The previous generations were only supporting a single HDMI controller, but
that's about to change, so put an index as well to differentiate between
the two controllers.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Not all pixelvalve FIFOs in vc5 have the same depth, so we need to add that
to our vc4_crtc_data structure to be able to compute the fill level
properly later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HVS found in the BCM2711 has 6 outputs and 3 FIFOs, with each output
being connected to a pixelvalve, and some muxing between the FIFOs and
outputs.
Any output cannot feed from any FIFO though, and they all have a bunch of
constraints.
In order to support this, let's store the possible FIFOs each output can be
assigned to in the vc4_crtc_data, and use that information at atomic_check
time to iterate over all the CRTCs enabled and assign them FIFOs.
The channel assigned is then set in the vc4_crtc_state so that the rest of
the driver can use it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In vc5, the HVS has 6 outputs and 3 FIFOs (or channels), with
pixelvalves each being assigned to a given output, but each output can
then be muxed to feed from multiple FIFOs.
Since vc4 had that entirely static, both were probably equivalent, but
since that changes, let's rename hvs_channel to hvs_output in the
vc4_crtc_data, since a pixelvalve is really connected to an output, and
not to a FIFO.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The COB allocation depends on the HVS channel used for a given
pixelvalve.
While the channel allocation was entirely static in vc4, vc5 changes
that and at bind time, a pixelvalve can be assigned to multiple
HVS channels.
Let's prepare that rework by allocating the COB when it's actually
needed.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Some of the HDMI pixelvalves in vc5 output two pixels per clock cycle.
Let's put the number of pixel output per clock cycle in the CRTC data and
update the various calculations to reflect that.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Instead of creating planes for each CRTC, we eventually want to create all
the planes for each CRTCs.
In order to make that more convenient, let's iterate on the CRTCs in the
plane creation function instead of its caller.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The planes so far were created as part of the CRTC binding code with
each planes created associated only to one CRTC. However, the hardware
in the vc4 doesn't really have such constraint and can be used with any
CRTC.
In order to rework this, let's first move the overlay and cursor planes
creation to a function of its own.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HVS found in the BCM2711 is slightly different from the previous
generations.
Most notably, the display list layout changes a bit, the LBM doesn't have
the same size and the formats ordering for some formats is swapped.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BCM2711 has a reworked display pipeline, and the load tracker needs
some adjustement to operate properly. Let's add a compatible for BCM2711
and disable the load tracker until properly supported.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
vc4_drv.h doesn't have any include guards which prevents it from being
included twice. Let's add them.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The VPU has configured clocks for 4k (or not) via config.txt,
and will limit the choice of video modes based on that.
Make fkms query it for these limits too to avoid selecting modes
that can not be handled by the current clock setup.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
"32a3dbe drm/vc4: Nuke preclose hook" removed vc4_cancel_page_flip,
but vc4_fkms_cancel_page_flip was still be added to with the
fkms driver, even though it was never called.
Nuke it too.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The binner BO is not required until the V3D is in use, so avoid
allocating it at probe and do it on the first non-dumb BO allocation.
Keep track of which clients are using the V3D and liberate the buffer
when there is none left, using a kref. Protect the logic with a
mutex to avoid race conditions.
The binner BO is created at the time of the first render ioctl and is
destroyed when there is no client and no exec job using it left.
The Out-Of-Memory (OOM) interrupt also gets some tweaking, to avoid
enabling it before having allocated a binner bo.
We also want to keep the BO alive during runtime suspend/resume to avoid
failing to allocate it at resume. This happens when the CMA pool is
full at that point and results in a hard crash.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190516145544.29051-5-paul.kocialkowski@bootlin.com
One might want to use the VC4 display stack without using Mesa.
Similar to the debugfs fixes for not having all of the possible
display bits enabled, make sure you can't oops in vc4 if v3d isn't
enabled.
v2: Fix matching against other v3d variants (review by Paul), don't
forget to set irq_enabled so that the vblank uapi works
v3: Use -ENODEV instead of -EINVAL on Paul's suggestion.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401183559.3823-2-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
The global list of all debugfs entries for the driver was painful: the
list couldn't see into the components' structs, so each component had
its own debugs show function to find the component, then find the
regset and dump it. The components also had to be careful to check
that they were actually registered in vc4 before dereferencing
themselves, in case they weren't probed on a particular platform.
They routinely failed at that.
Instead, we can have the components add their debugfs callbacks to a
little list in vc4 to be registered at drm_dev_register() time, which
gets vc4_debugfs.c out of the business of knowing the whole list of
components.
Thanks to this change, dsi0 (if it existed) would register its node.
v2: Rebase on hvs_underrun addition.
v3: whitespace fixup
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401183559.3823-1-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
In order to test whether the load tracker is working as expected, we
need the ability to compare the commit result with the underrun
indication. With the load tracker always enabled, commits that are
expected to trigger an underrun are always rejected, so userspace
cannot get the actual underrun indication from the hardware.
Add a debugfs entry to disable/enable the load tracker, so that a DRM
commit expected to trigger an underrun can go through with the load
tracker disabled. The underrun indication is then available to
userspace and can be checked against the commit result with the load
tracker enabled.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220155124.25022-4-paul.kocialkowski@bootlin.com
The HVS block is supposed to fill the pixelvalve FIFOs fast enough to
meet the requested framerate. The problem is, the HVS and memory bus
bandwidths are limited, and if we don't take these limitations into
account we might end up with HVS underflow errors.
This patch is trying to model the per-plane HVS and memory bus bandwidth
consumption and take a decision at atomic_check() time whether the
estimated load will fit in the HVS and membus budget.
