Call common DWC suspend/resume function. Use DWC common iATU method to
send out PME_TURN_OFF message.
In old DWC implementations, PCIE_ATU_INHIBIT_PAYLOAD in iATU Ctrl2 register
is reserved, so the generic DWC implementation of sending the PME_Turn_Off
message using a dummy MMIO write cannot be used. Use the previous method to
kick off PME_TURN_OFF message for these platforms.
The System Reset Control (SRC) interface is used to toggle 'turnoff_reset'
to send PME_TURN_OFF and since the DWC implementation is used, it is not
needed now.
Replace the imx_pcie_stop_link() and imx_pcie_host_exit() by
dw_pcie_suspend_noirq() in imx_pcie_suspend_noirq().
Since dw_pcie_suspend_noirq() already does these, see below call stack:
dw_pcie_suspend_noirq()
dw_pcie_stop_link()
imx_pcie_stop_link()
pci->pp.ops->deinit()
imx_pcie_host_exit()
Replace the imx_pcie_host_init(), dw_pcie_setup_rc() and
imx_pcie_start_link() by dw_pcie_resume_noirq() in imx_pcie_resume_noirq().
Since dw_pcie_resume_noirq() already does these, see below call stack:
dw_pcie_resume_noirq()
pci->pp.ops->init()
imx_pcie_host_init()
dw_pcie_setup_rc()
dw_pcie_start_link()
imx_pcie_start_link(;
Link: https://lore.kernel.org/r/20241126075702.4099164-9-hongxing.zhu@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pcie-designware.h declared dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq() unconditionally, even though they were only
implemented when CONFIG_PCIE_DW_HOST was defined.
Add no-op stubs for them when CONFIG_PCIE_DW_HOST is not defined so
drivers that support both Root Complex and Endpoint modes don't need
Link: https://lore.kernel.org/r/20250117213810.GA656803@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On the i.MX8QM, PCIe link can't be re-established again in
dw_pcie_resume_noirq(), if the LTSSM_EN bit is not cleared
properly in dw_pcie_suspend_noirq().
So, add dw_pcie_stop_link() to dw_pcie_suspend_noirq() to fix
this issue and to align the suspend/resume functions since there
is dw_pcie_start_link() in dw_pcie_resume_noirq() already.
Fixes: 4774faf854 ("PCI: dwc: Implement generic suspend/resume functionality")
Link: https://lore.kernel.org/r/20241210081557.163555-2-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Root Complex specific device tree binding for pcie-dw-rockchip has the
'sys' interrupt marked as required.
The driver requests the 'sys' IRQ unconditionally, and errors out if not
provided.
Thus, we can unconditionally set 'use_linkup_irq', so dw_pcie_host_init()
doesn't wait for the link to come up.
This will skip the wait for link up (since the bus will be enumerated once
the link up IRQ is triggered), which reduces the bootup time.
Link: https://lore.kernel.org/r/20250113-rockchip-no-wait-v1-1-25417f37b92f@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Most boards using the pcie-dw-rockchip PCIe controller lack standard
hotplug support.
Thus, when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. This can be avoided by using the
'dll_link_up' interrupt in the combined system interrupt 'sys'.
Once the 'dll_link_up' IRQ is received, the bus underneath the host bridge
is scanned to enumerate PCIe endpoint devices.
This implements the same functionality that was implemented in the DWC
based pcie-qcom driver in 4581403f67 ("PCI: qcom: Enumerate endpoints
based on Link up event in 'global_irq' interrupt").
The Root Complex specific device tree binding for pcie-dw-rockchip already
has the 'sys' interrupt marked as required, so there is no need to update
the device tree binding. This also means that we can request the 'sys' IRQ
unconditionally.
