To maintain backward compatibility with older firmware versions, introduce a
new feature bit, ATH12K_FW_FEATURE_MLO, to identify whether the firmware
supports MLO. If the firmware-X.bin does not have this bit advertised in the
feature, then MLO capability in the host will be disabled.
This applies only for QCN9274 chipsets.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the Inter Multi-Link Operation, the primary device is expected to receive
the partner device buffer. Therefore, each device initializes the partner
device buffer in their cmem configuration. So add a helper function to
initialize the partner device buffer in their cmem configuration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of multi device group abstraction, host has to exchange the multi-link
operation commands such as setup and ready to firmware before registering the
device group to mac80211.
The multi-link operation commands - setup, ready and teardown are necessary for
many commands such as WMI_PEER_ASSOC_CMD, WMI_BCN_TMPL_CMD in case of
multi-link interfaces.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, a single device is part of the device group abstraction. However,
for multi-link operations, multiple devices need to be combined. This
multi-device grouping is done via WSI (WLAN Serial Interface), which is
described in the Device Tree. Information about different WSI groups and the
number of devices involved in each group can be parsed from the Device Tree.
Add changes to parse the Device Tree and determine WSI information, such as the
different WSI groups and the number of devices per WSI group. Assign WSI index
zero to the WSI controller device (to synchronize the clock among the devices
within the WSI group), and increment the WSI index of each device in the order
of the WSI connection.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, during mac80211 allocate and register single device is
considered for the registration. But, in future, during multi device
group abstraction is introduced, all the devices has to be combined
together as a single abstraction and then hardware should be allocated.
All the devices in the group should be combined together only if it
supports inter device mlo capability. The decision of whether to combine
the devices or not can be based on the mlo capability flag in
ath12k_hw_group.
By default, mlo_capable flag in the group would be set as false. During
QMI PHY capability exchange, only when we have more than one chip in the
group or if one chip, then that chip supports inter MLO, then mlo_capable
flag in the group will be enabled.
Add changes to introduce mlo_capable flag for device group and refactor
ath12k_mac_hw_allocate() api based on device group (ag) rather than
device (ab).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
QMI host capability has the information regarding MLO parameters such as
device_id, MLO capability, group id and the information of each devices
involved in the group and sent immediately on QMI server arrive event.
Currently, only one device is involved in the group and hence, single
device information is sent as part of MLO capability of host.
But, in future when multi device group abstraction is introduced, host
should send all the device information involved in the group as part
of QMI MLO host capability rather than single device. Hence, sending
QMI host capability immediately on server arrive of a device might not
be ideal for multi device group abstraction as the details of other
devices in the group would not be available.
Hence, once QMI server arrive event is received, request for QMI PHY
capabilities of device, and defer the host capability send for that device.
After QMI PHY capability is received for all the devices in the group
trigger the host capability event for the deferred devices in the group.
Hence, add changes to defer the QMI host capability event until the device
group is ready and then resume the QMI exchange for all the device with
host capabilities.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, hardware abstractions (ah) of different radio bands are tightly
coupled to a single device (ab). But, with hardware device group abstraction
(ag), multiple radios across different devices in a group can form different
combinations of hardware abstractions (ah) within the group. Hence, the mapping
between ah to ab can be removed and instead it can be mapped with struct
ath12k_hw_group (ag).
Current mapping between struct ath12k_hw (ah), struct ath12k_base (ab) and struct
ath12k_hw_group (ag):
+------------------------------------------------+
| +-------------------------------------+ |
| | +---------------+ +---------------+ | |
| | |ath12k_hw (ah) | |ath12k_hw (ah) | | |
| | +---------------+ +---------------+ | |
| | | |
| | +-----------+ | +-----------+ | |
| | | ar (2GHz) | | | ar (5GHz) | | |
| | +-----------+ | +-----------+ | |
| | Dual band device-1 (ab) | |
| +-------------------------------------+ |
| ath12k_hw_group (ag) based on group id |
+------------------------------------------------+
After hardware device group abstraction moving ah array out of ab to ag:
+----------------------------------------------+
| +---------------+ +---------------+ |
| |ath12k_hw (ah) | |ath12k_hw (ah) | |
| +---------------+ +---------------+ |
| +-------------------------------------+ |
| | +-----------+ +-----------+ | |
| | | ar (2GHz) | | ar (5GHz) | | |
| | +-----------+ +-----------+ | |
| | Dual band device-1 (ab) | |
| +-------------------------------------+ |
| ath12k_hw_group (ag) based on group id |
+----------------------------------------------+
This decoupling of struct ath12k_hw (ah) from struct ath12k_base (ab) and
mapping it to struct ath12k_hw_group (ag) will help in forming different
combinations of multi-link devices.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, mac allocate/register and core_pdev_create are initiated immediately
when QMI firmware ready event is received for a particular device. With
hardware device group abstraction, QMI firmware ready event can be received
simultaneously for different devices in the group and so, it should not be
registered immediately rather it has to be deferred until all devices in the
group has received QMI firmware ready.
