For hs400(es) mode, the 'hs400-ds-delay' is typically configured in the
dts. However, some projects may only define 'mediatek,hs400-ds-dly3',
which can lead to initialization failures in hs400es mode. CMD13 reported
response crc error in the mmc_switch_status() just after switching to
hs400es mode.
[ 1.914038][ T82] mmc0: mmc_select_hs400es failed, error -84
[ 1.914954][ T82] mmc0: error -84 whilst initialising MMC card
Currently, the hs400_ds_dly3 value is set within the tuning function. This
means that the PAD_DS_DLY3 field is not configured before tuning process,
which is the reason for the above-mentioned CMD13 response crc error.
Move the PAD_DS_DLY3 field configuration into msdc_prepare_hs400_tuning(),
and add a value check of hs400_ds_delay to prevent overwriting by zero when
the 'hs400-ds-delay' is not set in the dts. In addition, since hs400(es)
only tune the PAD_DS_DLY1, the PAD_DS_DLY2_SEL bit should be cleared to
bypass it.
Fixes: c4ac38c653 ("mmc: mtk-sd: Add HS400 online tuning support")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250123092644.7359-1-andy-ld.lu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 941a7abd46.
This commit uses presence of device-tree properties vmmc-supply and
vqmmc-supply for deciding whether to enable a quirk affecting timing of
clock and data.
The intention was to address issues observed with eMMC and SD on AM62
platforms.
This new quirk is however also enabled for AM64 breaking microSD access
on the SolidRun HimmingBoard-T which is supported in-tree since v6.11,
causing a regression. During boot microSD initialization now fails with
the error below:
[ 2.008520] mmc1: SDHCI controller on fa00000.mmc [fa00000.mmc] using ADMA 64-bit
[ 2.115348] mmc1: error -110 whilst initialising SD card
The heuristics for enabling the quirk are clearly not correct as they
break at least one but potentially many existing boards.
Revert the change and restore original behaviour until a more
appropriate method of selecting the quirk is derived.
Fixes: 941a7abd46 ("mmc: sdhci_am654: Add sdhci_am654_start_signal_voltage_switch")
Closes: https://lore.kernel.org/linux-mmc/a70fc9fc-186f-4165-a652-3de50733763a@solid-run.com/
Cc: stable@vger.kernel.org
Signed-off-by: Josua Mayer <josua@solid-run.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250127-am654-mmc-regression-v2-1-9bb39fb12810@solid-run.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull MMC updates from Ulf Hansson:
"MMC core:
- Share a helper to convert from crypto_profile to mmc_host
- Respect quirk_max_rate for non-UHS SDIO card too
MMC host:
- Add DT bindings for the mmc-slot
- Clarify DT bindings for the mmc-controller
- bcm2835: Add support for system-wide suspend/resume PM
- dw_mmc-exynos: Add support for the exynos8895 variant
- meson-mx-sdio: Convert DT bindings to dtschema
- mtk-sd: Fixup use of two register ranges
- mtk-sd: Add support for ignoring cmd response CRC
- sdhci-esdhc-imx: enable 'SDHCI_QUIRK_NO_LED' quirk for S32G
- sdhci-msm: Correctly set the load for the regulator
- sdhci-msm: Convert to use custom crypto profile
- sdhci-of-at91: Add support for the microchip sama7d65 variant"
* tag 'mmc-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (25 commits)
mmc: sdhci-msm: Correctly set the load for the regulator
mmc: hi3798mv200: Use syscon_regmap_lookup_by_phandle_args
mmc: Use of_property_present() for non-boolean properties
dt-bindings: mmc: samsung,exynos-dw-mshc: add specific compatible for exynos8895
mmc: sdhci-msm: convert to use custom crypto profile
mmc: crypto: add mmc_from_crypto_profile()
mmc: mtk-sd: Limit getting top_base to SoCs that require it
dt-bindings: mmc: mtk-sd: Document compatibles that need two register ranges
mmc: sdhci-acpi: Use devm_platform_ioremap_resource()
mmc: sdhci-acpi: Remove not so useful error message
dt-bindings: mmc: convert amlogic,meson-mx-sdio.txt to dtschema
dt-bindings: mmc: document mmc-slot
dt-bindings: mmc: controller: remove '|' when not needed
dt-bindings: mmc: controller: move properties common with slot out to mmc-controller-common
dt-bindings: mmc: controller: clarify the address-cells description
mmc: bcm2835: add suspend/resume pm support
dt-bindings: Drop Bhupesh Sharma from maintainers
mmc: core: don't include 'pm_wakeup.h' directly
mmc: mtk-sd: Add support for ignoring cmd response CRC
mmc: core: Introduce the MMC_RSP_R1B_NO_CRC response
...