Link: https://lore.kernel.org/r/20241127145041.3531400-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, squash Pei Xiao's redundant dev_err() fix from
https://lore.kernel.org/r/327718207d3cd72847c079ff9d56eb246744c182.1736126067.git.xiaopei01@kylinos.cn,
squash Niklas's #define change from https://lore.kernel.org/r/20250103095812.2408364-2-cassel@kernel.org]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in
'global_irq' interrupt") added the Link Up-based enumeration support, but
did not update the ICC/OPP vote once link is up. Before that, the update
happened during probe and the endpoints may or may not be enumerated at
that time, so the ICC/OPP vote was not guaranteed to be accurate.
With Link Up-based enumeration support, the driver can request the accurate
vote based on the PCIe link.
Call qcom_pcie_icc_opp_update() in qcom_pcie_global_irq_thread() after
enumerating the endpoints.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-3-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Increase the size of the string buffer to avoid potential truncation in
dw_pcie_edma_irq_verify().
This fixes the following build warning when compiling with W=1:
drivers/pci/controller/dwc/pcie-designware.c: In function ‘dw_pcie_edma_detect’:
drivers/pci/controller/dwc/pcie-designware.c:989:50: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 3 [-Wformat-truncation=]
989 | snprintf(name, sizeof(name), "dma%d", pci->edma.nr_irqs);
| ^~
Link: https://lore.kernel.org/r/20250104002119.2681246-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-1-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add "ref" clock to enable Refclk. To avoid breaking DT backwards
compatibility, the i.MX95 "ref" clock is optional. Use
devm_clk_get_optional() to fetch i.MX95 PCIe optional clocks in driver.
If using external clock, "ref" clock should point to external reference.
If using internal clock, CREF_EN in LAST_TO_REG controls reference output,
implemented in drivers/clk/imx/clk-imx95-blk-ctl.c.
Link: https://lore.kernel.org/r/20241126075702.4099164-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
For the i.MX95, the configuration of a LUT is necessary to convert PCIe
Requester IDs (RIDs) to StreamIDs, which are used by both IOMMU and ITS.
This involves checking msi-map and iommu-map device tree properties to
ensure consistent mapping of Requester IDs to the same StreamIDs.
Subsequently, LUT-related registers are configured. If a msi-map isn't
detected, the platform relies on DWC built-in controller for MSIs that
do not need StreamIDs.
Implement PCI bus callback function to handle enable_device() and
disable_device() operations, setting up the LUT whenever a new PCI
device is enabled.
Known limitations:
- If iommu-map exists in the device tree but the IOMMU controller is
disabled, StreamIDs are programmed into the LUT. However, if a RID
is out of range of the iommu-map, enabling the PCI device would
result in a failure, although the PCI device can work without the
IOMMU.
- If msi-map exists in the device tree but the MSI controller is
disabled, MSIs will not work. The DWC driver skips initializing the
built-in MSI controller, falling back to legacy PCI INTx only.
Link: https://lore.kernel.org/r/20250114-imx95_lut-v9-2-39f58dbed03a@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: fix uninitialized "sid" in imx_pcie_enable_device()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Instead of marking individual interrupts as safe to be migrated in
arbitrary contexts, mark the interrupt chips, which require the interrupt
to be moved in actual interrupt context, with the new IRQCHIP_MOVE_DEFERRED
flag. This makes more sense because this is a per interrupt chip property
and not restricted to individual interrupts.
That flips the logic from the historical opt-out to a opt-in model. This is
simpler to handle for other architectures, which default to unrestricted
affinity setting. It also allows to cleanup the redundant core logic
significantly.
All interrupt chips, which belong to a top-level domain sitting directly on
top of the x86 vector domain are marked accordingly, unless the related
setup code marks the interrupts with IRQ_MOVE_PCNTXT, i.e. XEN.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/all/20241210103335.563277044@linutronix.de
Currently, the driver acquires and asserts/deasserts the resets
individually thereby making the driver complex to read.
This can be simplified by using the reset_control_bulk() APIs.