To handle this, refactor the code of core start to have registering within
ath12k_core_hw_group_start() and unregistering in ath12k_core_hw_group_stop().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, single device is probed, and once firmware is ready, the device
is registered to mac80211. For Multi-Link Operation, different bands of
different devices or same device are part of a single wiphy and for
this, hardware device group abstraction is needed.
Hardware device group abstraction - when there are multiple devices (with
single radio or dual radio) that are connected by any means of interface
for communicating between them, then these devices can be combined
together as a single group using a group id to form a group abstraction
and register to mac80211.
The grouping information of multiple devices would be based on device tree
during device probe (will be implemented in future patches). If no such
information is available, then a single device will be part of group abstraction
and registered to mac80211, else multiple devices advertised in device tree are
combined and then registered to mac80211.
For device group abstraction, a base structure ath12k_hw_group (ag) and the
helpers are implemented. These helpers are used during device probe and mapping
the group to the devices involved.
An illustration of how multiple devices might be combined together in
future based on group id:
+------------------------------------------------------------------------+
| +-------------------------------------+ +-------------------+ |
| | +-----------+ | | +-----------+ | | +-----------+ | |
| | | ar (2GHz) | | | | ar (5GHz) | | | | ar (6GHz) | | |
| | +-----------+ | | +-----------+ | | +-----------+ | |
| | ath12k_base (ab) | | ath12k_base (ab) | |
| | (Dual band device) | | | |
| +-------------------------------------+ +-------------------+ |
| ath12k_hw_group (ag) based on group id |
+------------------------------------------------------------------------+
In the above representation, two devices are combined into single group
based on group id.
Add base code changes where single device would be part of a group with an
invalid group id forming an group abstraction. Multi device grouping will
be introduced in future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the mlo_capable_flags in ath12k_base is used to indicate whether
the chip supports inter (QCN9274) or intra (WCN7850) chip MLO. However, it’s
possible that the chip supports neither, especially with older firmware
versions. Additionally, if intra chip MLO is not supported, inter chip MLO will
also be non-functional. Therefore, having two separate flags for this is
unnecessary.
Therefore, rename this flag to single_chip_mlo_supp. At the same time convert
it into a bool data type. Also, get rid of the enums defined earlier.
For the QCN9274 family of chipsets, this will be set only when firmware
advertises the support during the QMI exchange.
For the WCN7850 family of chipsets, since the event is not supported,
assumption is made that single chip MLO is supported.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When hardware device group abstraction is introduced, the QMI firmware ready
event of different devices in a group can be received simultaneously. To
indicate the firmware ready event is completed for a particular device in a
group set a flag (ATH12K_FLAG_QMI_FW_READY_COMPLETE). This helps the upcoming
hardware recovery implementation for hardware device group abstraction.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-5-kvalo@kernel.org
Currently, one or more struct ath12k_hw is part of device (struct ath12k_base)
but in future, ath12k_hw would be part of device group (struct
ath12k_hw_group). Hence, num_hw under device would be moved to device group.
To facilitate above transition, add helper ath12k_get_num_hw() to get the
number of radios per device. In future, this helper will return the number of
radios in a device group.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-4-kvalo@kernel.org
Currently, one or more ath12k_hw is part of a device (struct ath12k_base) but
in future, it would be part of device group abstraction (struct
ath12k_hw_group), i.e., when multiple radios (ar) across different devices can
be combined together in a device group (struct ath12k_hw_group).
In order to facilitate the above transition, introduce helpers
ath12k_ab_to_ah() and ath12k_ab_set_ah() to get and set values of ath12k_hw
respectively.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-3-kvalo@kernel.org
In the upcoming hardware device group abstraction radios across different
devices can be grouped together to support multi-link operation and register as
a device group to mac80211.
