Whilst the documentation for BCM2835 states that the HDMI state machine
clock needs to be 108% of the pixel clock, other documentation says
that it only has to be greater than the pixel clock. The firmware
uses 101%, and that allows 1920x1200@60Hz to work within the
constraint of the HSM clock being < 163.68MHz.
Adopt 101%, and increase the maximum pixel clock for vc4 to 162MHz
so that it too supports 1920x1200@60.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
This could be a revert of "drm/vc4: hdmi: Add an audio support flag"
as it is no longer needed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The audio configuration has changed for Pi4, so support the
configuration functions via the variant tables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
HDMI audio configuration was using fixed index numbers to
load in DT register settings.
Switch to using reg-names for flexibility and to match Pi4.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
ALSA's iec958 plugin by default sets the block start preamble
to 8, whilst this driver was programming the hardware to expect
0xF.
Amend the hardware config to match ALSA.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
If the encoder is disabled and re-enabled (eg mode change) all infoframes
are reset, whilst the audio subsystem know nothing about this change.
The driver therefore needs to reinstate the audio infoframe for
itself.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
The HSM clock needs to be setup at around 110% of the pixel rate. This
was done previously by setting the clock rate to 148.5MHz * 108% at
probe time and only check in mode_valid whether the mode pixel clock was
under 148.5MHz or not.
However, with 4k we need to change that frequency to a higher frequency
than 148.5MHz.
Let's change that logic a bit by setting the clock rate of the HSM clock
to the pixel rate at encoder_enable time. This would work for the
BCM2711 that support 4k resolutions and has a clock that can provide it,
but we still have to take care of a 4k panel plugged on a BCM283x SoCs
that wouldn't be able to use those modes, so let's define the limit in
the variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The mode_valid hook on the encoder uses a pointer to a drm_encoder called
crtc, which is pretty confusing. Let's rename it to encoder to make it
clear what it is.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Similarly to the audio support, CEC support is not there yet for the
BCM2711, so let's skip entirely the CEC initialization through a variant
flag.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The CEC init code was put directly into the bind function, which was quite
inconsistent with how the audio support was done, and would prevent us from
further changes to skip that initialisation entirely.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BCM2711 audio support doesn't work yet, so let's add a boolean to
indicate whether or not it's supported, and only register a sound card if
that boolean is set.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HDMI driver was registering a single debugfs file so far with the name
hdmi_regs.
Obviously, this is not going to work anymore when will have multiple HDMI
controllers since we will end up trying to register two files with the same
name.
Let's use the ID to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Some operations will need us to have the raw ID of the HDMI controller
in the BCM2711, such as the encoder type to register, the name of the
debugfs files, etc.
Let's add it to our variant structure.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Similarly to the previous patches, the timings setup in the HDMI controller
of the BCM2711 is slightly different, mostly because it supports higher
resolutions and thus needed more spaces for the various timings, resulting
in the register layout changing.
Let's add a callback for that as well.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Similarly to the previous patches, the CSC setup is slightly different in
the BCM2711 than in the previous generations. Let's add a callback for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Let's continue the implementation of hooks for the parts that change in the
BCM2711 SoC with the PHY RNG setup.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HDMI PHY in the BCM2711 HDMI controller is significantly more
complicated to setup than in the older BCM283x SoCs.
Let's add hooks to enable and disable the PHY.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BCM2711 and BCM283x HDMI controllers use a slightly different reset
sequence, so let's add a callback to reset the controller.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HDMI controllers found in the BCM2711 have most of the registers
reorganized in multiple registers areas and at different offsets than
previously found.
The logic however remains pretty much the same, so it doesn't really make
sense to create a whole new driver and we should share the code as much as
possible.
Let's implement some indirection to wrap around a register and depending on
the variant will lookup the associated register on that particular variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HDMI controllers found in the BCM2711 has a pretty different clock and
registers areas than found in the older BCM283x SoCs.
Let's create a variant structure to store the various adjustments we'll
need later on, and a function to get the resources needed for one
particular version.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4_hdmi_connector was only used to switch between drm_connector to
drm_encoder. However, we can now use vc4_hdmi to do the switch, so that
structure is redundant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Our CEC code also retrieves the associated vc4_hdmi by setting the
vc4_dev pointer as its private data, and then dereferences its vc4_hdmi
pointer.
In order to eventually get rid of that pointer, we can simply pass the
vc4_hdmi pointer directly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Whenever the code needs to access the vc4_hdmi structure from a DRM
connector or encoder, it first accesses the drm_device associated to the
connector, then retrieve the drm_dev private data which gives it a
pointer to our vc4_dev, and will finally follow the vc4_hdmi pointer in
that structure.
That will also give us some trouble when having multiple controllers,
but now that we have our encoder and connector structures that are part
of vc4_hdmi, we can simply call container_of on the DRM connector or
encoder and retrieve the vc4_hdmi structure directly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The function vc4_hdmi_connector_detect access its vc4_hdmi struct by
dereferencing the pointer in the structure vc4_dev. This will cause some
issues when we will have multiple HDMI controllers, so let's just use the
local variable for now instead of dereferencing that pointer all the time,
and we'll fix the local variable later.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current driver only supports a single HDMI controller, and part of
the issue is that the main vc4_dev structure holds a pointer to its
(only) HDMI controller, and the HDMI registers accessors will use it to
retrieve the mapped addresses.
Let's modify those accessors to use directly the vc4_hdmi structure so
that we can eventually get rid of that single global pointer.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The driver isn't consistent with the name given to the vc4_hdmi
structure pointer in its functions. Make sure to use a consistent name.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
the vc4_hdmi driver has some custom structures to hold the data it needs to
associate with the drm_encoder and drm_connector structures.
However, it allocates them separately from the vc4_hdmi structure which
makes it more complicated than it needs to be.
Move those structures to be contained by vc4_hdmi and update the code
accordingly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We will need to share the vc4_hdmi and related structures with multiple
files, so let's create a header for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We're calling vc4_debugfs_add_file with our struct vc4_hdmi pointer set
in the private field, but we don't use that field and go through the
main struct vc4_dev to get it.
Let's use the private field directly, that will save us some trouble
later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The previous generations were only supporting a single HDMI controller, but
that's about to change, so put an index as well to differentiate between
the two controllers.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Overlays are unable to remove properties in the base DTB, but they
can overwrite them. Allow a present but empty 'dmas' property
to also disable the HDMI audio interface.
See: https://github.com/raspberrypi/linux/issues/2489
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
commit 6c6de1c9e2 ("ASoC: vc4: vc4_hdmi: don't select unnecessary
Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 6c6de1c9e2 ("ASoC: vc4: vc4_hdmi: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The global list of all debugfs entries for the driver was painful: the
list couldn't see into the components' structs, so each component had
its own debugs show function to find the component, then find the
regset and dump it. The components also had to be careful to check
that they were actually registered in vc4 before dereferencing
themselves, in case they weren't probed on a particular platform.
They routinely failed at that.
Instead, we can have the components add their debugfs callbacks to a
little list in vc4 to be registered at drm_dev_register() time, which
gets vc4_debugfs.c out of the business of knowing the whole list of
components.
Thanks to this change, dsi0 (if it existed) would register its node.
v2: Rebase on hvs_underrun addition.
v3: whitespace fixup
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190401183559.3823-1-eric@anholt.net
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
