IEP driver supports both perout and pps signal generation
but perout feature is faulty with half-cooked support
due to some missing configuration. Remove perout
support from the driver and reject perout requests with
"not supported" error code.
Fixes: c1e0230eea ("net: ti: icss-iep: Add IEP driver")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250227092441.1848419-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an issue with one-step timestamp based on UDP/IP. The peer will
discard the sync packet because of the wrong UDP checksum. For ENETC v1,
the software needs to update the UDP checksum when updating the
originTimestamp field, so that the hardware can correctly update the UDP
checksum when updating the correction field. Otherwise, the UDP checksum
in the sync packet will be wrong.
Fixes: 7294380c52 ("enetc: support PTP Sync packet one-step timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-6-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Actually ENETC VFs do not support HWTSTAMP_TX_ONESTEP_SYNC because only
ENETC PF can access PMa_SINGLE_STEP registers. And there will be a crash
if VFs are used to test one-step timestamp, the crash log as follows.
[ 129.110909] Unable to handle kernel paging request at virtual address 00000000000080c0
[ 129.287769] Call trace:
[ 129.290219] enetc_port_mac_wr+0x30/0xec (P)
[ 129.294504] enetc_start_xmit+0xda4/0xe74
[ 129.298525] enetc_xmit+0x70/0xec
[ 129.301848] dev_hard_start_xmit+0x98/0x118
Fixes: 41514737ec ("enetc: add get_ts_info interface for ethtool")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250224111251.1061098-5-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have recently seen reports of lockdep circular lock dependency warnings
when loading the iAVF driver:
[ 1504.790308] ======================================================
[ 1504.790309] WARNING: possible circular locking dependency detected
[ 1504.790310] 6.13.0 #net_next_rt.c2933b2befe2.el9 Not tainted
[ 1504.790311] ------------------------------------------------------
[ 1504.790312] kworker/u128:0/13566 is trying to acquire lock:
[ 1504.790313] ffff97d0e4738f18 (&dev->lock){+.+.}-{4:4}, at: register_netdevice+0x52c/0x710
[ 1504.790320]
[ 1504.790320] but task is already holding lock:
[ 1504.790321] ffff97d0e47392e8 (&adapter->crit_lock){+.+.}-{4:4}, at: iavf_finish_config+0x37/0x240 [iavf]
[ 1504.790330]
[ 1504.790330] which lock already depends on the new lock.
[ 1504.790330]
[ 1504.790330]
[ 1504.790330] the existing dependency chain (in reverse order) is:
[ 1504.790331]
[ 1504.790331] -> #1 (&adapter->crit_lock){+.+.}-{4:4}:
[ 1504.790333] __lock_acquire+0x52d/0xbb0
[ 1504.790337] lock_acquire+0xd9/0x330
[ 1504.790338] mutex_lock_nested+0x4b/0xb0
[ 1504.790341] iavf_finish_config+0x37/0x240 [iavf]
[ 1504.790347] process_one_work+0x248/0x6d0
[ 1504.790350] worker_thread+0x18d/0x330
[ 1504.790352] kthread+0x10e/0x250
[ 1504.790354] ret_from_fork+0x30/0x50
[ 1504.790357] ret_from_fork_asm+0x1a/0x30
[ 1504.790361]
[ 1504.790361] -> #0 (&dev->lock){+.+.}-{4:4}:
[ 1504.790364] check_prev_add+0xf1/0xce0
[ 1504.790366] validate_chain+0x46a/0x570
[ 1504.790368] __lock_acquire+0x52d/0xbb0
[ 1504.790370] lock_acquire+0xd9/0x330
[ 1504.790371] mutex_lock_nested+0x4b/0xb0
[ 1504.790372] register_netdevice+0x52c/0x710
[ 1504.790374] iavf_finish_config+0xfa/0x240 [iavf]
[ 1504.790379] process_one_work+0x248/0x6d0
[ 1504.790381] worker_thread+0x18d/0x330
[ 1504.790383] kthread+0x10e/0x250
[ 1504.790385] ret_from_fork+0x30/0x50
[ 1504.790387] ret_from_fork_asm+0x1a/0x30
[ 1504.790389]
[ 1504.790389] other info that might help us debug this:
[ 1504.790389]
[ 1504.790389] Possible unsafe locking scenario:
[ 1504.790389]
[ 1504.790390] CPU0 CPU1
[ 1504.790391] ---- ----
[ 1504.790391] lock(&adapter->crit_lock);
[ 1504.790393] lock(&dev->lock);
[ 1504.790394] lock(&adapter->crit_lock);
[ 1504.790395] lock(&dev->lock);
[ 1504.790397]
[ 1504.790397] *** DEADLOCK ***
This appears to be caused by the change in commit 5fda3f3534 ("net: make
netdev_lock() protect netdev->reg_state"), which added a netdev_lock() in
register_netdevice.