Currently, ath12k_mac_allocate() and ath12k_mac_register() are part of
ath12k_core_start() and ath12k_core_pdev_create() respectively and are based on
per device (struct ath12k_base). These APIs can be decoupled and moved out to
ath12k_core_qmi_firmware_ready() itself. This refactor is helpful for device
group abstraction when mac80211 allocate and register will be changed from per
device (struct ath12k_base) to per device group (struct ath12k_hw_group).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-2-kvalo@kernel.org
To simplify locking for the next patches convert struct
ath12k::wmi_mgmt_tx_work to use wiphy_work. After this
ath12k_mgmt_over_wmi_tx_work() is called with wiphy_lock() taken. In
ath12k_core_suspend() we need to take wiphy_lock() because
ath12k_mac_wait_tx_complete() requires it.
Also add lockdep_assert_wiphy() to document when wiphy_lock() is held.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-2-kvalo@kernel.org
In case of firmware assert snapshot of firmware memory is essential for
debugging. Add firmware coredump collection support for PCI bus.
Collect RDDM and firmware paging dumps from MHI and pack them in TLV
format and also pack various memory shared during QMI phase in separate
TLVs. Add necessary header and share the dumps to user space using dev
coredump framework. Coredump collection is disabled by default and can
be enabled using menuconfig. Dump collected for a radio is 55 MB
approximately.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.2.1-00201-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240717085604.4131642-1-quic_ssreeela@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Switch from using driver specific ar->conf_mutex to wiphy->mtx. The benefits are:
* one lock less and simplified locking
* possibility to use wiphy_work_queue() without other locks
Most of the mac80211 ops are called within wiphy_lock(), most notable exception
being tx op. This can be checked with lockdep_assert_wiphy() from
net/mac80211/driver-ops.[ch] and I veried that by manually going through all
the ops in ath12k_ops which had lockdep_assert_wiphy().
The conversion was simple:
* All conf_mutex lock() and unlock() calls which
already were called under wiphy_lock() I replaced with
lockdep_assert_wiphy().
* The rest of conf_mutex calls I replaced with wiphy_lock() and wiphy_unlock().
* All lockdep_asset_held(conf_mutex) calls I replaced with
lockdep_assert_wiphy().
One exception was in ath12k_core_post_reconfigure_recovery() where the wiphy
lock needs to be taken before hw_mutex to avoid a lockdep warning.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241007165932.78081-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Implement basic WoW functionalities such as magic-packet, disconnect
and pattern. The logic is very similar to ath11k.
When WoW is configured, ath12k_core_suspend and ath12k_core_resume
are skipped (by checking ar->state) as we are not allowed to power
cycle firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-4-quic_bqiang@quicinc.com
Whenever firmware is crashed in split-phy below WARN_ON() triggered:
WARNING: CPU: 3 PID: 82 at net/mac80211/driver-ops.c:41 drv_stop+0xac/0xbc
Modules linked in: ath12k qmi_helpers
CPU: 3 PID: 82 Comm: kworker/3:2 Tainted: G D W 6.9.0-next-20240520-00113-gd981a3784e15 #39
Hardware name: Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C9 (DT)
Workqueue: events_freezable ieee80211_restart_work
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : drv_stop+0xac/0xbc
lr : ieee80211_stop_device+0x54/0x64
sp : ffff8000848dbb20
x29: ffff8000848dbb20 x28: 0000000000000790 x27: ffff000014d78900
x26: ffff000014d791f8 x25: ffff000007f0d9b0 x24: 0000000000000018
x23: 0000000000000001 x22: 0000000000000000 x21: ffff000014d78e10
x20: ffff800081dc0000 x19: ffff000014d78900 x18: ffffffffffffffff
x17: ffff7fffbca84000 x16: ffff800083fe0000 x15: ffff800081dc0b48
x14: 0000000000000076 x13: 0000000000000076 x12: 0000000000000001
x11: 0000000000000000 x10: 0000000000000a60 x9 : ffff8000848db980
x8 : ffff000000dddfc0 x7 : 0000000000000400 x6 : ffff800083b012d8
x5 : ffff800083b012d8 x4 : 0000000000000000 x3 : ffff000014d78398
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000014d78900
Call trace:
drv_stop+0xac/0xbc
ieee80211_stop_device+0x54/0x64
ieee80211_do_stop+0x5a0/0x790
ieee80211_stop+0x4c/0x178
__dev_close_many+0xb0/0x150
dev_close_many+0x88/0x130
dev_close.part.171+0x44/0x74
dev_close+0x1c/0x28
cfg80211_shutdown_all_interfaces+0x44/0xfc
ieee80211_restart_work+0xfc/0x14c
process_scheduled_works+0x18c/0x2dc
worker_thread+0x13c/0x314
kthread+0x118/0x124
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
The warning in question is from drv_stop():
if (WARN_ON(!local->started))
return;
The sequence of WARN_ON() is:
Thread 1:
-Firmware crash calls ath12k_core_reset().
