Some combinations of Pi 4Bs and Ethernet switches don't reliably get a
DCHP-assigned IP address, leaving the unit with a self=assigned 169.254
address. In the failure case, the Pi is left able to receive packets
but not send them, suggesting that the MAC<->PHY link is getting into
a bad state.
It has been found empirically that skipping a reset step by the genet
driver prevents the failures. No downsides have been discovered yet,
and unlike the forced renegotiation it doesn't increase the time to
get an IP address, so the workaround is enabled by default; add
genet.skip_umac_reset=n
to the command line to disable it.
See: https://github.com/raspberrypi/linux/issues/3108
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[ Upstream commit fe867cac9e ]
mlx5e_ethtool_set_channels updates the indirection table before
switching to the new channels. If the switch fails, the indirection
table is new, but the channels are old, which is wrong. Fix it by using
the preactivate hook of mlx5e_safe_switch_channels to update the
indirection table at the stage when nothing can fail anymore.
As the code that updates the indirection table is now encapsulated into
a new function, use that function in the attach flow when the driver has
to reduce the number of channels, and prepare the code for the next
commit.
Fixes: 85082dba0a ("net/mlx5e: Correctly handle RSS indirection table when changing number of channels")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dca147b3dc ]
mlx5e_safe_switch_channels accepts a callback to be called before
activating new channels. It is intended to configure some hardware
parameters in cases where channels are recreated because some
configuration has changed.
Recently, this callback has started being used to update the driver's
internal MLX5E_STATE_XDP_OPEN flag, and the following patches also
intend to use this callback for software preparations. This patch
renames the hw_modify callback to preactivate, so that the name fits
better.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2c95271f9 ]
As a preparation for one of the following commits, create a function to
encapsulate the code that notifies the kernel about the new amount of
RX and TX queues. The code will be called multiple times in the next
commit.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 21f64e72e7 upstream.
Commit 907a076881, forgot that we need to clear old values of
XGMAC_VLAN_TAG register when we switch from VLAN perfect matching to
HASH matching.
Fix it.
Fixes: 907a076881 ("net: stmmac: xgmac: fix incorrect XGMAC_VLAN_TAG register writting")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 806fd188ce ]
After commit bfcb813203 ("net: dsa:
configure the MTU for switch ports") my Lamobo R1 platform which uses
an allwinner,sun7i-a20-gmac compatible Ethernet MAC started to fail
by rejecting a MTU of 1536. The reason for that is that the DMA
capabilities are not readable on this version of the IP, and there
is also no 'tx-fifo-depth' property being provided in Device Tree. The
property is documented as optional, and is not provided.
Chen-Yu indicated that the FIFO sizes are 4KB for TX and 16KB for RX, so
provide these values through platform data as an immediate fix until
various Device Tree sources get updated accordingly.
Fixes: eaf4fac478 ("net: stmmac: Do not accept invalid MTU values")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87b0f983f6 ]
To rehash a previous explanation given in commit 1c44ce560b ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.
The configuration for this native VLAN is driven in 2 ways:
- Set the egress port rewriter to strip the VLAN tag for the native
VID (as it is egress-untagged, after all).
- Configure the ingress port to drop untagged and priority-tagged
traffic, if there is no native VLAN. The intention of this setting is
that a trunk port with no native VLAN should not accept untagged
traffic.
Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.
But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
- Native VLAN of the port - its value is held in port->vid.
- VLAN awareness state of the port - currently there are some issues
here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
0. The driver configures a pvid of zero for each port, when in
standalone mode. While the bridge configures a default_pvid of 1 for
each port that gets added as a slave to it.
1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
The VLAN-filtering-dependent portion of the native VLAN
configuration is done, considering that the native VLAN is 0.
2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
untagged=true. The native VLAN changes to 1 (change which gets
propagated to hardware).
3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
VLAN-filtering-dependent portion of the native VLAN configuration,
for the new native VLAN of 1. One can notice that after toggling "ip
link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
type bridge vlan_filtering 1", the new native VLAN finally makes it
through and untagged traffic finally starts flowing again. But
obviously that shouldn't be needed.