Pull block updates from Jens Axboe:
- NVMe pull requests via Keith:
- Target support for PCI-Endpoint transport (Damien)
- TCP IO queue spreading fixes (Sagi, Chaitanya)
- Target handling for "limited retry" flags (Guixen)
- Poll type fix (Yongsoo)
- Xarray storage error handling (Keisuke)
- Host memory buffer free size fix on error (Francis)
- MD pull requests via Song:
- Reintroduce md-linear (Yu Kuai)
- md-bitmap refactor and fix (Yu Kuai)
- Replace kmap_atomic with kmap_local_page (David Reaver)
- Quite a few queue freeze and debugfs deadlock fixes
Ming introduced lockdep support for this in the 6.13 kernel, and it
has (unsurprisingly) uncovered quite a few issues
- Use const attributes for IO schedulers
- Remove bio ioprio wrappers
- Fixes for stacked device atomic write support
- Refactor queue affinity helpers, in preparation for better supporting
isolated CPUs
- Cleanups of loop O_DIRECT handling
- Cleanup of BLK_MQ_F_* flags
- Add rotational support for null_blk
- Various fixes and cleanups
* tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux: (106 commits)
block: Don't trim an atomic write
block: Add common atomic writes enable flag
md/md-linear: Fix a NULL vs IS_ERR() bug in linear_add()
block: limit disk max sectors to (LLONG_MAX >> 9)
block: Change blk_stack_atomic_writes_limits() unit_min check
block: Ensure start sector is aligned for stacking atomic writes
blk-mq: Move more error handling into blk_mq_submit_bio()
block: Reorder the request allocation code in blk_mq_submit_bio()
nvme: fix bogus kzalloc() return check in nvme_init_effects_log()
md/md-bitmap: move bitmap_{start, end}write to md upper layer
md/raid5: implement pers->bitmap_sector()
md: add a new callback pers->bitmap_sector()
md/md-bitmap: remove the last parameter for bimtap_ops->endwrite()
md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()
md: Replace deprecated kmap_atomic() with kmap_local_page()
md: reintroduce md-linear
partitions: ldm: remove the initial kernel-doc notation
blk-cgroup: rwstat: fix kernel-doc warnings in header file
blk-cgroup: fix kernel-doc warnings in header file
nbd: fix partial sending
...
Qualcomm regulator supports two power supply modes: HPM and LPM.
Currently, the sdhci-msm.c driver does not set the load to adjust
the current for eMMC and SD. If the regulator dont't set correct
load in LPM state, it will lead to the inability to properly
initialize eMMC and SD.
Set the correct regulator current for eMMC and SD to ensure that the
device can work normally even when the regulator is in LPM.
Signed-off-by: Yuanjie Yang <quic_yuanjiey@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250114083514.258379-1-quic_yuanjiey@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/all/20250111185410.183896-1-krzysztof.kozlowski@linaro.org>/
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BLK_MQ_F_SHOULD_MERGE is set for all tag_sets except those that purely
process passthrough commands (bsg-lib, ufs tmf, various nvme admin
queues) and thus don't even check the flag. Remove it to simplify the
driver interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241219060214.1928848-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As is being done in ufs-qcom, make the sdhci-msm driver override the
full crypto profile rather than "just" key programming and eviction.