-Call ieee80211_restart_hw() inside
ath12k_core_post_reconfigure_recovery() which schedules worker
for both hardware.
-Wait for completion of ab->recovery_start.
Thread 2 (worker thread):
-One hardware acquires rtnl_lock() inside ieee80211_restart_hw() and
calls ath12k_mac_wait_reconfigure() into ath12k_mac_op_start().
-Hardware is waiting for ab->reconfigure_complete but at this time
recovery_start_count value is 1 because another worker thread
(local->restart_work) is still waiting for rtnl_lock().
recovery_start_count is not equal to number of radios
(2 in split-phy). So ab->recovery_start complete does not set
due to this, thread 1 is still waiting and not able to perform
hif power down up and firmware reload.
-Wait timeout happens for ab->reconfigure_complete and comeback
to caller (ath12k_mac_op_start()) and sends WMI command to
crashed firmware and gets error.
-This returns error to drv_start() and local->started is set to false.
-Hardware calls cfg80211_shutdown_all_interfaces() after receiving error
inside ieee80211_restart_work() and goes to drv_stop(), here we trigger
WARN_ON as local->started is false.
To fix this issue call ieee80211_restart_hw() after firmware has been
reloaded. Now, each hardware can send WMI command to firmware
successfully. With this fix we don't need to wait for
ab->recovery_start completion so remove
ath12k_mac_wait_reconfigure().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 HW2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529034405.2863150-1-quic_aarasahu@quicinc.com
Currently ACPI notification handler is installed when driver loads and only
gets removed when driver unloads. During resume after firmware is reloaded,
ath12k tries to install it by default. Since it is installed already, ACPI
subsystem rejects it and returns an error:
[ 83.094206] ath12k_pci 0000:03:00.0: failed to install DSM notify callback: 7
Fix it by removing that handler when going to suspend. This also avoid any
possible ACPI call to firmware before firmware is reloaded/reinitialized.
Note ab->acpi also needs to be cleared in ath12k_acpi_stop() such that we
are in a clean state when ACPI structures are reinitialized in
ath12k_acpi_start().
Tested-on: WCN7850 HW2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 576771c9fa ("wifi: ath12k: ACPI TAS support")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240531024000.9291-1-quic_bqiang@quicinc.com
Currently for ath12k PCI devices, firmware could be running in one of
several execution environments, e.g., PBL, SBL and mission mode etc. Among
which PBL is the only stage where PCIe link negotiation could happen. So
normally firmware runs in PBL in order to be enumerated during system reboot.
However it might not work in kernel crash scenario: ath12k target is not
found after warm reboot from kernel crash. This is because when kernel crashes,
ath12k host does nothing to firmware. And during warm reboot, WLAN power
is sustained. So firmware is likely to keep running in mission mode throughout
the bootup process. As a result PCIe link is not established and thus target
not enumerated.
So add a handler in panic notification list for ath12k. When kernel crashes,
this handler gets called and tries to reset target to PBL state. Then PCIe
link negotiation could happen and target gets enumerated.
This change applies to all PCI devices including WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529021533.10861-1-quic_bqiang@quicinc.com
Smatch is throwing below warning:
Commit 692921ead8 ("wifi: ath12k: flush all packets before
suspend") leads to the following Smatch static checker warning:
drivers/net/wireless/ath/ath12k/core.c:58 ath12k_core_suspend()
warn: sleeping in atomic context
and also gives the reason:
drivers/net/wireless/ath/ath12k/core.c
48 int ret, i;
49
50 if (!ab->hw_params->supports_suspend)
51 return -EOPNOTSUPP;
52
53 rcu_read_lock();
^^^^^^^^^^^^^^^
Disables preemption.
54 for (i = 0; i < ab->num_radios; i++) {
55 ar = ath12k_mac_get_ar_by_pdev_id(ab, i);
56 if (!ar)
57 continue;
--> 58 ret = ath12k_mac_wait_tx_complete(ar);
^^^^^^^
Sleeping in atomic context.
59 if (ret) {
60 ath12k_warn(ab, "failed to wait tx complete: %d\n", ret);
61 rcu_read_unlock();
62 return ret;
63 }
64 }
65 rcu_read_unlock();
But it is weird that no warning on this in run time even with
CONFIG_DEBUG_ATOMIC_SLEEP=y. With some debug it is found that this is
because: when system goes to suspend, ath12k_mac_op_stop() gets called
where then in ath12k_mac_stop() ab->pdevs_active[ar->pdev_idx] is cleared.
This results in ath12k_mac_get_ar_by_pdev_id() always returning a NULL ar,
and thereby ath12k_mac_wait_tx_complete() never gets a chance to run.