Use devm_reset_control_bulk_get_exclusive() API to acquire all the resets
and use reset_control_bulk_{assert/deassert}() APIs to assert/deassert them
in bulk.
Following the recommendations in 'Rockchip RK3399 TRM v1.3 Part2':
1. Split the reset controls into two groups as per section '17.5.8.1.1
PCIe as Root Complex'.
2. Deassert the 'Pipe, MGMT Sticky, MGMT, Core' resets in groups as per
section '17.5.8.1.1 PCIe as Root Complex'. This is accomplished using
the reset_control_bulk APIs.
Link: https://lore.kernel.org/r/20241202151150.7393-3-linux.amoon@gmail.com
Co-developed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: squash error handling fix from https://lore.kernel.org/r/7da6ac56-af55-4436-9597-6af24df8122c@stanley.mountain]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When compiling the Rockchip endpoint driver with -W=1, the following
warnings can be seen in the output:
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_irq' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_asserted' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_up' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_training' not described in 'rockchip_pcie_ep'
Fix these warnings by adding the missing field descriptions in
struct rockchip_pcie_ep kernel-doc comment.
Fixes: a7137cbf6b ("PCI: rockchip-ep: Handle PERST# signal in EP mode")
Fixes: bd6e61df4b ("PCI: rockchip-ep: Improve link training")
Link: https://lore.kernel.org/r/20241216133404.540736-1-dlemoal@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The rcar_pcie_parse_outbound_ranges() uses the devm_request_mem_region()
macro to request a needed resource. A string variable that lives on the
stack is then used to store a dynamically computed resource name, which
is then passed on as one of the macro arguments. This can lead to
undefined behavior.
Depending on the current contents of the memory, the manifestations of
errors may vary. One possible output may be as follows:
$ cat /proc/iomem
30000000-37ffffff :
38000000-3fffffff :
Sometimes, garbage may appear after the colon.
In very rare cases, if no NULL-terminator is found in memory, the system
might crash because the string iterator will overrun which can lead to
access of unmapped memory above the stack.
Thus, fix this by replacing outbound_name with the name of the previously
requested resource. With the changes applied, the output will be as
follows:
$ cat /proc/iomem
30000000-37ffffff : memory2
38000000-3fffffff : memory3
Fixes: 2a6d0d63d9 ("PCI: rcar: Add endpoint mode support")
Link: https://lore.kernel.org/r/tencent_DBDCC19D60F361119E76919ADAB25EC13C06@qq.com
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: King Dix <kingdix10@qq.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Airoha EN7581 has a hw bug asserting/releasing PERST# signal causing
occasional PCIe link down issues. In order to overcome the problem,
PERST# signal is not asserted/released during device probe or
suspend/resume phase and the PCIe block is reset using
en7523_reset_assert() and en7581_pci_enable().
Introduce flags field in the mtk_gen3_pcie_pdata struct in order to
specify per-SoC capabilities.
Link: https://lore.kernel.org/r/20250109-pcie-en7581-rst-fix-v4-1-4a45c89fb143@kernel.org
Tested-by: Hui Ma <hui.ma@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Airoha EN7581 has a hw bug asserting/releasing PCIE_PE_RSTB signal
causing occasional PCIe link down issues. In order to overcome the
problem, PCIe block is reset using REG_PCI_CONTROL (0x88) and
REG_RESET_CONTROL (0x834) registers available in the clock module
running clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up().
In order to make the code more readable, move the wait for the time
needed to complete the PCIe reset from en7581_pci_enable() to
mtk_pcie_en7581_power_up().
Reduce reset timeout from 250ms to the standard PCIE_T_PVPERL_MS value
(100ms) since it has no impact on the driver behavior.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-4-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
The helper devm_clk_bulk_get_all_enable() missed to return the number of
clocks stored in the clk_bulk_data table referenced by the clks
argument and, therefore, will be dropped.