This makes it much more straightforward to add support for
hardware-wrapped inline encryption keys. It also makes it easy to pass
the original blk_crypto_key down to qcom_ice_program_key() once it is
updated to require the key in that form.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Message-ID: <20241213041958.202565-8-ebiggers@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.13-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.14.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the mtk-sd driver tries to get and map the second register
base, named top_base in the code, regardless of whether the SoC model
actually has it or not. This produces confusing big error messages on
the platforms that don't need it:
mtk-msdc 11260000.mmc: error -EINVAL: invalid resource (null)
Limit it to the platforms that actually require it, based on their
device tree entries, and properly fail if it is missing.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20241210073212.3917912-3-wenst@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.13-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.14.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current implementation leaves pdev->dev as a wakeup source. Add a
device_init_wakeup(&pdev->dev, false) call in the .remove() function and
in the error path of the .probe() function.
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Fixes: 527f36f5ef ("mmc: mediatek: add support for SDIO eint wakup IRQ")
Cc: stable@vger.kernel.org
Message-ID: <20241203023442.2434018-1-joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current process flow does not handle MMC requests that are indicated
to ignore the command response CRC. For instance, cmd12 and cmd48 from
mmc_cqe_recovery() are marked to ignore CRC, but they are not matched to
the appropriate response type in msdc_cmd_find_resp(). As a result, they
are defaulted to 'MMC_RSP_NONE', which means no response is expected.
This commit applies the flag 'MMC_RSP_R1B_NO_CRC' to fix the response type
setting in msdc_cmd_find_resp() and adds the logic to ignore CRC in
msdc_cmd_done().
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Message-ID: <20241126125041.16071-3-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Vexia Edu Atla 10 tablet distributed to schools in the Spanish
Andalucía region has no ACPI fwnode associated with the SDHCI controller
for its microsd-slot and thus has no ACPI GPIO resource info.
This causes the following error to be logged and the slot to not work:
[ 10.572113] sdhci-pci 0000:00:12.0: failed to setup card detect gpio
Add a DMI quirk table for providing gpiod_lookup_tables with manually
provided CD GPIO info and use this DMI table to provide the CD GPIO info
on this tablet. This fixes the microsd-slot not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Message-ID: <20241118210049.311079-1-hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for Ultra Capacity SD cards (SDUC, 2TB to 128TB)
- Add support for Ultra High-Speed II SD cards (UHS-II)
- Use a reset control for pwrseq_simple
- Add SD card quirk for broken poweroff notification
- Use GFP_NOIO for SD ACMD22
MMC host:
- bcm2835: Introduce proper clock handling
- mtk-sd: Add support for the Host-Software-Queue interface
- mtk-sd: Add support for the mt7988/mt8196 variants
- mtk-sd: Fix a couple of error paths in ->probe()
- sdhci: Add interface to support UHS-II SD cards
- sdhci_am654: Fixup support for changing the signal voltage level
- sdhci-cadence: Add support for the Microchip PIC64GX variant
- sdhci-esdhc-imx: Add support for eMMC HW-reset
- sdhci-msm: Add support for the X1E80100/IPQ5424/SAR2130P/QCS615 variants
- sdhci-of-arasan: Add support for eMMC HW-reset
- sdhci-pci-gli: Add UHS-II support for the GL9767/GL9755 variants
MEMSTICK:
- A couple of minor updates"
* tag 'mmc-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (78 commits)
mmc: pwrseq_simple: Handle !RESET_CONTROLLER properly
mmc: mtk-sd: Fix MMC_CAP2_CRYPTO flag setting
mmc: mtk-sd: Fix error handle of probe function
mmc: core: Correction a warning caused by incorrect type in assignment for UHS-II
mmc: sdhci-esdhc-imx: Update esdhc sysctl dtocv bitmask
mmc: sdhci-esdhc-imx: Implement emmc hardware reset
mmc: core: Correct type in variable assignment for UHS-II
mmc: sdhci-uhs2: correction a warning caused by incorrect type in argument
mmc: sdhci-uhs2: Remove unnecessary variables
mmc: sdhci-uhs2: Correct incorrect type in argument
mmc: sdhci: Make MMC_SDHCI_UHS2 config symbol invisible
mmc: sdhci-uhs2: Remove unnecessary NULL check
mmc: core: Fix error paths for UHS-II card init and re-init
mmc: core: Add error handling of sd_uhs2_power_up()
mmc: core: Simplify sd_uhs2_power_up()
mmc: bcm2835: Introduce proper clock handling
mmc: bcm2835: Fix type of current clock speed
dt-bindings: mmc: Add sdhci compatible for QCS615
mmc: core: Use GFP_NOIO in ACMD22
dt-bindings: mmc: sdhci-msm: Add SAR2130P compatible
...