Fix it by retrieving ar directly from ab->pdevs[].ar instead of using
ath12k_mac_get_ar_by_pdev_id(). Since ab->pdevs[].ar is set at boot time
and won't get cleared when suspend, ath12k_mac_wait_tx_complete() won't
be skipped. In addition, with ath12k_mac_get_ar_by_pdev_id() removed,
rcu_read_lock()/unlock() are not needed any more, so remove them. This
also fixes the warning above.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Fixes: 692921ead8 ("wifi: ath12k: flush all packets before suspend")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/ath12k/7a96ca11-80b5-4751-8cfc-fa637f3aa63a@moroto.mountain/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240511095045.9623-1-quic_bqiang@quicinc.com
Introduce a device index parameter in the ath12k_base structure. This
value is used as unique identifier for devices involved in Inter-device
MLO. It is also used to configure the MLO parameter within the QMI host
capability send request. While currently set to zero, future logic will
be added for inter device support to populate this parameter with
non-zero values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430165811.1377182-4-quic_periyasa@quicinc.com
Currently, hardware state is not protected across the reconfigure
operations. However, in single wiphy models, multiple radio/links is
exposed as a MAC hardware (ieee80211_hw) through the driver hardware
abstraction (ath12k_hw) layer. In such scenario, we need to protect
hardware state across the multiple radio/link at the driver hardware
abstraction (ath12k_hw) layer. Therefore, introduce a new mutex in
the ath12k_hw layer.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-4-quic_periyasa@quicinc.com
Currently, in multi wiphy models, the mac80211 hardware state is maintained
within the radio/link structure. However, in single wiphy models, the
mac80211 hardware state is needed at the hardware abstraction layer
(ath12k_hw). Therefore, move the hardware state from the radio/link
structure to the hardware abstraction layer (ath12k_hw). Additionally,
update the naming convention of the state enums to enhance clarity and
consistency.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-3-quic_periyasa@quicinc.com
Currently, in multi-wiphy models, the recovery handler access mac80211
HW from the radio/link structure. This will be incorrect for single wiphy
model, as they will hold multiple link/radio structures. To fix this,
access mac80211 HW based on the number of hardware in the SoC/chip. This
approach makes the recovery handler compatible with both multi wiphy and
single wiphy models.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-2-quic_periyasa@quicinc.com
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable
TAS read the tables from ACPI and send them to the firmware using
WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI
event callback so that ACPI can notify ath12k to get the updated SAR power
table and sends it to the firmware when the device state is changed.
ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid
field. Most likely QCN9274 will never support ACPI as the chip is not used in
laptops.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
Now that all infrastructure is in place and ath12k is fixed to handle all the
corner cases, power down the ath12k firmware during suspend and power it back
up during resume.
For suspend, two conditions needs to be satisfied:
1. since MHI channel unprepare would be done in late suspend stage,
ath12k needs to get all QMI-dependent things done before that stage.
2. and because unprepare MHI channels requires a working MHI stack,
ath12k is not allowed to call mhi_power_down() until that finishes.
So the original suspend callback is separated into two parts: the first part
handles all QMI-dependent things in suspend callback; while the second part
powers down MHI in suspend_late callback. This is valid because kernel calls
ath12k's suspend callback before calling all suspend_late callbacks, making
the first condition satisfied. And because MHI devices are children of ath12k
device (ab->dev), kernel guarantees that ath12k's suspend_late callback is
called after QRTR's suspend_late callback, this satisfies the second condition.
Above analysis also applies to resume process. so the original resume
callback is separated into two parts: the first part powers up MHI stack
in resume_early callback, this guarantees MHI stack is working when
QRTR tries to prepare MHI channels (kernel calls QRTR's resume_early callback
after ath12k's resume_early callback, due to the child-father relationship);
the second part waits for the completion of restart, which would succeed
since MHI channels are ready for use by QMI.
Another notable change is in power down path, we tell mhi_power_down() to not
to destroy MHI devices, making it possible for QRTR to help unprepare/prepare
MHI channels, and finally get us rid of the potential probe-defer issue when
resume.
Also change related code due to interface changes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-10-quic_bqiang@quicinc.com
Currently when resume ath12k_core_restart() calls
ath12k_core_pre_reconfigure_recovery() where mac80211 queues are
stopped by calling ieee80211_stop_queues(). Then in
ath12k_mac_op_reconfig_complete() those queues are not started
because ieee80211_wake_queues() is skipped due to the check on
reconfig_type. The result is that mac80211
could not deliver any frame to ath12k to send out, finally making
connection fail.