Note that we take an extra margin on the memory bus consumption to let
the system run smoothly when other blocks are doing heavy use of the
memory bus. Same goes for the HVS limit, except the margin is smaller in
this case, since the HVS is not used by external components.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220155124.25022-3-paul.kocialkowski@bootlin.com
We are about to use vc4_plane_mode_set() in the async check path, but
async check can decide that async update is not possible and force the
driver to fallback to a sync update.
All the checks that have been done on the plane state during async check
stay valid, and checking it again is not necessary. Add a ->checked
field to vc4_plane_state, and use it to track the status of the state
(checked or not).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130090254.594-3-boris.brezillon@bootlin.com
We are about to use vc4_plane_mode_set() in the async check path, and
async updates require that LBM size stay the same since they reuse the
LBM from the previous state. So we definitely don't want to allocate a
new LBM region that we know for sure will be free right away.
Move the LBM allocation out of vc4_plane_mode_set() and call the new
function (vc4_plane_update_lbm()) from vc4_plane_atomic_check().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130090254.594-2-boris.brezillon@bootlin.com
The hardware has a single block for applying a CTM prior to gamma lut.
It can be fed with pixels from one of our CRTC at a time and uses a
matrix with S0.9 scalars. Use private atomic state to reject attempts
from userland to apply CTM for more than one CRTC at a time and reject
matrices with scalars that we can't approximate without integer bits.
Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/218067/
The V3D engine has various hardware counters which might be interesting
to userspace performance analysis tools.
Expose new ioctls to create/destroy a performance monitor object and
query the counter values of this perfmance monitor.
Note that a perfomance monitor is given an ID that is only valid on the
file descriptor it has been allocated from. A performance monitor can be
attached to a CL submission and the driver will enable HW counters for
this request and update the performance monitor values at the end of the
job.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112090926.12538-1-boris.brezillon@free-electrons.com
This ioctl will allow us to purge inactive userspace buffers when the
system is running out of contiguous memory.
For now, the purge logic is rather dumb in that it does not try to
release only the amount of BO needed to meet the last CMA alloc request
but instead purges all objects placed in the purgeable pool as soon as
we experience a CMA allocation failure.
Note that the in-kernel BO cache is always purged before the purgeable
cache because those objects are known to be unused while objects marked
as purgeable by a userspace application/library might have to be
restored when they are marked back as unpurgeable, which can be
expensive.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20171019125748.3152-1-boris.brezillon@free-electrons.com
This has proven immensely useful for debugging memory leaks and
overallocation (which is a rather serious concern on the platform,
given that we typically run at about 256MB of CMA out of up to 1GB
total memory, with framebuffers that are about 8MB ecah).
The state of the art without this is to dump debug logs from every GL
application, guess as to kernel allocations based on bo_stats, and try
to merge that all together into a global picture of memory allocation
state. With this, you can add a couple of calls to the debug build of
the 3D driver and get a pretty detailed view of GPU memory usage from
/debug/dri/0/bo_stats (or when we debug print to dmesg on allocation
failure).
The Mesa side currently labels at the gallium resource level (so you
see that a 1920x20 pixmap has been created, presumably for the window
system panel), but we could extend that to be even more useful with
glObjectLabel() names being sent all the way down to the kernel.
(partial) example of sorted debugfs output with Mesa labeling all
resources:
kernel BO cache: 16392kb BOs (3)
tiling shadow 1920x1080: 8160kb BOs (1)
resource 1920x1080@32/0: 8160kb BOs (1)
scanout resource 1920x1080@32/0: 8100kb BOs (1)
kernel: 8100kb BOs (1)
v2: Use strndup_user(), use lockdep assertion instead of just a
comment, fix an array[-1] reference, extend comment about name
freeing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725182718.31468-2-eric@anholt.net
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
If we restrict this helper to only kms drivers (which is the case) we
can look up the correct mode easily ourselves. But it's a bit tricky:
- All legacy drivers look at crtc->hwmode. But that is updated already
at the beginning of the modeset helper, which means when we disable
a pipe. Hence the final timestamps might be a bit off. But since
this is an existing bug I'm not going to change it, but just try to
be bug-for-bug compatible with the current code. This only applies
to radeon&amdgpu.
- i915 tries to get it perfect by updating crtc->hwmode when the pipe
is off (i.e. vblank->enabled = false).
- All other atomic drivers look at crtc->state->adjusted_mode. Those
that look at state->requested_mode simply don't adjust their mode,
so it's the same. That has two problems: Accessing crtc->state from
interrupt handling code is unsafe, and it's updated before we shut
down the pipe. For nonblocking modesets it's even worse.
For atomic drivers try to implement what i915 does. To do that we add
a new hwmode field to the vblank structure, and update it from
drm_calc_timestamping_constants(). For atomic drivers that's called
from the right spot by the helper library already, so all fine. But
for safety let's enforce that.
For legacy driver this function is only called at the end (oh the
fun), which is broken, so again let's not bother and just stay
bug-for-bug compatible.
The benefit is that we can use drm_calc_vbltimestamp_from_scanoutpos
directly to implement ->get_vblank_timestamp in every driver, deleting
a lot of code.
v2: Completely new approach, trying to mimick the i915 solution.
v3: Fixup kerneldoc.
v4: Drop the WARN_ON to check that the vblank is off, atomic helpers
currently unconditionally call this. Recomputing the same stuff should
be harmless.
v5: Fix typos and move misplaced hunks to the right patches (Neil).
v6: Undo hunk movement (kbuild).
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-4-daniel.vetter@ffwll.ch