The iAVF driver calls register_netdevice() from iavf_finish_config(), as a
final stage of its state machine post-probe. It currently takes the RTNL
lock, then the netdev lock, and then the device critical lock. This pattern
is used throughout the driver. Thus there is a strong dependency that the
crit_lock should not be acquired before the net device lock. The change to
register_netdevice creates an ABBA lock order violation because the iAVF
driver is holding the crit_lock while calling register_netdevice, which
then takes the netdev_lock.
It seems likely that future refactors could result in netdev APIs which
hold the netdev_lock while calling into the driver. This means that we
should not re-order the locks so that netdev_lock is acquired after the
device private crit_lock.
Instead, notice that we already release the netdev_lock prior to calling
the register_netdevice. This flow only happens during the early driver
initialization as we transition through the __IAVF_STARTUP,
__IAVF_INIT_VERSION_CHECK, __IAVF_INIT_GET_RESOURCES, etc.
Analyzing the places where we take crit_lock in the driver there are two
sources:
a) several of the work queue tasks including adminq_task, watchdog_task,
reset_task, and the finish_config task.
b) various callbacks which ultimately stem back to .ndo operations or
ethtool operations.
The latter cannot be triggered until after the netdevice registration is
completed successfully.
The iAVF driver uses alloc_ordered_workqueue, which is an unbound workqueue
that has a max limit of 1, and thus guarantees that only a single work item
on the queue is executing at any given time, so none of the other work
threads could be executing due to the ordered workqueue guarantees.
The iavf_finish_config() function also does not do anything else after
register_netdevice, unless it fails. It seems unlikely that the driver
private crit_lock is protecting anything that register_netdevice() itself
touches.
Thus, to fix this ABBA lock violation, lets simply release the
adapter->crit_lock as well as netdev_lock prior to calling
register_netdevice(). We do still keep holding the RTNL lock as required by
the function. If we do fail to register the netdevice, then we re-acquire
the adapter critical lock to finish the transition back to
__IAVF_INIT_CONFIG_ADAPTER.
This ensures every call where both netdev_lock and the adapter->crit_lock
are acquired under the same ordering.
Fixes: afc664987a ("eth: iavf: extend the netdev_lock usage")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If ice_ena_vfs() fails after calling ice_create_vf_entries(), it frees
all VFs without removing them from snapshot PF-VF mailbox list, leading
to list corruption.
Reproducer:
devlink dev eswitch set $PF1_PCI mode switchdev
ip l s $PF1 up
ip l s $PF1 promisc on
sleep 1
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/$PF1/device/sriov_numvfs
Trace (minimized):
list_add corruption. next->prev should be prev (ffff8882e241c6f0), but was 0000000000000000. (next=ffff888455da1330).
kernel BUG at lib/list_debug.c:29!