Pull block updates from Jens Axboe:
- NVMe updates via Keith:
- Use uring_cmd helper (Pavel)
- Host Memory Buffer allocation enhancements (Christoph)
- Target persistent reservation support (Guixin)
- Persistent reservation tracing (Guixen)
- NVMe 2.1 specification support (Keith)
- Rotational Meta Support (Matias, Wang, Keith)
- Volatile cache detection enhancment (Guixen)
- MD updates via Song:
- Maintainers update
- raid5 sync IO fix
- Enhance handling of faulty and blocked devices
- raid5-ppl atomic improvement
- md-bitmap fix
- Support for manually defining embedded partition tables
- Zone append fixes and cleanups
- Stop sending the queued requests in the plug list to the driver
->queue_rqs() handle in reverse order.
- Zoned write plug cleanups
- Cleanups disk stats tracking and add support for disk stats for
passthrough IO
- Add preparatory support for file system atomic writes
- Add lockdep support for queue freezing. Already found a bunch of
issues, and some fixes for that are in here. More will be coming.
- Fix race between queue stopping/quiescing and IO queueing
- ublk recovery improvements
- Fix ublk mmap for 64k pages
- Various fixes and cleanups
* tag 'for-6.13/block-20241118' of git://git.kernel.dk/linux: (118 commits)
MAINTAINERS: Update git tree for mdraid subsystem
block: make struct rq_list available for !CONFIG_BLOCK
block/genhd: use seq_put_decimal_ull for diskstats decimal values
block: don't reorder requests in blk_mq_add_to_batch
block: don't reorder requests in blk_add_rq_to_plug
block: add a rq_list type
block: remove rq_list_move
virtio_blk: reverse request order in virtio_queue_rqs
nvme-pci: reverse request order in nvme_queue_rqs
btrfs: validate queue limits
block: export blk_validate_limits
nvmet: add tracing of reservation commands
nvme: parse reservation commands's action and rtype to string
nvmet: report ns's vwc not present
md/raid5: Increase r5conf.cache_name size
block: remove the ioprio field from struct request
block: remove the write_hint field from struct request
nvme: check ns's volatile write cache not present
nvme: add rotational support
nvme: use command set independent id ns if available
...
Merge the mmc fixes for v6.12-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.13.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The recent introduction of reset control in pwrseq_simple introduced
a regression for platforms without RESET_CONTROLLER support, because
devm_reset_control_get_optional_shared() would return NULL and make all
resets no-ops. Instead of enforcing this dependency, rely on this behavior
to determine reset support. As a benefit we can get the rid of the
use_reset flag.
Fixes: 73bf4b7381 ("mmc: pwrseq_simple: add support for one reset control")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Message-ID: <20241108130647.8281-1-wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the MMC_CAP2_CRYPTO flag is set by default for eMMC hosts.
However, this flag should not be set for hosts that do not support inline
encryption.
The 'crypto' clock, as described in the documentation, is used for data
encryption and decryption. Therefore, only hosts that are configured with
this 'crypto' clock should have the MMC_CAP2_CRYPTO flag set.
Fixes: 7b438d0377 ("mmc: mtk-sd: add Inline Crypto Engine clock control")
Fixes: ed299eda8f ("mmc: mtk-sd: fix devm_clk_get_optional usage")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Cc: stable@vger.kernel.org
Message-ID: <20241111085039.26527-1-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the probe function, it goes to 'release_mem' label and returns after
some procedure failure. But if the clocks (partial or all) have been
enabled previously, they would not be disabled in msdc_runtime_suspend,
since runtime PM is not yet enabled for this case.
That cause mmc related clocks always on during system suspend and block
suspend flow. Below log is from a SDCard issue of MT8196 chromebook, it
returns -ETIMEOUT while polling clock stable in the msdc_ungate_clock()
and probe failed, but the enabled clocks could not be disabled anyway.