So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.
*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
- Ocelot: ocelot_port_private->vlan_aware
- Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.
Fixes: 97bb69e1e3 ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7482d9cb5b ]
Cited patch missed to extract PCI pf number accurately for PF and VF
port flavour. It considered PCI device + function number.
Due to this, device having non zero device number shown large pfnum.
Hence, use only PCI function number; to avoid similar errors, derive
pfnum one time for all port flavours.
Fixes: f60f315d33 ("net/mlx5e: Register devlink ports for physical link, PCI PF, VFs")
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70f478ca08 ]
Current value of nest_level, assigned from net_device lower_level value,
does not reflect the actual number of vlan headers, needed to pop.
For ex., if we have untagged ingress traffic sended over vlan devices,
instead of one pop action, driver will perform two pop actions.
To fix that, calculate nest_level as difference between vlan device and
parent device lower_levels.
Fixes: f3b0a18bb6 ("net: remove unnecessary variables and callback")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d518691cbd ]
The driver uses __napi_schedule_irqoff() which is fine as long as it is
invoked with disabled interrupts by everybody. Since the commit
mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq
context. This may lead to list corruption if another driver uses
__napi_schedule_irqoff() in IRQ context.
Use __napi_schedule() which safe to use from IRQ and softirq context.
Fixes: 85b85c8534 ("amd-xgbe: Re-issue interrupt if interrupt status not cleared")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2abb579238 upstream.
This allows the changelink operation to succeed if the mux_id was
specified as an argument. Note that the mux_id must match the
existing mux_id of the rmnet device or should be an unused mux_id.
Fixes: 1dc49e9d16 ("net: rmnet: do not allow to change mux id if mux id is duplicated")
Reported-and-tested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bcaeb886ad ]
In qlcnic_83xx_get_reset_instruction_template, the variable
of null test is bad, so correct it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50e0d28d38 ]
cxgb4_ptp_fineadjtime() doesn't pass the signedness of offset delta
in FW_PTP_CMD. Fix it by passing correct sign.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0da7c322f1 ]
the second input parameter of wait_for_completion_timeout should
be jiffies instead of millisecond
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33f15da216 ]
add read barrier in driver code to keep from reading other fileds
in dma memory which is writable for hw until we have verified the
memory is valid for driver
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 614eaa943e ]
should disable eq irq before freeing it, must clear event queue
depth in hw before freeing relevant memory to avoid illegal
memory access and update consumer idx to avoid invalid interrupt
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96758117dc ]
it's unreliable for fw to check whether IO is stopped, so driver
wait for enough time to ensure IO process is done in hw before
freeing resources
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b317538c47 ]
printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix,
it causes a build error when there is no variable
arguments(e.g. only fmt is specified.).
Signed-off-by: Zheng Wei <wei.zheng@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc191af1bb ]
Not every stmmac based platform makes use of the eth_wake_irq or eth_lpi
interrupts. Use the platform_get_irq_byname_optional variant for these
interrupts, so no error message is displayed, if they can't be found.
Rather print an information to hint something might be wrong to assist
debugging on platforms which use these interrupts.
Signed-off-by: Markus Fuchs <mklntf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95099c569a ]
There has been a number of reports that using SG/TSO on different chip
versions results in tx timeouts. However for a lot of people SG/TSO
works fine. Therefore disable both features by default, but allow users
to enable them. Use at own risk!
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ccfc569347 ]
The handler for FLOW_ACTION_VLAN_MANGLE ends by returning whatever the
lower-level function that it calls returns. If there are more actions lined
up after this action, those are never offloaded. Fix by only bailing out
when the called function returns an error.