RIP: 0010:__list_add_valid_or_report+0xa6/0x100
ice_mbx_init_vf_info+0xa7/0x180 [ice]
ice_initialize_vf_entry+0x1fa/0x250 [ice]
ice_sriov_configure+0x8d7/0x1520 [ice]
? __percpu_ref_switch_mode+0x1b1/0x5d0
? __pfx_ice_sriov_configure+0x10/0x10 [ice]
Sometimes a KASAN report can be seen instead with a similar stack trace:
BUG: KASAN: use-after-free in __list_add_valid_or_report+0xf1/0x100
VFs are added to this list in ice_mbx_init_vf_info(), but only removed
in ice_free_vfs(). Move the removing to ice_free_vf_entries(), which is
also being called in other places where VFs are being removed (including
ice_free_vfs() itself).
Fixes: 8cd8a6b17d ("ice: move VF overflow message count into struct ice_mbx_vf_info")
Reported-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/PH0PR11MB50138B635F2E5CEB7075325D961F2@PH0PR11MB5013.namprd11.prod.outlook.com
Reviewed-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250224190647.3601930-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test XDP and HDS interaction. While at it add a test for using the IOCTL,
as that turned out to be the real culprit.
Testing bnxt:
# NETIF=eth0 ./ksft-net-drv/drivers/net/hds.py
KTAP version 1
1..12
ok 1 hds.get_hds
ok 2 hds.get_hds_thresh
ok 3 hds.set_hds_disable # SKIP disabling of HDS not supported by the device
ok 4 hds.set_hds_enable
ok 5 hds.set_hds_thresh_zero
ok 6 hds.set_hds_thresh_max
ok 7 hds.set_hds_thresh_gt
ok 8 hds.set_xdp
ok 9 hds.enabled_set_xdp
ok 10 hds.ioctl
ok 11 hds.ioctl_set_xdp
ok 12 hds.ioctl_enabled_set_xdp
# Totals: pass:11 fail:0 xfail:0 xpass:0 skip:1 error:0
and netdevsim:
# ./ksft-net-drv/drivers/net/hds.py
KTAP version 1
1..12
ok 1 hds.get_hds
ok 2 hds.get_hds_thresh
ok 3 hds.set_hds_disable
ok 4 hds.set_hds_enable
ok 5 hds.set_hds_thresh_zero
ok 6 hds.set_hds_thresh_max
ok 7 hds.set_hds_thresh_gt
ok 8 hds.set_xdp
ok 9 hds.enabled_set_xdp
ok 10 hds.ioctl
ok 11 hds.ioctl_set_xdp
ok 12 hds.ioctl_enabled_set_xdp
# Totals: pass:12 fail:0 xfail:0 xpass:0 skip:0 error:0
Netdevsim needs a sane default for tx/rx ring size.
ethtool 6.11 is needed for the --disable-netlink option.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250221025141.1132944-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the kernel is compiled without LED framework support the
rtl8366rb fails to build like this:
rtl8366rb.o: in function `rtl8366rb_setup_led':
rtl8366rb.c:953:(.text.unlikely.rtl8366rb_setup_led+0xe8):
undefined reference to `led_init_default_state_get'
rtl8366rb.c:980:(.text.unlikely.rtl8366rb_setup_led+0x240):
undefined reference to `devm_led_classdev_register_ext'
As this is constantly coming up in different randconfig builds,
bite the bullet and create a separate file for the offending
code, split out a header with all stuff needed both in the
core driver and the leds code.
Add a new bool Kconfig option for the LED compile target, such
that it depends on LEDS_CLASS=y || LEDS_CLASS=RTL8366RB
which make LED support always available when LEDS_CLASS is
compiled into the kernel and enforce that if the LEDS_CLASS
is a module, then the RTL8366RB driver needs to be a module
as well so that modprobe can resolve the dependencies.
Fixes: 32d6170054 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502070525.xMUImayb-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats calculations involve a RMW to add the stat update to the existing
value. This is currently not protected by any synchronization mechanism,
so data races are possible. Add a spinlock to protect the update. The
reader side could be protected using u64_stats, but we would still need
a spinlock for the update side anyway. And we always do an update
immediately before reading the stats anyway.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250220162950.95941-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 22600596b6 ("ipv4: give an IPv4 dev to blackhole_netdev")
IPv4 neighbors can be constructed on the blackhole net device, but they
are constructed with an output function (neigh_direct_output()) that
simply calls dev_queue_xmit(). The latter will transmit packets via
'skb->dev' which might not be the blackhole net device if dst_dev_put()
switched 'dst->dev' to the blackhole net device while another CPU was
using the dst entry in ip_output(), but after it already initialized
'skb->dev' from 'dst->dev'.
