip: Fix PHY function call sequence in rockchip_pcie_phy_deinit()
PCI: dw-rockchip: Use rockchip_pcie_link_up() to check link up instead of open coding
PCI: dw-rockchip: Reorganize register and bitfield definitions
PCI: dw-rockchip: Remove unused PCIE_CLIENT_GENERAL_DEBUG definition
PCI: dw-rockchip: Move rockchip_pcie_ep_hide_broken_ats_cap_rk3588() to dw_pcie_ep_ops::init()
PCI: dw-rockchip: Enable ASPM L0s capability for both RC and EP modes
PCI: dw-rockchip: Remove PCIE_L0S_ENTRY check from rockchip_pcie_link_up()
# Conflicts:
# drivers/pci/controller/pcie-apple.c
# include/linux/pci-ecam.h
The j721e driver has a single platform driver that can be built-in or a
loadable module, but it calls two separate backend drivers depending on
whether it is a host or endpoint.
If the two modes are not the same, we can end up with a situation where the
built-in pci-j721e driver tries to call the modular host or endpoint
driver, which causes a link failure:
ld.lld-21: error: undefined symbol: cdns_pcie_ep_setup
>>> referenced by pci-j721e.c
>>> drivers/pci/controller/cadence/pci-j721e.o:(j721e_pcie_probe) in archive vmlinux.a
ld.lld-21: error: undefined symbol: cdns_pcie_host_setup
>>> referenced by pci-j721e.c
>>> drivers/pci/controller/cadence/pci-j721e.o:(j721e_pcie_probe) in archive vmlinux.a
Rework the dependencies so that the 'select' is done by the common Kconfig
symbol, based on which of the two are enabled. Effectively this means that
having one built-in makes the other either built-in or disabled, but all
configurations will now build.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20250423162523.2060405-1-arnd@kernel.org
Commit e49ad66781 ("PCI: j721e: Add TI J784S4 PCIe configuration")
assigned the value of .linkdown_irq_regfield for the J784S4 SoC as the
"LINK_DOWN" macro corresponding to BIT(1), and as a result, the Link
Down interrupts on J784S4 SoC are missed.
According to the Technical Reference Manual and Register Documentation
for the J784S4 SoC[1], BIT(1) corresponds to "ENABLE_SYS_EN_PCIE_DPA_1",
which is not the correct field for the link-state interrupt. Instead, it
is BIT(10) of the "PCIE_INTD_ENABLE_REG_SYS_2" register that corresponds
to the link-state field named as "ENABLE_SYS_EN_PCIE_LINK_STATE".
Thus, set .linkdown_irq_regfield to the macro "J7200_LINK_DOWN", which
expands to BIT(10) and was first defined for the J7200 SoC. Other SoCs
already reuse this macro since it accurately represents the "link-state"
field in their respective "PCIE_INTD_ENABLE_REG_SYS_2" register.
1: https://www.ti.com/lit/zip/spruj52
Fixes: e49ad66781 ("PCI: j721e: Add TI J784S4 PCIe configuration")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, add a missing .linkdown_irq_regfield member
set to the J7200_LINK_DOWN macro to struct j7200_pcie_ep_data]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250305132018.2260771-1-s-vadapalli@ti.com
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100 us),
before deasserting PERST# to ensure power and refclk are stable
(Siddharth Vadapalli)
* pci/controller/j721e:
PCI: j721e: Deassert PERST# after a delay of PCIE_T_PVPERL_MS milliseconds
PCI: j721e: Add PCIe support for J722S SoC
According to Section 2.2 of the PCI Express Card Electromechanical
Specification (Revision 5.1), in order to ensure that the power and the
reference clock are stable, PERST# has to be deasserted after a delay of
100 milliseconds (TPVPERL).
Currently, it is being assumed that the power is already stable, which
is not necessarily true.
Hence, change the delay to PCIE_T_PVPERL_MS to guarantee that power and
reference clock are stable.