Use the newly introduced devm_clk_bulk_get_all_enabled() variant
instead, which is consistent with devm_clk_bulk_get_all() in terms of
the returned value:
> 0 if one or more clocks have been stored
= 0 if there are no clocks
< 0 if an error occurred
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20241217-clk_bulk_ena_fix-v5-2-aafbbb245155@collabora.com
Acked-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the Xilinx Versal CPM5 Root Port Controller 1. The key
difference between Controller 0 and Controller 1 lies in the
platform-specific error interrupt bits, which are located at different
register offsets.
To handle these differences, updated variant structure to hold the
following platform-specific details:
- Interrupt status register offset (ir_status)
- Interrupt enable register offset (ir_enable)
- Miscellaneous interrupt values (ir_misc_value)
The driver differentiates between Controller 0 and Controller 1 using the
compatible string in the device tree. This ensures that the appropriate
register offsets are used for each controller, allowing for correct
handling of platform-specific interrupts and initialization.
Link: https://lore.kernel.org/r/20240922061318.2653503-3-thippesw@amd.com
Signed-off-by: Thippeswamy Havalige <thippesw@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
All non-DWC EPC drivers implement (struct pci_epc *)->ops->get_features().
All DWC EPC drivers implement (struct dw_pcie_ep *)->ops->get_features(),
except for pcie-artpec6.c.
epc_features has been required in pci-epf-test.c since commit 6613bc2301
("PCI: endpoint: Fix NULL pointer dereference for ->get_features()").
A follow-up commit will make further use of epc_features in EPC core code.
Implement epc_features in the only EPC driver where it is currently not
implemented.
Link: https://lore.kernel.org/r/20241213143301.4158431-12-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
dw_pcie_prog_ep_inbound_atu() is used to program an inbound iATU in
"BAR Match Mode".
A memory address returned by e.g. kmalloc() is guaranteed to have natural
alignment (aligned to the size of the allocation). It is however not
guaranteed that pci_epc_set_bar() (and thus dw_pcie_prog_ep_inbound_atu())
is supplied an address that has natural alignment. (An EPF driver can send
in an arbitrary physical address to pci_epc_set_bar().)
The DWC Databook description for the LWR_TARGET_RW and LWR_TARGET_HW fields
in the IATU_LWR_TARGET_ADDR_OFF_INBOUND_i registers state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
Add a check to ensure that the physical address programmed in the iATU is
aligned to the size of the BAR (BAR_MASK+1), as without this, we can get
hard to debug errors, as we could write to bits that are read-only (without
getting a write error), which could cause the iATU to end up redirecting to
a physical address that is different from the address that we intended.
Link: https://lore.kernel.org/r/20241213143301.4158431-11-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In commit 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Link: https://lore.kernel.org/r/20241213143301.4158431-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20241213143301.4158431-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
* pci/controller/vmd:
PCI: vmd: Add DID 8086:B06F and 8086:B60B for Intel client SKUs
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
* pci/controller/tegra194:
PCI: tegra194: Move controller cleanups to pex_ep_event_pex_rst_deassert()
- Fix address translation unit programming (Damien Le Moal)
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint .align
value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead of
searching for it, and verify that the address was mapped (Damien Le Moal)
- When mapping an endpoint window, verify that the address hasn't been
mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which fixes
intermittent page faults in memcpy_toio() and memcpy_fromio() (Damien Le
Moal)
- Rename rockchip_pcie_parse_ep_dt() to rockchip_pcie_ep_get_resources()
for consistency with similar DT interfaces (Damien Le Moal)
- Factor out memory allocations to tidy rockchip_pcie_ep_probe() (Damien Le
Moal)
- Factor out MSI-X quirk to tidy rockchip_pcie_ep_probe() (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and only in
the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and controller
configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it (Damien Le
Moal)
- Add a handler for PERST# signal so we can detect host resets and start
link training when exiting reset (Damien Le Moal)
* pci/controller/rockchip:
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