Specifically, the following can happen:
CPU1 CPU2
udp_sendmsg(sk1) udp_sendmsg(sk2)
udp_send_skb() [...]
ip_output()
skb->dev = skb_dst(skb)->dev
dst_dev_put()
dst->dev = blackhole_netdev
ip_finish_output2()
resolves neigh on dst->dev
neigh_output()
neigh_direct_output()
dev_queue_xmit()
This will result in IPv4 packets being sent without an Ethernet header
via a valid net device:
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on enp9s0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
22:07:02.329668 20:00:40:11:18:fb > 45:00:00:44:f4:94, ethertype Unknown
(0x58c6), length 68:
0x0000: 8dda 74ca f1ae ca6c ca6c 0098 969c 0400 ..t....l.l......
0x0010: 0000 4730 3f18 6800 0000 0000 0000 9971 ..G0?.h........q
0x0020: c4c9 9055 a157 0a70 9ead bf83 38ca ab38 ...U.W.p....8..8
0x0030: 8add ab96 e052 .....R
Fix by making sure that neighbors are constructed on top of the
blackhole net device with an output function that simply consumes the
packets, in a similar fashion to dst_discard_out() and
blackhole_netdev_xmit().
Fixes: 8d7017fd62 ("blackhole_netdev: use blackhole_netdev to invalidate dst entries")
Fixes: 22600596b6 ("ipv4: give an IPv4 dev to blackhole_netdev")
Reported-by: Florian Meister <fmei@sfs.com>
Closes: https://lore.kernel.org/netdev/20250210084931.23a5c2e4@hermes.local/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250220072559.782296-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The external PHY will undergo a soft reset twice during the resume process
when it wake up from suspend. The first reset occurs when the axienet
driver calls phylink_of_phy_connect(), and the second occurs when
mdio_bus_phy_resume() invokes phy_init_hw(). The second soft reset of the
external PHY does not reinitialize the internal PHY, which causes issues
with the internal PHY, resulting in the PHY link being down. To prevent
this, setting the mac_managed_pm flag skips the mdio_bus_phy_resume()
function.
Fixes: a129b41fe0 ("Revert "net: phy: dp83867: perform soft reset and retain established link"")
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250217055843.19799-1-nick.hu@sifive.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As explained in the previous patch, iterating for_each_netdev() and
gn->geneve_list during ->exit_batch_rtnl() could trigger ->dellink()
twice for the same device.
If CONFIG_DEBUG_LIST is enabled, we will see a list_del() corruption
splat in the 2nd call of geneve_dellink().
Let's remove for_each_netdev() in geneve_destroy_tunnels() and delegate
that part to default_device_exit_batch().
Fixes: 9593172d93 ("geneve: Fix use-after-free in geneve_find_dev().")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250217203705.40342-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix incorrect data offset read in the pd692x0_pi_get_pw_limit callback.
The issue was previously unnoticed as it was only used by the regulator
API and not thoroughly tested, since the PSE is mainly controlled via
ethtool.
The function became actively used by ethtool after commit 3e9dbfec49
("net: pse-pd: Split ethtool_get_status into multiple callbacks"),
which led to the discovery of this issue.
Fix it by using the correct data offset.
Fixes: a87e699c9d ("net: pse-pd: pd692x0: Enhance with new current limit and voltage read callbacks")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250217134812.1925345-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before this patch the NETDEV_XDP_ACT_NDO_XMIT XDP feature flag is set by
default as part of driver initialization, and is never cleared. However,
this flag differs from others in that it is used as an indicator for
whether the driver is ready to perform the ndo_xdp_xmit operation as
part of an XDP_REDIRECT. Kernel helpers
xdp_features_(set|clear)_redirect_target exist to convey this meaning.