Fixes: f3e25911a4 ("PCI: j721e: Add TI J721E PCIe driver")
Fixes: f96b697137 ("PCI: j721e: Use T_PERST_CLK_US macro")
Link: https://lore.kernel.org/r/20241104074420.1862932-1-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The ACSPCIE module is capable of driving the reference clock required by
the PCIe Endpoint device. It is an alternative to on-board and external
reference clock generators. Enabling the output from the ACSPCIE module's
PAD IO Buffers requires clearing the "PAD IO disable" bits of the
ACSPCIE_PROXY_CTRL register in the CTRL_MMR register space.
Add support to enable the ACSPCIE reference clock output using the optional
device-tree property "ti,syscon-acspcie-proxy-ctrl".
Link: https://lore.kernel.org/linux-pci/20240829105316.1483684-3-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus. As
part of that merge prepping Arm DT support 13 years ago, they "temporarily"
include each other. They also include platform_device.h and of.h. As a
result, there's a pretty much random mix of those include files used
throughout the tree. In order to detangle these headers and replace the
implicit includes with struct declarations, users need to explicitly
include the correct includes.
Link: https://lore.kernel.org/r/20230714174827.4061572-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20230321193208.366561-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Clear FLR (Function Level Reset) from device capabilities
registers for all physical functions.
During FLR, the Margining Lane Status and Margining Lane Control
registers should not be reset, as per PCIe specification.
However, the controller incorrectly resets these registers upon FLR.
This causes PCISIG compliance FLR test to fail. Hence preventing
all functions from advertising FLR support if flag quirk_disable_flr
is set.
Link: https://lore.kernel.org/r/1635165075-89864-1-git-send-email-pthombar@cadence.com
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Christian reported a NULL pointer dereference in j721e_pcie_probe() caused
by 19e863828a ("PCI: j721e: Drop redundant struct device *"), which
removed struct j721e_pcie.dev since there's another copy in struct
cdns_pcie.dev reachable via j721e_pcie->cdns_pcie->dev.
The problem is that j721e_pcie->cdns_pcie was dereferenced before being
initialized:
j721e_pcie_probe
pcie = devm_kzalloc() # struct j721e_pcie
j721e_pcie_ctrl_init(pcie)
dev = pcie->cdns_pcie->dev <-- dereference cdns_pcie
switch (mode) {
case PCI_MODE_RC:
cdns_pcie = ... # alloc as part of pci_host_bridge
pcie->cdns_pcie = cdns_pcie <-- initialize pcie->cdns_pcie
Move the cdns_pcie initialization earlier so it is done before it is used.
This also simplifies the error exits.
Fixes: 19e863828a ("PCI: j721e: Drop redundant struct device *")
Link: https://lore.kernel.org/r/20220127222951.GA144828@bhelgaas
Link: https://lore.kernel.org/r/20220124122132.435743-1-christian.gmeiner@gmail.com
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
- Add DT binding and TI j721e support for refclk to PCIe connector (Kishon
Vijay Abraham I)
- Add host mode and endpoint mode DT bindings for TI AM64 SoC (Kishon Vijay
Abraham I)
* remotes/lorenzo/pci/cadence:
PCI: j721e: Add support to provide refclk to PCIe connector
dt-bindings: PCI: ti,j721e: Add endpoint mode dt-bindings for TI's AM64 SoC
dt-bindings: PCI: ti,j721e: Add host mode dt-bindings for TI's AM64 SoC
dt-bindings: PCI: ti,j721e: Add binding to represent refclk to the connector
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for altera,
brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene,
xilinx, xilinx-nwl (Rob Herring)
- Convert to devm_platform_ioremap_resource_byname() instead of open-coding
platform_get_resource_byname() and devm_ioremap_resource() for altera,
cadence, mediatek, rockchip, tegra, xgene (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() instead of open-coding
