[ Upstream commit 487eca11a3 ]
The system will be hang up during S3 suspend because of SMU is pending
for GC not respose the register CP_HQD_ACTIVE access request.This issue
root cause of accessing the GC register under enter GFX CGGPG and can
be fixed by disable GFX CGPG before perform suspend.
v2: Use disable the GFX CGPG instead of RLC safe mode guard.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Tested-by: Mengbing Wang <Mengbing.Wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 72f5b5a308 upstream.
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dec9de2ada ]
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 063e768ebd ]
This can fix the baco reset failure seen on Navi10.
And this should be a low risk fix as the same sequence
is already used for system suspend/resume.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5349775c1 ]
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0275dfc82 ]
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab7e274b8 ]
The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.
Signed-off-by: Yintian Tao <yttao@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 416611d9b6 ]
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c134c3caba ]
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df36f6cf23 ]
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34ad023006 ]
[why]
Need to fix DML portability issues to enable SW unit testing around DML
[how]
Move calcs into dc include folder since multiple components reference it
Remove relative paths to external dependencies
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bdac179e2 ]
Reading from /sys/kernel/debug/kfd/hang_hws would cause a kernel
oops because we didn't implement a read callback. Set the permission
to write-only to prevent that.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: shaoyunl <shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7489a7e1 ]
issues:
MEC is ruined by the amdkfd_pre_reset after VF FLR done
fix:
amdkfd_pre_reset() would ruin MEC after hypervisor finished the VF FLR,
the correct sequence is do amdkfd_pre_reset before VF FLR but there is
a limitation to block this sequence:
if we do pre_reset() before VF FLR, it would go KIQ way to do register
access and stuck there, because KIQ probably won't work by that time
(e.g. you already made GFX hang)
so the best way right now is to simply remove it.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1512d064f5 ]
issues:
gpu_recover() is re-entered by the mailbox interrupt
handler mxgpu_nv.c
fix:
we need to bypass the gpu_recover() invoke in mailbox
interrupt as long as the timeout is not infinite (thus the TDR
will be triggered automatically after time out, no need to invoke
gpu_recover() through mailbox interrupt.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5479034576 ]
[Why]
A corner case currently exists where DPP DTO is lowered before
pipes are updated to a higher viewport. This causes underflow
as the DPPCLK is too low for the current viewport.
[How]
Only lower DPP DTO when it is safe to lower, or if
the newer clocks are higher than the current ones.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 615b9b585e ]
[Why]
Previously update_bw_bounding_box for RN was commented out
due to incorrect values causing BSOD on Hybrid Graphics.
However, commenting out this function also may cause issues
such as underflow in certain cases such as 2x4K displays.
[How]
Fix dram_speed_mts calculations.
Update from proper index of clock_limits[]
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a63141e317 ]
Commit b0f3cd3191 ("drm/amdgpu: remove unnecessary JPEG2.0 code from
VCN2.0") introduced a new clang warning in the vcn_v2_0_stop function:
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: warning: variable 'r'
is used uninitialized whenever 'while' loop exits because its condition
is false [-Wsometimes-uninitialized]
SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
while ((tmp_ & (mask)) != (expected_value)) { \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1083:6: note: uninitialized use
occurs here
if (r)
^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: note: remove the
condition if it is always true
SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
^
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
while ((tmp_ & (mask)) != (expected_value)) { \
^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1072:7: note: initialize the
variable 'r' to silence this warning
int r;
^
= 0
1 warning generated.
To prevent warnings like this from happening in the future, make the
SOC15_WAIT_ON_RREG macro initialize its ret variable before the while
loop that can time out. This macro's return value is always checked so
it should set ret in both the success and fail path.
Link: https://github.com/ClangBuiltLinux/linux/issues/776
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bae028e3e5 ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c: In function
'amdgpu_atombios_get_connector_info_from_object_table':
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:26: warning: variable
'grph_obj_num' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:13: warning: variable
'grph_obj_id' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:37: warning: variable
'con_obj_type' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:24: warning: variable
'con_obj_num' set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Fixes: d38ceaf99e ("drm/amdgpu: add core driver (v4)")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cad8ff7ec ]
[Why]
For unknown reason, immediate flip with host VM translation on NV12
surface will underflow on last row of PTE.
[How]
Hack chroma viewport height to make fetch one more row of PTE.
Note that this will cause hubp underflow on all video underlay
cases, but the underflow is not user visible since it is in
blank region.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f38abc15d1 ]
The sdma_queue_count increment should be done before
execute_queues_cpsch(), which calls pm_calc_rlib_size() where
sdma_queue_count is used to calculate whether over_subscription is
triggered.
With the previous code, when a SDMA queue is created,
compute_queue_count in pm_calc_rlib_size() is one more than the
actual compute queue number, because the queue_count has been
incremented while sdma_queue_count has not. This patch fixes that.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eb6d7aca5 ]
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df5e984c8b ]
guest vm gets 0xffffffff when reading RCC_DEV0_EPF0_STRAP0,
as a consequence, the rev_id and external_rev_id are wrong.
workaround it by hardcoding the rev_id to 0, which is the default value.
v2. add comment in the code
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5b356c58 ]
[why]
Up to 4 ODM memory pieces are required per ODM combine and cannot
overlap, i.e. each ODM "session" has to use its own memory pieces.
The ODM-memory mapping is currently broken for generic case.
The maximum number of memory pieces is ASIC-dependent, but it's always
big enough to satisfy maximum number of ODM combines. Memory pieces
are mapped as a bit-map, i.e. one memory piece corresponds to one bit.
The OPTC doing ODM needs to select memory pieces by setting the
corresponding bits, making sure there's no overlap with other OPTC
instances that might be doing ODM.
The current mapping works only for OPTC instance indexes smaller than
3. For instance indexes 3 and up it practically maps no ODM memory,
causing black, gray or white screen in display configs that include
ODM on OPTC instance 3 or up.
[how]
Statically map two unique ODM memory pieces for each OPTC instance
and piece them together when programming ODM combine mode.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