Fixes: a150201a70 ("mlxsw: spectrum: Add support for vlan modify TC action")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e1221acf6 ]
Commit 9463c44559 ("net: stmmac: dwmac1000: Clear unused address
entries") cleared the unused mac address entries, but introduced an
out-of bounds mac address register programming bug -- After setting
the secondary unicast mac addresses, the "reg" value has reached
netdev_uc_count() + 1, thus we should only clear address entries
if (addr < perfect_addr_number)
Fixes: 9463c44559 ("net: stmmac: dwmac1000: Clear unused address entries")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41aa8561ca ]
cxgb4_update_mac_filt() earlier requests firmware to add a new MAC
address into MPS TCAM. The MPS TCAM index returned by firmware is
stored in pi->xact_addr_filt. However, the saved MPS TCAM index gets
overwritten again with the return value of cxgb4_update_mac_filt(),
which is wrong.
When trying to update to another MAC address later, the wrong MPS TCAM
index is sent to firmware, which causes firmware to return error,
because it's not the same MPS TCAM index that firmware had sent
earlier to driver.
So, fix by removing the wrong overwrite being done after call to
cxgb4_update_mac_filt().
Fixes: 3f8cfd0d95 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Signed-off-by: Herat Ramani <herat@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f28ca65efa upstream.
Fix to match the HW spec: TRACKING state is 1, SEARCHING is 2.
No real issue for now, as these values are not currently used.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8262e6f9b1 upstream.
This patch reverts 5829210483 ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 5829210483 ("net: ks8851-ml: Fix 16-bit IO operation")
Fixes: edacb098ea ("net: ks8851-ml: Fix 16-bit data access")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e8c339b49 upstream.
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f325937735 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3cc008bf6 ]
This patch fixes an off-by-one error in strncpy size argument in
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in:
strncmp(opt, "eee_timer:", 6)
the passed string literal: "eee_timer:" has 10 bytes (without the NULL
byte) and the passed size argument is 6. As a result, the logic will
also accept other, malformed strings, e.g. "eee_tiXXX:".
This bug doesn't seem to have any security impact since its present in
module's cmdline parsing code.
Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7395f62d95 ]
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2860:9: warning:
converting the result of '?:' with integer constants to a boolean always
evaluates to 'true' [-Wtautological-constant-compare]
return DPAA_FD_DATA_ALIGNMENT ? ALIGN(headroom,
^
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:131:34: note: expanded
from macro 'DPAA_FD_DATA_ALIGNMENT'
\#define DPAA_FD_DATA_ALIGNMENT (fman_has_errata_a050385() ? 64 : 16)
^
1 warning generated.
This was exposed by commit 3c68b8fffb ("dpaa_eth: FMan erratum A050385
workaround") even though it appears to have been an issue since the
introductory commit 9ad1a37493 ("dpaa_eth: add support for DPAA
Ethernet") since DPAA_FD_DATA_ALIGNMENT has never been able to be zero.
Just replace the whole boolean expression with the true branch, as it is
always been true.
Link: https://github.com/ClangBuiltLinux/linux/issues/928
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d7195a026 ]
The ibmvnic driver does not check the device state when the device
is removed. If the device is removed while a device reset is being
processed, the remove may free structures needed by the reset,
causing an oops.
Fix this by checking the device state before processing device remove.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 404402abd5 ]
The mask value is provided as 64 bit and has to be casted in
either 32 or 16 bit. On big endian systems the wrong half was
casted which resulted in an all zero mask.
Fixes: 2b64beba02 ("net/mlx5e: Support header re-write of partial fields in TC pedit offload")
Signed-off-by: Sebastian Hense <sebastian.hense1@ibm.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56917766de ]
We have an off-by-1 issue in the TCP seq comparison.
The last sequence number that belongs to the TCP packet's payload
is not "start_seq + len", but one byte before it.
Fix it so the 'ends_before' is evaluated properly.
This fixes a bug that results in error completions in the
kTLS HW offload flows.
Fixes: ffbd9ca94e ("net/mlx5e: kTLS, Fix corner-case checks in TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 187a9830c9 ]
For non-fatal syndromes like LOCAL_LENGTH_ERR, recovery shouldn't be
triggered. In these scenarios, the RQ is not actually in ERR state.
This misleads the recovery flow which assumes that the RQ is really in
error state and no more completions arrive, causing crashes on bad page
state.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e239c6d686 ]
In striding RQ mode, the buffers of an RX WQE are first
prepared and posted to the HW using a UMR WQEs via the ICOSQ.