[84473.104249] PM: suspend exit
[84479.372397] wlan0: no VHT 160 MHz capability on 5 GHz, limiting to 80 MHz
[84479.372401] wlan0: determined local STA to be EHT, BW limited to 80 MHz
[84479.372416] wlan0: determined AP 00:03:7f:12:b7:b7 to be HE
[84479.372420] wlan0: connecting with HE mode, max bandwidth 80 MHz
[84479.580348] wlan0: authenticate with 00:03:7f:12:b7:b7 (local address=00:03:7f:37:11:53)
[84479.580351] wlan0: send auth to 00:03:7f:12:b7:b7 (try 1/3)
[84480.698993] wlan0: send auth to 00:03:7f:12:b7:b7 (try 2/3)
[84481.816505] wlan0: send auth to 00:03:7f:12:b7:b7 (try 3/3)
[84482.810966] wlan0: authentication with 00:03:7f:12:b7:b7 timed out
Actually we don't need to stop/start queues during suspend/resume,
so remove ath12k_core_pre_reconfigure_recovery() from ath12k_core_restart().
This won't cause any regression because currently the only chance
ath12k_core_restart() gets called is in reset case, where ab->is_reset
is set so that function will never be executed.
Also remove ath12k_core_post_reconfigure_recovery() because it is
not needed in suspend/resume case. This is also valid due to above
analysis.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-9-quic_bqiang@quicinc.com
Currently pktlog is stopped in suspend callback and started in
resume callback, and in either scenarios it's basically to
delete/modify ab->mon_reap_timer and to purge related rings.
For WCN7850 it's pointless because pktlog is not enabled: both
ab->mon_reap_timer and those rings are not initialized.
So remove pktlog handling in suspend/resume callbacks. And
further, remove these two functions and related callee because
no one is calling them.
Other chips are not affected because now only WCN7850 supports
suspend/resume.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-8-quic_bqiang@quicinc.com
In order to send out all packets before going to suspend, current code
adds a 500ms delay as a workaround. It is a rough estimate and may not
work.
Fix this by checking packet counters, if counters become zero, then all
packets are sent out or dropped.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-7-quic_bqiang@quicinc.com
For non-WoW suspend/resume, ath12k host powers down whole hardware
when suspend and powers up it when resume, the code path it goes
through is very like the ath12k reset logic.
In order to reuse that logic, rearrange IRQ handling in the reset
path.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-2-quic_bqiang@quicinc.com
Currently during resume, QMI target memory is not properly handled, resulting
in kernel crash in case DMA remap is not supported:
BUG: Bad page state in process kworker/u16:54 pfn:36e80
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x36e80
page dumped because: nonzero _refcount
Call Trace:
bad_page
free_page_is_bad_report
__free_pages_ok
__free_pages
dma_direct_free
dma_free_attrs
ath12k_qmi_free_target_mem_chunk
ath12k_qmi_msg_mem_request_cb
The reason is:
Once ath12k module is loaded, firmware sends memory request to host. In case
DMA remap not supported, ath12k refuses the first request due to failure in
allocating with large segment size:
ath12k_pci 0000:04:00.0: qmi firmware request memory request
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 7077888
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 8454144
ath12k_pci 0000:04:00.0: qmi dma allocation failed (7077888 B type 1), will try later with small size
ath12k_pci 0000:04:00.0: qmi delays mem_request 2
ath12k_pci 0000:04:00.0: qmi firmware request memory request
Later firmware comes back with more but small segments and allocation
succeeds:
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 262144
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 65536
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
Now ath12k is working. If suspend is triggered, firmware will be reloaded
during resume. As same as before, firmware requests two large segments at
first. In ath12k_qmi_msg_mem_request_cb() segment count and size are
assigned:
ab->qmi.mem_seg_count == 2
ab->qmi.target_mem[0].size == 7077888
ab->qmi.target_mem[1].size == 8454144
Then allocation failed like before and ath12k_qmi_free_target_mem_chunk()
is called to free all allocated segments. Note the first segment is skipped
because its v.addr is cleared due to allocation failure:
chunk->v.addr = dma_alloc_coherent()
Also note that this leaks that segment because it has not been freed.
While freeing the second segment, a size of 8454144 is passed to
dma_free_coherent(). However remember that this segment is allocated at
the first time firmware is loaded, before suspend. So its real size is
524288, much smaller than 8454144. As a result kernel found we are freeing
some memory which is in use and thus crashed.
So one possible fix would be to free those segments during suspend. This
works because with them freed, ath12k_qmi_free_target_mem_chunk() does
nothing: all segment addresses are NULL so dma_free_coherent() is not called.