[ 129.059253] clk_chk_dev_pm_suspend()
[ 129.350119] suspend warning: msdcpll is on
[ 129.354494] [ck_msdc30_1_sel : enabled, 1, 1, 191999939, ck_msdcpll_d2]
[ 129.362787] [ck_msdcpll_d2 : enabled, 1, 1, 191999939, msdcpll]
[ 129.371041] [ck_msdc30_1_ck : enabled, 1, 1, 191999939, ck_msdc30_1_sel]
[ 129.379295] [msdcpll : enabled, 1, 1, 383999878, clk26m]
Add a new 'release_clk' label and reorder the error handle functions to
make sure the clocks be disabled after probe failure.
Fixes: ffaea6ebfe ("mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling")
Fixes: 7a2fa8eed9 ("mmc: mtk-sd: use devm_mmc_alloc_host")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Message-ID: <20241107121215.5201-1-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It turns out that the Allwinner A100/A133 SoC only supports 8K DMA
blocks (13 bits wide), for both the SD/SDIO and eMMC instances.
And while this alone would make a trivial fix, the H616 falls back to
the A100 compatible string, so we have to now match the H616 compatible
string explicitly against the description advertising 64K DMA blocks.
As the A100 is now compatible with the D1 description, let the A100
compatible string point to that block instead, and introduce an explicit
match against the H616 string, pointing to the old description.
Also remove the redundant setting of clk_delays to NULL on the way.
Fixes: 3536b82e58 ("mmc: sunxi: add support for A100 mmc controller")
Cc: stable@vger.kernel.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Parthiban Nallathambi <parthiban@linumiz.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Message-ID: <20241107014240.24669-1-andre.przywara@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
NXP ESDHC supports setting data timeout using uSDHCx_SYS_CTRL register
DTOCV bits (bits 16-19).
Currently the driver accesses those bits by 32-bit write using
SDHCI_TIMEOUT_CONTROL (0x2E) defined in drivers/mmc/host/sdhci.h.
This is offset by two bytes relative to uSDHCx_SYS_CTRL (0x2C).
The driver also defines ESDHC_SYS_CTRL_DTOCV_MASK as first 4 bits, which
is correct relative to SDHCI_TIMEOUT_CONTROL but not relative to
uSDHCx_SYS_CTRL. The definition carrying control register in its name is
therefore inconsistent.
Update the bitmask definition for bits 16-19 to be correct relative to
control register base.
Update the esdhc_set_timeout function to set timeout value at control
register base, not timeout offset.
This solves a purely cosmetic problem.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241101-imx-emmc-reset-v3-2-184965eed476@solid-run.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
NXP ESDHC supports control of native emmc reset signal when pinmux is
set accordingly, using uSDHCx_SYS_CTRL register IPP_RST_N bit.
Documentation is available in NXP i.MX6Q Reference Manual.
Implement the hw_reset function in sdhci_ops asserting reset for at
least 1us and waiting at least 200us after deassertion.
Lower bounds are based on:
JEDEC Standard No. 84-B51, 6.15.10 H/W Reset Operation, page 159.
Upper bounds are chosen allowing flexibility to the scheduler.
Tested on SolidRun i.MX8DXL SoM with a scope, and confirmed that eMMC is
still accessible after boot:
- eMMC extcsd has RST_N_FUNCTION=0x01
- sdhc node has cap-mmc-hw-reset
- pinmux set for EMMC0_RESET_B
- Linux v5.15
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241101-imx-emmc-reset-v3-1-184965eed476@solid-run.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path didn't manage the removal of the allocated mmc_card
correctly. Let's fix this to avoid potential memory leaks.
While at it, move the assignment of host->card to slightly later in the
init process and drop also a somewhat silly dev_warn() when CMD8 fails.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241029131752.226764-4-ulf.hansson@linaro.org>
The custom sdhost controller on BCM2835 is feed by the critical VPU clock.
In preparation for PM suspend/resume support, add a proper clock handling
to the driver like in the other clock consumers (e.g. I2C).
Move the clock handling behind mmc_of_parse(), because it could return
with -EPROBE_DEFER and we want to minimize potential clock operation during
boot phase.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Message-ID: <20241025103621.4780-5-wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.12-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.13.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
