Turns out some registers of pre-2.5 version of rxmacro codecs are not
located at the expected offsets but 0xc further away in memory. So far
the detected registers are CDC_RX_RX2_RX_PATH_SEC7 and
CDC_RX_RX2_RX_PATH_DSM_CTL.
CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n) macro incorrectly generates the address
0x540 for RX2 but it should be 0x54C and it also overwrites
CDC_RX_RX2_RX_PATH_SEC7 which is located at 0x540.
The same goes for CDC_RX_RXn_RX_PATH_SEC7(rx, n).
Fix this by introducing additional rxn_reg_stride2 offset. For 2.5 version
and above this offset will be equal to 0.
With such change the corresponding RXn() macros will generate the same
values for 2.5 codec version for all RX paths and the same old values
for pre-2.5 version for RX0 and RX1. However for the latter case with
RX2 path it will also add rxn_reg_stride2 on top.
While at this, also remove specific if-check for INTERP_AUX from
rx_macro_digital_mute() and rx_macro_enable_interp_clk(). These if-check
was used to handle such special offset for AUX interpolator but since
CDC_RX_RXn_RX_PATH_SEC7(rx, n) and CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n)
macros will generate the correst addresses of dsm register, they are no
longer needed.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20241016221049.1145101-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all drivers below sound/soc to use .remove(), with the eventual
goal to drop struct platform_driver::remove_new(). As .remove() and
.remove_new() have the same prototypes, conversion is done by just
changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20240909151230.909818-2-u.kleine-koenig@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has static 'struct regmap_config', which is then customized
depending on device version. This works fine, because there should not
be two devices in a system simultaneously and even less likely that such
two devices would have different versions, thus different regmap config.
However code is cleaner and more obvious when static data in the driver
is also const - it serves as a template.
Mark the 'struct regmap_config' as const and duplicate it in the probe()
with kmemdup to allow customizing per detected device variant.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240701-b4-qcom-audio-lpass-codec-cleanups-v3-3-6d98d4dd1ef5@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Srinivas Kandagatla <srinivas.kandagatla@linaro.org>:
This patchset adds support to reading codec version and also adds
support for v2.5 codec version in rx macro.
LPASS 2.5 and up versions have changes in some of the rx blocks which
are required to get headset functional correctly.
Tested this on SM8450, X13s and x1e80100 crd.
This changes also fixes issue with sm8450, sm8550, sm8660 and x1e80100.
The order in which clocks are stopped matters as some of the clock
like NPL are derived from MCLK.
Without this patch, Dragonboard RB5 DSP would crash with below error:
qcom_q6v5_pas 17300000.remoteproc: fatal error received:
ABT_dal.c:278:ABTimeout: AHB Bus hang is detected,
Number of bus hang detected := 2 , addr0 = 0x3370000 , addr1 = 0x0!!!
Turn off fsgen first, followed by npl and then finally mclk, which is exactly
the opposite order of enable sequence.
Fixes: 1dc3459009 ("ASoC: codecs: lpass: register mclk after runtime pm")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/20230323110125.23790-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20230315150745.67084-50-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we ended up with incorrect mclk rate which should be
1920000 instead of 96000, So far we were getting lucky as the same clk
is set to 192000 by wsa and va macro. This issue is discovered when there
is no wsa macro active and only rx or tx path is tested.
Fix this by setting correct rate.
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: af3d54b997 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-7-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Updates for v5.18
Quite a quiet release for ASoC, lots of work on drivers and platforms
but nothing too groundbreaking but not much on the core itself:
- Start of moving SoF to support multiple IPC mechanisms.
- Use of NHLT ACPI table to reduce the amount of quirking required for
Intel systems.
- Some building blocks for use in forthcoming Intel AVS driver for
legacy Intel DSP firmwares.
- Support for AMD PDM, Atmel PDMC, Awinic AW8738, i.MX cards with
TLV320AIC31xx, Intel machines with CS35L41 and ESSX8336, Mediatek
MT8181 wideband bluetooth, nVidia Tegra234, Qualcomm SC7280, Renesas
RZ/V2L, Texas Instruments TAS585M
For SoundWire Frame sync to be generated correctly we need both MCLK
and MCLKx2 (npl). Without pm runtime enabled these two clocks will remain on,
however after adding pm runtime support its possible that NPl clock could be
turned off even when SoundWire controller is active.
Fix this by enabling mclk and npl clk when SoundWire clks are enabled.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220224111718.6264-10-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the potential failure of the devm_regmap_init_mmio(), it will
return error pointer and be assigned to the regmap.
Then the error pointer will be dereferenced.
For example rx->regmap will be used in rx_macro_mclk_enable().
Therefore, it should be better to check it.
Fixes: af3d54b997 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: 809bcbcece ("ASoC: codecs: lpass-wsa-macro: Add support to WSA Macro")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220121171031.2826198-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