But note that ath11k has similar logic but never hits this issue. Reviewing
code there shows the luck comes from QMI memory reuse logic. So the decision
is to port it to ath12k. Like in ath11k, the crash is avoided by adding
prev_size to target_mem_chunk structure and caching real segment size in it,
then prev_size instead of current size is passed to dma_free_coherent(),
no unexpected memory is freed now.
Also reuse m3 buffer.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240419034034.2842-1-quic_bqiang@quicinc.com
Link capability categorized as Single Link Operation (SLO) and Multi Link
Operation (MLO).
- Intra-device SLO/MLO refers to links present within a device
- Inter-device SLO/MLO refers to links present across multiple devices
Currently, driver uses a boolean variable to represent intra-device SLO/MLO
capability. To accommodate inter-device SLO/MLO capabilities within the
same variable, modify the existing variable name and type. Define a new
enumeration for the link capabilities to accommodate both intra-device
and inter-device scenarios. Populate the enum based on the supported
capabilities.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240403042056.1504209-2-quic_periyasa@quicinc.com
The initial debugfs infra bringup in ath12k driver and create the ath12k debugfs
and soc-specific directories in /sys/kernel/debug/
For each ath12k device, directory will be created in <bus>-<devname>
schema under ath12k root directory.
Example with one ath12k device:
/sys/kernel/debug/ath12k/pci-0000:06:00.0
ath12k
`-- pci-0000:06:00.0
|-- mac0
To enable ath12k debugfs support (CONFIG_ATH12K_DEBUGFS=y)
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320171305.655288-2-quic_rgnanase@quicinc.com
Implement remain on channel for p2p mode in ath12k_ops:
ath12k_mac_op_remain_on_channel
ath12k_mac_op_cancel_remain_on_channel
P2P device can trigger ROC scan. Then keep listening or sending management
frames on particular channels.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-7-quic_kangyang@quicinc.com
Currently, the rfkill worker handler access mac80211 HW from the radio/link
structure. This is will be incorrect for single wiphy model, as they will
hold multiple link/radio structures. To fix this, access mac80211 HW based
on the number of hardware in the SoC/chip. This approach makes the rfkill
worker handler compatible with both multi wiphy and single wiphy models.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240125154555.3169706-1-quic_periyasa@quicinc.com
QMI PHY capability learn is used to get PHY count information to
support single/multi link operation (SLO/MLO) configuration. The
QCN9274 dualmac firmware currently do not support SLO/MLO, if two
PHYs are within the same chip. Due to this firmware crashes in
split-phy QCN9274, while bringing up AP with MLO parameter enabled
in QMI host capability request message.
The QMI PHY capability learn is not required for split-phy QCN9274,
if SLO/MLO is not supported within the same chip. Hence, disable QMI
PHY capability learn support in split-phy QCN9274.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-14-quic_rajkbhag@quicinc.com
With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.
The hardware param hal_desc_sz value cannot be constant for the same
hardware. It depends on the size of rx_desc structure which may
change based on firmware capability to support word mask subscription.
Hence, remove hal_desc_sz from hardware param and add hal_rx_ops
to get the size of rx_desc in run time.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-9-quic_rajkbhag@quicinc.com
In segment memory mode, firmware allocates memory segments of size
2 MB. This 2 MB memory is used by firmware for the number of peers.
This number of peer is sent from host to firmware during WMI init
command. For single-phy the number of peers sent is
TARGET_NUM_PEERS_SINGLE = 529 (512 + 17). While for split-phy number
of peers sent to firmware is TARGET_NUM_PEERS_DBS = 2 *(512 + 17) =
1058. With this 1058 number of peers firmware is unable to allocate
memory in 2 MB segment and firmware crash is observed.
Hence, fix this firmware crash by reducing the number of stations
TARGET_NUM_STATIONS for split-phy.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-7-quic_rajkbhag@quicinc.com
Firmware IE containers can dynamically provide various information
what firmware supports. Also it can embed more than one image so
updating firmware is easy, user just needs to update one file in
/lib/firmware/.
The firmware API 2 or higher will use the IE container format, the
current API 1 will not use the new format but it still is supported
for some time. Firmware API 2 files are named as firmware-2.bin
(which contains both amss.bin and m3.bin images) and API 1 files are
amss.bin and m3.bin.
Currently ath12k PCI driver provides firmware binary (amss.bin) path to
MHI driver, MHI driver reads firmware from filesystem and boots it. Add
provision to read firmware files from ath12k driver and provide the amss.bin
firmware data and size to MHI using a pointer.