This patch ensures that the netdev is only reported as a redirect target
when XDP queues exist to forward traffic.
Fixes: 39a7f4aa3e ("gve: Add XDP REDIRECT support for GQI-QPL format")
Cc: stable@vger.kernel.org
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20250214224417.1237818-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, after successfully flushing the xmit buffer to VIOS,
the tx_bytes stat was incremented by the length of the skb.
It is invalid to access the skb memory after sending the buffer to
the VIOS because, at any point after sending, the VIOS can trigger
an interrupt to free this memory. A race between reading skb->len
and freeing the skb is possible (especially during LPM) and will
result in use-after-free:
==================================================================
BUG: KASAN: slab-use-after-free in ibmvnic_xmit+0x75c/0x1808 [ibmvnic]
Read of size 4 at addr c00000024eb48a70 by task hxecom/14495
<...>
Call Trace:
[c000000118f66cf0] [c0000000018cba6c] dump_stack_lvl+0x84/0xe8 (unreliable)
[c000000118f66d20] [c0000000006f0080] print_report+0x1a8/0x7f0
[c000000118f66df0] [c0000000006f08f0] kasan_report+0x128/0x1f8
[c000000118f66f00] [c0000000006f2868] __asan_load4+0xac/0xe0
[c000000118f66f20] [c0080000046eac84] ibmvnic_xmit+0x75c/0x1808 [ibmvnic]
[c000000118f67340] [c0000000014be168] dev_hard_start_xmit+0x150/0x358
<...>
Freed by task 0:
kasan_save_stack+0x34/0x68
kasan_save_track+0x2c/0x50
kasan_save_free_info+0x64/0x108
__kasan_mempool_poison_object+0x148/0x2d4
napi_skb_cache_put+0x5c/0x194
net_tx_action+0x154/0x5b8
handle_softirqs+0x20c/0x60c
do_softirq_own_stack+0x6c/0x88
<...>
The buggy address belongs to the object at c00000024eb48a00 which
belongs to the cache skbuff_head_cache of size 224
==================================================================
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250214155233.235559-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using the Qualcomm X55 modem on the ThinkPad X13s, the kernel log is
constantly being filled with errors related to a "sequence number glitch",
e.g.:
[ 1903.284538] sequence number glitch prev=16 curr=0
[ 1913.812205] sequence number glitch prev=50 curr=0
[ 1923.698219] sequence number glitch prev=142 curr=0
[ 2029.248276] sequence number glitch prev=1555 curr=0
[ 2046.333059] sequence number glitch prev=70 curr=0
[ 2076.520067] sequence number glitch prev=272 curr=0
[ 2158.704202] sequence number glitch prev=2655 curr=0
[ 2218.530776] sequence number glitch prev=2349 curr=0
[ 2225.579092] sequence number glitch prev=6 curr=0
Internet connectivity is working fine, so this error seems harmless. It
looks like modem does not preserve the sequence number when entering low
power state; the amount of errors depends on how actively the modem is
being used.
A similar issue has also been seen on USB-based MBIM modems [1]. However,
in cdc_ncm.c the "sequence number glitch" message is a debug message
instead of an error. Apply the same to the mhi_wwan_mbim.c driver to
silence these errors when using the modem.
[1]: https://lists.freedesktop.org/archives/libmbim-devel/2016-November/000781.html
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250212-mhi-wwan-mbim-sequence-glitch-v1-1-503735977cbd@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a deadlock in pse_pi_get_current_limit and pse_pi_set_current_limit
caused by consecutive mutex_lock calls. One in the function itself and
another in pse_pi_get_voltage.
Resolve the issue by using the unlocked version of pse_pi_get_voltage
instead.
Fixes: e0a5e2bba3 ("net: pse-pd: Use power limit at driver side instead of current limit")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250212151751.1515008-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For successful XDP_TX and XDP_REDIRECT cases, the packet was received
successfully so update RX statistics. Use original received
packet length for that.