platform_get_resource() and devm_ioremap_resource() for aardvark,
brcmstb, exynos, ftpci100, versatile (Dejin Zheng)
- Remove redundant error messages from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Drop useless PCI_ENABLE_PROC_DOMAINS from versatile driver (Rob Herring)
- Default host bridge parent device to the platform device (Rob Herring)
- Drop unnecessary zeroing of host bridge fields (Rob Herring)
- Use pci_is_root_bus() instead of tracking root bus number separately in
aardvark, designware (imx6, keystone, designware-host), mobiveil,
xilinx-nwl, xilinx, rockchip, rcar (Rob Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of each
driver for aardvark, designware-host, host-common, mediatek, rcar, tegra,
v3-semi (Rob Herring)
- Use bridge resources instead of parsing DT 'ranges' again for cadence
(Rob Herring)
- Remove private bus number and range from cadence (Rob Herring)
- Use devm_pci_alloc_host_bridge() to simplify rcar (Rob Herring)
- Use struct pci_host_bridge.windows list directly rather than a temporary
(Rob Herring)
- Reduce OF "missing non-prefetchable window" from error to warning message
(Rob Herring)
- Convert rcar-gen2 from old Arm-specific pci_common_init_dev() to new
arch-independent interfaces (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers that
don't support legacy IRQs (iproc) need to undo this (Rob Herring)
* pci/host-probe-refactor:
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: of: Reduce missing non-prefetchable memory region to a warning
PCI: rcar: Use struct pci_host_bridge.windows list directly
PCI: rcar: Use devm_pci_alloc_host_bridge()
PCI: cadence: Remove private bus number and range storage
PCI: cadence: Use bridge resources for outbound window setup
PCI: Move setting pci_host_bridge.busnr out of host drivers
PCI: rcar: Use pci_is_root_bus() to check if bus is root bus
PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx-nwl: Use pci_is_root_bus() to check if bus is root bus
PCI: mobiveil: Use pci_is_root_bus() to check if bus is root bus
PCI: designware: Use pci_is_root_bus() to check if bus is root bus
PCI: aardvark: Use pci_is_root_bus() to check if bus is root bus
PCI: Drop unnecessary zeroing of bridge fields
PCI: Set default bridge parent device
PCI: versatile: Drop flag PCI_ENABLE_PROC_DOMAINS
PCI: controller: Remove duplicate error message
PCI: controller: Convert to devm_platform_ioremap_resource()
PCI: controller: Convert to devm_platform_ioremap_resource_byname()
PCI: xilinx: Use pci_host_probe() to register host
PCI: xilinx-nwl: Use pci_host_probe() to register host
PCI: rockchip: Use pci_host_probe() to register host
PCI: rcar: Use pci_host_probe() to register host
PCI: iproc: Use pci_host_probe() to register host
PCI: altera: Use pci_host_probe() to register host
PCI: xgene: Use pci_host_probe() to register host
PCI: versatile: Use pci_host_probe() to register host
PCI: v3: Use pci_host_probe() to register host
PCI: tegra: Use pci_host_probe() to register host
PCI: mobiveil: Use pci_host_probe() to register host
PCI: brcmstb: Use pci_host_probe() to register host
PCI: host-common: Use struct pci_host_bridge.windows list directly
PCI: mvebu: Use struct pci_host_bridge.windows list directly
PCI: cadence: Use struct pci_host_bridge.windows list directly
# Conflicts:
# drivers/pci/controller/cadence/pcie-cadence-host.c
Add support for PCIe controller in J721E SoC. The controller uses the
Cadence PCIe core programmed by pcie-cadence*.c. The PCIe controller
will work in both host mode and device mode.
Some of the features of the controller are:
*) Supports both RC mode and EP mode
*) Supports MSI and MSI-X support
*) Supports upto GEN3 speed mode
*) Supports SR-IOV capability
*) Ability to route all transactions via SMMU (support will be added
in a later patch).
Link: https://lore.kernel.org/r/20200722110317.4744-14-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