Currently enum ath12k_fw_features is empty, the patches adding features will
add the flags.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123122812.3811251-1-quic_rajkbhag@quicinc.com
To support multi link operation, we need to combine all the link/pdev
under a single wiphy. This avoids the overhead of synchronization
across multiple hardware instances in both the cfg80211 and mac80211
layers. Currently, each link/pdev is registered as separate wiphy,
tightly coupled with link/pdev/radio (ar) structure. To enable single
wiphy registration within the chip, we decouple the wiphy data entity from
the link/pdev/radio (ar) structure and move it under the chip (ab)
structure with a new data container (ath12k_hw) structure. This approach
improves scalability for future multi link operation support.
mac80211 hw private data structure diagram
------------------------------------------
Now After
+---------------------+ +---------------------+
|mac80211 hw priv data| |mac80211 hw priv data|
| | | |
| | | |
| | | |
| | | ath12k_hw (ah) |
| | | |
| | +-------------------> | |
| ath12k (ar) | | +-------------+ |
| | | | | |
| | | | ath12k (ar) | |
| | | | | |
| | | | | |
| | | +-------------+ |
| | | |
| | | |
+---------------------+ +---------------------+
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240118010320.3918136-3-quic_periyasa@quicinc.com
Currently, mac80211 hardware accesses link/radio structure directly in
multiple locations. Introduce helper function to avoid this direct
access, as this change will facilitate refactoring for Multi-link
operation support.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240118010320.3918136-2-quic_periyasa@quicinc.com
Currently, the number of PHY is learned from the firmware service ready
event message. However, on the QCN9274 platform, number of PHY is a
variable parameter. To enable MLO capability in the QMI host capability
request message, the driver needs the PHY count information earlier than
the firmware service ready event. Therefore, a new QMI message,
"PHY capability message", is introduced to retrieve this information.
This message allows the driver to fill in the MLO parameter in the QMI
host capability request message. If the new QMI PHY capability message
fails, the default configuration in the HW params will be used.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240113001659.1022465-3-quic_periyasa@quicinc.com
Currently, the data path pdev pre alloc and mac allocate are called
separately from the core start procedure. The data path pdev pre alloc
can be called from the mac allocate procedure itself since initialization
related to pdev happens in the mac allocate procedure. So move the caller
of DP pdev pre alloc from the core start procedure to the mac allocate
procedure. This change helps in the future to easily decouple the mac
allocate procedure from core start handling in order to support MLO in
multi chip.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231206034920.1037449-2-quic_periyasa@quicinc.com
Sometimes board-2.bin does not have the regdb data which matches the
parameters such as vendor, device, subsystem-vendor, subsystem-device
etc. Add default regdb data with only 'bus=%s' into board-2.bin for
WCN7850, then ath12k uses 'bus=pci' to search regdb data in board-2.bin
for WCN7850.
[ 46.114895] ath12k_pci 0000:03:00.0: boot using board name 'bus=pci,vendor=17cb,device=1107,subsystem-vendor=17cb,subsystem-device=3378,qmi-chip-id=2,qmi-board-id=260'
[ 46.118167] ath12k_pci 0000:03:00.0: boot firmware request ath12k/WCN7850/hw2.0/board-2.bin size 380280
[ 46.118173] ath12k_pci 0000:03:00.0: board name
[ 46.118176] ath12k_pci 0000:03:00.0: 00000000: 62 75 73 3d 70 63 69 bus=pci
[ 46.118179] ath12k_pci 0000:03:00.0: failed to fetch regdb data for bus=pci,vendor=17cb,device=1107,subsystem-vendor=17cb,subsystem-device=3378,qmi-chip-id=2,qmi-board-id=260 from ath12k/WCN7850/hw2.0/board-2.bin
[ 46.118239] ath12k_pci 0000:03:00.0: boot using board name 'bus=pci'
[ 46.119842] ath12k_pci 0000:03:00.0: boot firmware request ath12k/WCN7850/hw2.0/board-2.bin size 380280
[ 46.119847] ath12k_pci 0000:03:00.0: board name
[ 46.119849] ath12k_pci 0000:03:00.0: 00000000: 62 75 73 3d 70 63 69 bus=pci
[ 46.119852] ath12k_pci 0000:03:00.0: boot found match regdb data for name 'bus=pci'
[ 46.119855] ath12k_pci 0000:03:00.0: boot found regdb data for 'bus=pci'
[ 46.119857] ath12k_pci 0000:03:00.0: fetched regdb
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231216060140.30611-6-quic_bqiang@quicinc.com
