Currently wmi.h has two separate set of definitions for peer
flags. One set of flags is defined in enum wmi_tlv_peer_flags, and,
except for the last three, are named WMI_TLV_PEER_*. The other set of
flags are defined as macros, and are named WMI_PEER_*. The last three
macros have the same name as the last three wmi_tlv_peer_flags
enumerators.
The code only uses the WMI_PEER_* names; the WMI_TLV_PEER_* names are
unused. So as a first step in consolidation, remove all the
WMI_TLV_PEER_* names.
But since having an enum to define all the flags is actually a good
thing since that provides a handle by which to refer to the entire set
of flags, recast the WMI_PEER_* macros into enumerators.
Compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231106-ath-peer-flags-v1-4-781e83b7e8e8@quicinc.com
In a special WCN7855 firmware release the EHT (IEEE 802.11be) support has
been disabled for size reduction. Currently ath12k always enables EHT PHY
mode during vdev start but with the special firmware that will cause a
firmware crash during vdev start in firmware initialisation. This is
because the firmware will use the EHT mode to allocate resources but as
the EHT mode is not available in the firmware, there's an internal
conflict and the firmware will crash.
To fix the crash check the WMI_TLV_SERVICE_11BE flag to see if the firmware
supports EHT. If EHT is not supported downgrade the PHY mode to HE
(IEEE 802.11ax).
This does not impact QCN9274, because WMI_SERVICE_11BE is always enabled
for QCN9274, then eht_cap->has_eht will always set for it, and the logic
of this patch will not take effect and the PHY mode will not down grade
for it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230913105757.17744-1-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
Add WMI support to process the EHT capabilities passed by
the firmware. Add required EHT specific definitions in
structures ath12k_band_cap and ath12k_wmi_svc_rdy_ext_parse.
For single_pdev chip such as WCN7850, only one pdev is created
and only one hardware is registered to mac80211. This one pdev
manages both 2.4 GHz radio and 5 GHz/6 GHz radio.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-4-quic_alokad@quicinc.com
Currently there are about 60 channels for 6 GHz, then the size of
chan_list in struct scan_req_params which is 40 is not enough to
fill all the channel list of 6 GHz.
Use dynamic memory to save the channel list of scan.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230717033431.21983-1-quic_wgong@quicinc.com
In order to support different power levels of 6 GHz AP and client, new WMI
event for regulatory (WMI_REG_CHAN_LIST_CC_EXT_EVENTID) has been added in
firmware to provide new parameters required for 6 GHz regulatory rules.
Firmware advertises its capability of handling new event in WMI service ready
event. Based on that, host needs to set host_service_flags in WMI init command
to indicate that host supports processing of this WMI event. Based on
advertised host capability, firmware sends event WMI_REG_CHAN_LIST_CC_EXT_EVENTID.
This new event contains 2G/5G/6G reg rules with additional power value fields
for 6GHz and regd is built accordingly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230502142018.20301-1-quic_rgnanase@quicinc.com
When vdev start/stop happens, response from firmware is received with delay
and hence there is a timeout before VDEV can be up/down.
Also, with maximum peers connected and when vdev stop occurs, firmware
will take time to clean up all the peers and vap queues.
In such cases as well, vdev start/stop response is sent by firmware with delay.
Increase the vdev setup timeout as recommended by firmware team.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aishwarya R <quic_aisr@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230428091041.20033-1-quic_rgnanase@quicinc.com
Both PSOC_HOST_MAX_NUM_SS and WMI_MAX_NUM_SS are set to 8. The host assumes
that the values are the same but there's no check for that, so things will
break if either of the values change. It's simpler and safer to have just one
define so delete PSOC_HOST_MAX_NUM_SS and use WMI_MAX_NUM_SS everywhere.
No functional changes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220120655.19389-4-kvalo@kernel.org
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