We maintain the state of these in-progress WQEs in the RQ
SW struct.
In the flow of ICOSQ recovery, the corresponding RQ is not
in error state, hence:
- The buffers of the in-progress WQEs must be released
and the RQ metadata should reflect it.
- Existing RX WQEs in the RQ should not be affected.
For this, wrap the dealloc of the in-progress WQEs in
a function, and use it in the ICOSQ recovery flow
instead of mlx5e_free_rx_descs().
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39369fd536 ]
When resetting the RQ (moving RQ state from RST to RDY), the driver
resets the WQ's SW metadata.
In striding RQ mode, we maintain a field that reflects the actual
expected WQ head (including in progress WQEs posted to the ICOSQ).
It was mistakenly not reset together with the WQ. Fix this here.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1de0306c3a ]
Add number of WQEBBs (WQE's Basic Block) to WQE info struct. Set the
number of WQEBBs on WQE post, and increment the consumer counter (cc)
on completion.
In case of error completions, the cc was mistakenly not incremented,
keeping a gap between cc and pc (producer counter). This failed the
recovery flow on the ICOSQ from a CQE error which timed-out waiting for
the cc and pc to meet.
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dfdde1345b ]
last_keep_alive_jiffies is updated in probe and when a keep-alive
event is received. In case the driver times-out on a keep-alive event,
it has high chances of continuously timing-out on keep-alive events.
This is because when the driver recovers from the keep-alive-timeout reset
the value of last_keep_alive_jiffies is very old, and if a keep-alive
event is not received before the next timer expires, the value of
last_keep_alive_jiffies will cause another keep-alive-timeout reset
and so forth in a loop.
Solution:
Update last_keep_alive_jiffies whenever the device is restored after
reset.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30623e1ed1 ]
Rx req_id is an index in struct ena_eth_io_rx_cdesc_base.
The driver should validate that the Rx req_id it received from
the device is in range [0, ring_size -1]. Failure to do so could
yield to potential memory access violoation.
The validation was mistakenly done when refilling
the Rx submission queue and not in Rx completion queue.
Fixes: ad974baef2 ("net: ena: add support for out of order rx buffers refill")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e02ae6ed51 ]
Bug:
In short the main issue is caused by the fact that the number of queues
is changed using ethtool after ena_probe() has been called and before
ena_up() was executed. Here is the full scenario in detail:
* ena_probe() is called when the driver is loaded, the driver is not up
yet at the end of ena_probe().
* The number of queues is changed -> io_queue_count is changed as well -
ena_up() is not called since the "dev_was_up" boolean in
ena_update_queue_count() is false.
* ena_up() is called by the kernel (it's called asynchronously some
time after ena_probe()). ena_setup_io_intr() is called by ena_up() and
it uses io_queue_count to get the suitable irq lines for each msix
vector. The function ena_request_io_irq() is called right after that
and it uses msix_vecs - This value only changes during ena_probe() and
ena_restore() - to request the irq vectors. This results in "Failed to
request I/O IRQ" error for i > io_queue_count.
Numeric example:
* After ena_probe() io_queue_count = 8, msix_vecs = 9.
* The number of queues changes to 4 -> io_queue_count = 4, msix_vecs = 9.
* ena_up() is executed for the first time:
** ena_setup_io_intr() inits the vectors only up to io_queue_count.
** ena_request_io_irq() calls request_irq() and fails for i = 5.
How to reproduce:
simply run the following commands:
sudo rmmod ena && sudo insmod ena.ko;
sudo ethtool -L eth1 combined 3;
Fix:
Use ENA_MAX_MSIX_VEC(adapter->num_io_queues + adapter->xdp_num_queues)
instead of adapter->msix_vecs. We need to take XDP queues into
consideration as they need to have msix vectors assigned to them as well.
Note that the XDP cannot be attached before the driver is up and running
but in XDP mode the issue might occur when the number of queues changes
right after a reset trigger.
The ENA_MAX_MSIX_VEC simply adds one to the argument since the first msix
vector is reserved for management queue.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