TX packets statistics are incremented on TX completion so don't
update it while TX queueing.
If xdp_convert_buff_to_frame() fails, increment tx_dropped.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Fixes: 8acacc40f7 ("net: ethernet: ti: am65-cpsw: Add minimal XDP support")
Link: https://patch.msgid.link/20250210-am65-cpsw-xdp-fixes-v1-2-ec6b1f7f1aca@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the XDP program doesn't result in XDP_PASS then we leak the
memory allocated by am65_cpsw_build_skb().
It is pointless to allocate SKB memory before running the XDP
program as we would be wasting CPU cycles for cases other than XDP_PASS.
Move the SKB allocation after evaluating the XDP program result.
This fixes the memleak. A performance boost is seen for XDP_DROP test.
XDP_DROP test:
Before: 460256 rx/s 0 err/s
After: 784130 rx/s 0 err/s
Fixes: 8acacc40f7 ("net: ethernet: ti: am65-cpsw: Add minimal XDP support")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://patch.msgid.link/20250210-am65-cpsw-xdp-fixes-v1-1-ec6b1f7f1aca@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-02-11 (idpf, ixgbe, igc)
For idpf:
Sridhar fixes a couple issues in handling of RSC packets.
Josh adds a call to set_real_num_queues() to keep queue count in sync.
For ixgbe:
Piotr removes missed IS_ERR() removal when ERR_PTR usage was removed.
For igc:
Zdenek Bouska fixes reporting of Rx timestamp with AF_XDP.
Siang sets buffer type on empty frame to ensure proper handling.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Set buffer type for empty frames in igc_init_empty_frame
igc: Fix HW RX timestamp when passed by ZC XDP
ixgbe: Fix possible skb NULL pointer dereference
idpf: call set_real_num_queues in idpf_open
idpf: record rx queue in skb for RSC packets
idpf: fix handling rsc packet with a single segment
====================
Link: https://patch.msgid.link/20250211214343.4092496-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We should not be configuring the PHYs clock-stop settings unless the
MAC supports phylink managed EEE. Make this dependent on MAC support.
This was noticed in a suspicious RCU usage report from the kernel
test robot (the suspicious RCU usage due to calling phy_detach()
remains unaddressed, but is triggered by the error this was
generating.)
Fixes: 03abf2a7c6 ("net: phylink: add EEE management")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1tgjNn-003q0w-Pw@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes HW RX timestamp in the following scenario:
- AF_PACKET socket with enabled HW RX timestamps is created
- AF_XDP socket with enabled zero copy is created
- frame is forwarded to the BPF program, where the timestamp should
still be readable (extracted by igc_xdp_rx_timestamp(), kfunc
behind bpf_xdp_metadata_rx_timestamp())
- the frame got XDP_PASS from BPF program, redirecting to the stack
- AF_PACKET socket receives the frame with HW RX timestamp
Moves the skb timestamp setting from igc_dispatch_skb_zc() to
igc_construct_skb_zc() so that igc_construct_skb_zc() is similar to
igc_construct_skb().
This issue can also be reproduced by running:
# tools/testing/selftests/bpf/xdp_hw_metadata enp1s0
When a frame with the wrong port 9092 (instead of 9091) is used:
# echo -n xdp | nc -u -q1 192.168.10.9 9092
then the RX timestamp is missing and xdp_hw_metadata prints:
skb hwtstamp is not found!
With this fix or when copy mode is used:
# tools/testing/selftests/bpf/xdp_hw_metadata -c enp1s0
then RX timestamp is found and xdp_hw_metadata prints:
found skb hwtstamp = 1736509937.852786132
Fixes: 069b142f58 ("igc: Add support for PTP .getcyclesx64()")
Signed-off-by: Zdenek Bouska <zdenek.bouska@siemens.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Bezdeka <florian.bezdeka@siemens.com>
Reviewed-by: Song Yoong Siang <yoong.siang.song@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
